3 Axis Accelerometer ADXL 335
7 PIN 0.96” 128*64 WHITE OLED
- High resolution: 128*64
- Input voltage: 3V to 5 V DC
- Ultra-wide viewing angle >160 degree
- Ultra-low power consumption
- Fully compatible with Arduino, 51 series, MSP430, STM32/2, CSR IC.
- Driver IC: SSD1306
- Display colour: white
- Performs without the need for a backlight
- Interface: IIC/SPI, needs 4 I/O only
- Compatible I/O level: 3.3v, 5v
- Working temperature: -40 degrees to 70 degrees Celsius
- Dimension: 27.3*27.8*3.7mm
- Support a wide range of input
- Size: 99gm
Anti-Corrosion Water Level Sensor with Ball Float Switch
- Rating Contract (Max.): 10 W
- Switching Power Supply (Max.): 110VDC
- Pulse current (Max.): 0.5A
- Breakdown Voltage (Max.): 220VDC
- Current (Max.): 1A
- Resistance Contract (Max.): 100 Ω
- Operating Temperature: -10 to 60degree C
- Cable length: 40cm
- Shipment Weight: 0.02 kg
- Float Ball Size : 24×17mm
- Body Total Length: 85mm
- Total Float opening: 70°
- Float Switch ON/OFF angle: Approx. between 15° to 20°
APDS-9930 Gesture Sensor Digital Proximity And Ambient Light Sensor For Arduino
- Working voltage:2.8-3.8V
- ALS, IR LED, and Proximity Detector in an Optical Module
- Approximates Human Eye Response
- Programmable Interrupt Function with Upper and Lower Threshold
- Programmable range from 2.7 ms to more than 8 seconds
- Up to 16-Bit Resolution
- High Sensitivity Operates Behind Darkened Glass
- Low Lux Performance at 0.01 lux;
- Ambient Light Sensing (ALS)
- Proximity detection
- I2C interface is compatible up to 400kHz (I2C fast mode) –
CD74HC4067 High Speed CMOS 16-Channel Analog/Digital Multiplexer Breakout Module
Delay Timer Switch Adjustable 0-10sec With NE555 Electrical Input 12V 10A
- Module based on the NE555 chip.
- Input voltage: DC 12V
- Adjustable time: 0-10 s
- AC Control voltage: 250V/max. 10A
- DC Control Voltage: 30V/max. 10A
- load: 2200W
- Precision Pulse Generation / Timing.
- Monostable Operation.
- Standby no power consumption
- Excellent temperature stability of 0.005%/°
- Time can be adjusted by a potentiometer, the default is 0-25 seconds
DHT22 MODULE
- Power supply: 3.3-5.5VDC
- Operating range: humidity 0-100%R
- Ultra-Low Power.
- No Additional Components.
- Long-Distance Signal Transmission.
- All Calibration, Digital Output & Completely Interchangeable.
- Relative Humidity & Temperature Measurement.
- Humidity Measurement Precision: 2-5% RH.
- Temperature Measurement Precision: 0.5 deg C.
- Calibrated digital signal
- Outstanding long-term stability
Double Analog Potentiometer Module With Slide Potentiometer Slip Adjustable Resistance For Arduino
- Dual analogue output, output 0-VCC analogue voltage signal.
- Voltage: 3.3V, 5V.
- Port: Analog.
- Resistance: 10K.
- Slide potentiometers module
- Two analogue outputs, analogue outputs 0-VCC voltage signals
- Stable and reliable performance with high-quality sliding appliances
- Platform: Arduino, MCU, ARM, and other microcontroller platforms
- Application: Raspberry Pi projects, DIY projects, Arduino projects.
- Dimensions: 91 x 21 x 30 mm
- Weight: 18 gm.
DS18B20 MODULE
- Resolution: 9bits to 12bits (Selectable)
- Supply Voltage (V): 3 to 5.5
- Temperature Range(°C): -55 to +125
- Measuring Accuracy(°C): ±0.5
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into the chip
- Multiple sensors can share one pin
- Maximum conversion time and response: 750 ms
- Multidrop capability simplifies distributed temperature sensing applications
- Requires no external components
- Digital signal output
- 18B20 Temperature Sensor Chip
- Send data via a pin
- User-definable nonvolatile (NV) alarm settings
- Dimension: 19*15*6cm
- Weight: 9gm
DS18B20 PROBE
- Usable temperature range: -55 to 125°C (-67°F to +257°F)
- 9 to 12-bit selectable resolution
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into a chip
- Multiple sensors can share one pin
- ±0.5°C Accuracy from -10°C to +85°C
- Temperature-limit alarm system
- Query time is less than 750ms
- Usable with 3.0V to 5.5V power/data
- Each pin uses a heat-shrinkable tube to prevent short circuit, internal sealing glue.
- Stainless steel tube encapsulation waterproof moistureproof prevents rust.
- Stainless steel tube 6mm diameter by 30mm long.
- Contains DS18B20 temperature sensor.
- Uses 1-Wire interface- requires only one digital pin for communication.
- Unique 64 bit ID burned into the chip.
- Multiple sensors can share one pin.
- Temperature-limit alarm system.
- Without the external components, the unique single bus.
EYE BLINKING SENSOR
- Working Voltage +5V DC
- TTL output 5V or 0VSimple setup.
- Remote detection - no mechanical contact with the eye.
- Stray visible and IR light not affected.
- Our system does not require the restraint of the external eyelids.
- Head movement not affected.
- Excellent frequency characteristics (DC to more than 500 Hz).
- Excellent working distance (15-25 mm).
- Difficult to calibrate using common units of eye blink measurement. (e.g. mm of eyelid displacement)
Finger print Scanner Module – TTL (GT-521F32)
- Operating Voltage: 3.3V to 6V DC
- Simple UART & USB communication protocol.
- Complies with USB 2.0 full-speed specification.
- Ultra-thin optical sensor.
- Finger window: 12.9 x 16.9 mm.
- Image Size: 258 x 202 Pixels.
- Resolution 450 dpi.
- Capable of 360° recognition.
- Storage for 200 unique fingerprints.
- False Acceptance Rate (FAR): <0.001%
- False Rejection Rate (FRR): <0.01%
- Wake up on Finger Function.
- CPU: ARM Cortex M3 Core MCU).
- Ultra-thin Optical Sensor.
- Works well with dry, moist or rough fingerprints
- Anti-scratch with surface high hardness ≧5
- 1:1 verification, 1:N identification.
- High accuracy and high-speed fingerprint identification technology.
- External UART-to-USB converter required (TX & RX levels: 3.3V).
Force Sensor 38.1mm
- Easily customizable to a wide range of sizes
- Cost-effective
- Ultra-thin; 0.45 mm
- Life: up to 10 million actuations
- Simple and easy to Integrate.
- Actuation Force: 0.1 Newtons
- Force Sensitivity Range: 0.1 - 10.02 Newtons
- Non-Actuated Resistance: 10M W
- Device Rise Time: <3 microseconds
- Temp Operating Range: 30 - +70 ºC
- 16MHz Clock Speed
- 32 KB Flash Memory
- Overall length: 1.75 inches
- Overall width: 0.28 inch
- Sensing area: 0.3 inch
GY-50 L3G4200D 3-Axis Gyroscope/ Gyro Sensor Module for Arduino
- Sensor type - Gyroscope, 3 axes.
- Voltage Supply - 2.4 V - 3.6 V.
- IC - L3G4200D.
- Communication Mode: IIC / SPI communications protocol
- Sensing Range - Three selectable full scales (250/500/2000 DPS).
- 16-bit rate value data output
- 8-bit temperature data output
- 32 count FIFO buffer
- Output Lines - Two Digital Output Lines (Interrupt and data ready).
- Operating Temperature: -40 to +85 °c
- Integrated low and high pass filters with user-selectable bandwidth
- Embedded self-test
- Low voltage compatible IOs, 1.8 V
- Embedded power-down and sleep mode
- High shock survivability
- 3-axis angular rate sensor (yaw, pitch & roll) make it great for model aircraft navigation systems.
HC-06 Bluetooth Module
- Input Supply voltage: 3.6 - 6V
- Input current: 50 (mA)
- Maximum Operating Range: 10m
- Operating Frequency: 2.4GHz ISM band
- Modulation: GFSK (Gaussian Frequency Shift Keying)
- Emission power: 4dBm, Class 2
- Sensitivity: -84dBm at 0.1% BER
- Operating Temperature: -20 ~ +75 degree C
- Potter default rate of 9600, the user can be set up.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Speed: Asynchronous: 2.1Mbps (Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- Security: Authentication and encryption.
- Profiles: Bluetooth serial port.
Ina219 I2C BiDirectional DC Current Power Supply Sensor Breakout Module
- 1 ohm 1% 2W current sense resistor
- Up to +26V target voltage
- Up to ±3.2A current measurement, with ±0.8mA resolution
- Senses Bus Voltages from 0 to 26 V
- I2C- or SMBus-compatible interface. The
- Reports Current, Voltage, and Power
- 16 Programmable Addresses
- Filtering Options
- Calibration Registers
- SOT23-8 and SOIC-8 Packages
- Using a single power supply, the working voltage is between + 3.0 to + 5.5 V.
- Calibration programmable registers directly read its unit of measure in the ampere current, and power in watts per reading.
- For as many as 128 samplings averaging, in order to realize filter in the noise environment.
- The I2C interface timeout, not only avoid the bus lock but also can provide high-speed mode, meet the communication requirements of up to 3.4 MHz.
- Supported software programmable INA219.
- Dimensions: 0.9*0.8inch
- Weight: 1.9g
IR Proximity Module using TSOP
- Operating wavelength: Near-infrared region 700 nm to 1400 nm
- Main Chip: LM358
- Operating Voltage Range: 3.6V-5V DC
- Average Current Consumption: 06mA
- Distance Measuring Range: 2 to 30cm
- Detection angle: 35 °
- Easy to assemble and use
- On-board detection indication
- the effective distance range of 2cm to 80cm
- A pre-set knob to fine-tune distance range
- If there is an obstacle, the indicator lights on the circuit board
- 3mm screw holes for easy mounting
- Dimensions: 48 x 14 x 8mm
- Weight:5gm
LJ12A3-4-Z/BY PNP DC6-36V 8 mm INDUCTIVE PROXIMITY SENSOR
- Output type: PNP NO
- Supply voltage: 6V-36V
- Current output: 300mA
- Response frequency: 0.5khz
- Detecting distance: 4mm
- Wire type: cylindrical DC 3 wire type
- Switch appearance type: cylinder type
- Operating temperature: -25 degrees to 55 degrees Celsius
- Detect object: iron
- Red led checks proximity status
- High repeated positioning accuracy
- High switching frequency
- Reverse power protection, short circuit protection, directly connecting with PLC
- anti-vibration, dust, water, and oil prevention
- Dimension: 5*3*3cm
- Weight: 400gm
Load Cell CZL 601 80KG
- Type: Single Point Load Cell
- Total Precision: C3 class
- Material: Aluminum Alloy
- Surface: Anodized Treatment
- Protection: IP65
- Rated Load: 80 Kg. Max
- Rated Output : 2.0 mV/V+/- 5%
- Zero Balance : +/- 1% Full Scale
- Excitation Voltage: 9-12 Volt DC
- Nonlinearity : 0.017% Full Scale
- Hysteresis: 0.02% Full Scale
- Repeatability : 0.01% Full Scale
- Creep(30min) : 0.015% Full Scale
- Operating Temperature : -20 °C to +65 °C
- Safe Overload: 120% of Rated Capacity
- Ultimate Overload: 150% of Rated Capacity
- Cable: 420mm (3mm dia 4 wire shielding cable)
MAX7219 Dot Led Matrix Module 4 In 1 Display with 5P Line Module For Arduino Micro-controller
- Driver Chip: MAX7219
- Input Voltage: 3.7 to 5.3 V
- Input Current: 320 mA
- Requires only 3 communication wires of MCU
- Pre-cascaded MAX7219 Dot Matrix LED Module.
- The overall size of the display is very compact
- With 64 fixing screw holes, hole diameter: 3mm.
- M3 holes for mounting.
- Module with input and output interfaces
- Support for cascading multiple modules
- Quite large display
- Display Dimensions: 32x32x6 mm
- PCD Dimensions: 128×32mm
- Weight: 55 gm
MCP2515 CAN Module TJA1050 Receiver SPI 51 Single Chip Program Routine Arduino
- Input Supply voltage: 5V
- Input Supply Current: 5 mA
- Support CAN V2.0B technical standard, communication rate 1Mb / S.
- 0 to 8 bytes long data field.
- 8MHZ crystal oscillator
- 120Ω terminal resistance
- Use High-speed CAN transceiver TJA1050
- SPI control for expanding Multi CAN bus interface
- Using serial port could view the communication data
- With the independent key, LED indicator, Power indicator
- With power pin
- Positioning screw hole centre spacing 23 mm x 38 mm
- The working current: typical 5mA, standby current 1 microamp. Except for the power indicator.
- Standard frames, extended frames, and remote frames.
- Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation
Mini ESP-M2 ESP8285 Serial Wireless WiFi Transmission Module SerialNET MODE Fully Compatible With ESP8266
ESP8285 M2 WiFi IoT Module :
- SOC characteristics.
- Built-in Tensilica L106 ultra-low power 32-bit CPU, main frequency supports 80MHz and160MHz and RTOS.
- Built-in TCP/IP protocol.
- Built-in one-channel 10-bit high precision ADC.
- Outboard interface: HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO.
- The deep sleep current is 10uA, the cut-off current is smaller than 5uA.
- Wake, connect and transmit data package within 2ms.
- The consumer power is smaller 1.0Mw (DTIM3) when at standby status.
- Built-in 1M byte for SPI Flash.
- Ultra-small size.
- Support serial to WiFi.
- Wireless transparent transmission.
- Long-distance transmission with ultra-low power.
- Support outboard antenna.
- Bearing high temperature to 125 °C, compared to the 85°C for ESP8266.
- Support 802.11 b/g/n/e/I.
- Support Station, Soft AP, Soft AP+STA mode.
- Support WiFi Direct (P2P).
- Support CCMP (CBC-MAC, computation mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc., for hardware acceleration.
- P2P finding, P2P GO mode/ GC mode and P2P power management.
- WPA/PA2PSK and WPS.
- 11securitycertification: pre-certification and TSN.
- Support 802.11n (2.4GHz).
- 1h/RFC1042 frame encapsulation.
- Support seamless roaming.
- Support AT remote update and cloud update (OTA).
- Support Smart Config function (including Android and Ios device
Mini Ultra-small Size ESP-M3 From ESP8285 Serial Wireless WiFi Transmission Module Fully Compatible With ESP8266
- Model: ESP8285 ESP-M3
- 32-bit Tensilica L106 microcontroller
- Ultra-low 16 bit RISC
- Fully Compatible with ESP8266
- Embedded TCP protocol
- channel high-precision 10-bit ADC
- Supporting the most commonly used networks (802.11 b / g / n)
- Support WPA, PA2PSK and WPS
- Working temperature: -40 ℃ - + 125 ℃
- Clock Speed: 80 MHz; (max 160 MHz)
- Flash memory: 1 MB
- Interface: HSPI, UART, I2C, I2S, Remote Control IR Control, PWM, GPIO
- Direct WiFi Support (P2P)
- Support mode: CCMP, TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc
- Low consumption
- Easy access to the pins
MPU6050 6AXIS (GYROSCOPE + ACCELEROMETER) SENSOR
- MEMS 3-axis accelerometer and 3-axis gyroscope values combined
- Power Supply: 3-5V
- Communication: I2C protocol
- Built-in 16-bit ADC provides high accuracy
- Sensing range: +/-2G to +/-16G
- Built-in DMP provides high computational power
- Can be used to interface with other IIC devices like a magnetometer
- Configurable IIC Address
- In-built temperature sensor
- Ideal for noisy power environment
- Operating temperature: -40 degrees to 85 degrees Celsius
- Dimension: 28*14mm
MQ135 Module
- Working voltage: DC 5V
- Working Current: 150mA
- DOUT: TTL output
- AOUT: Analog output
- Preheat time: Over 20s
- Detection Range: 10 - 300 ppm NH3, 10 - 1000 ppm Benzene, 10 - 300 Alcohol
- Sensitivity to Ammonia, Sulphide, and Benzene steam
- With signal output instructions
- The TTL output signal is a low level
- Analog 0 ~ 5 v voltage output, the higher the concentration, the higher the voltage
- Sensitive for benzene, alcohol, smoke
- Fast response and recovery
- Adjustable sensitivity
- Signal output indicator
- Dimension: 32mm x 22m x 27mm
MQ7 Module
- Operating voltage: DC 5 V.
- Interface Type: Analog
- The analogue output voltage, the higher the concentration the higher the voltage.
- Detection Gas: carbon monoxide
- Detection range: 10 to 10000ppm
- Four screw holes for easy positioning.
- Has a long life and reliable stability.
- Fast response and recovery characteristics.
- Adjustable sensitivity
- Dimension: 32mm x 22m x 27mm
MT8870 DTMF Audio/Speech Decoding Telephone Module
- Power Input: 5V Nominal (4.5V - 5.5V)
- 5 Channel Interface
- Detects 0-9, A-D, *, #
- 54” Pin pitch
- On-board 3.5mm jack input Facility
- On-board MT8870 frequency decoder chip
- On-board voice input interface
- On-board LED lights for output state indication
- Low power consumption
- Internal gain setting amplifier
- Adjustable guard time
- 5 Channel interface
- Power-down mode
- Inhibit mode
- Does not require external circuits or wiring,
- Dimension: 37 x 25 x 12 mm
PCF8574 I/O For I2C Port Interface
- Communication: I2C
- Operating Voltage: 2.5-V to 6V.
- Open-Drain Interrupt Output
- Compatible With Most Microcontrollers
- 8-bit remote I/O pins
- Up to 64 I/O ports
- Low standby current
- Operating temperature: 40 degrees C to +85 degree C
- Supports Arduino cascading, and you can use at most 8 modules to extend 64 I/O at the same time.
- the address can be changed by a set a toggle switch.
- Every 2 seconds, make P0-P7 port output High level, Low level, and put 3 toggle switches to ON, the address of module is 0x27.
- PCB Size: 36 x 16mm
pH Sensor Module & pH electrode Probe for Arduino, AVR, PIC
- Module Power: DC 5.00V.
- Measuring Range: 0-14PH.
- Accuracy: 0.01 pH
- Response Time: ≤ 1min.
- Industry pH Electrode with BNC Connector.
- Power Indicator LED.
- Output: Analog values in the range of (0.5V to 3V).
- Alkali Error: 0.2PH.
- Internal Resistance: 250MOhm.
- Gain adjustment Potentiometer.
- Measuring Temperature: 0 degrees to 50 degrees C
- Terminal Blocks: BNC plug.
- BNC Connector is suitable for most pH meters and controllers.
- Suitable for a wide range of applications: Aquariums, Hydroponics, Laboratory etc.
- Module Size: 50 x 47 x 16mm
PIR Sensor
- Wide Working Voltage Range: DC 4.5V- 20V
- Current Drain: <60uA
- Detection Angle: <140°
- Detection Distance: 3 to 7m (can be adjusted)
- Blockade time: 2.5s (Default)
- Work temperature: -20-+80°C
- Colour: White + Green OR White + Blue
- Infrared Sensor with Control Circuit Board
- The Sensitivity and Holding Time Can be Adjusted
- Voltage Output: High/Low level Signal: 3.3V TTL output
- Delay Time: 5 to 200s (Can be Adjusted, Default 5s +/- 3%)
- Blockade time: 2.5s (Default)
- Sensitive Setting: Turn to Right, Distance Increases (About 7M); Turn to Left, Distance Reduce (About 3M)
- Time Setting: Turn to Right, Time Increases (About 200S); Turn to Left, Time Reduce (About 5S).
- Dimension: 3.2cm x 2.4cm x 1.8cm
Pixy2 CMUcam5 Smart Vision Sensor – Object Tracking Camera for Arduino, Raspberry Pi, BeagleBone Black
- Pixy2 detects lines, intersections and small barcodes, intended for line-following robots.
- Improved framerate – 60 frames-per-second.
- Tracking algorithms have been added to colour-based object detection.
- Improved and simplified libraries for Arduino, Raspberry Pi and other controllers
- Integrated light source.
- The small, fast, easy-to-use, low-cost, readily-available vision system
- Learns to detect objects that you teach it
- Connects to Arduino with the included cable. Also works with Raspberry Pi, BeagleBone and similar controllers.
- Supports C/C++ and Python
- Communicates via one of several interfaces: SPI, I2C, UART, USB or analogue/digital output.
- Configuration utility runs on Windows, macOS, and Linux.
- All software/firmware is open-source GNU-licensed.
- Dimensions: 43mm x 39mm x 16mm
- Height of Camera: 4mm / 0.16""
- Weight (no IDC cable, no screws): 10g.
R305 Optical Fingerprint Reader Sensor Module
- Power DC: 3.6V-6.0V
- Interface : UART (TTL logical level)/ USB 1.1)
- Working current: 100mA
- Peak Current: 150mA
- Matching mode (1: 1)
- Search method (1: N)
- Connecting cable length (cm): 8.5
- Baud rate (9600*N)bps, N=1-12 (default N=6 57600bps)
- Character file size: 256 bytes
- Image acquiring time: <0.5s
- Template size: 512 bytes
- Storage capacity: 256
- FAR : <0.001%; FRR: <0.1%
- Average searching time: < 0.8s (1:880)
- Working environment: Temp: -10degree to +40degree C
- Storage environment Temp: -40degree to +85degree C
- RH: 40%-85% RH: <85%
- Integrated image collecting and algorithm chip together, ALL-in-One.
- Low power consumption, low cost, small size, excellent performance.
- Professional optical technology, precise module manufacturing techniques.
- Good image processing capabilities can successfully capture an image up to a resolution of 500 dpi.
- Window dimension : 18mm*22mm
- Optical module: 49 x 20 x 21.20 mm
- Touch Sensors: 18 x 14.5 mm.
- Weight: 16gm
RCWL-0516 Microwave Radar Sensor
- Operating Voltage: 4 to 28 V DC
- Operating Current: 2.8mA (typical); 3mA (max)
- Detecting Range: 5-9m
- Transmitting Power: 20mW (typical); 30mW (max)
- Output Voltage: 3.2 to 3.4v
- Output Voltage Driving Capacity: 100mA
- Output Control Low Level: 0V
- Output Control High Level: 3.3V
- Operating Temperature (C): -20 to 80 degree C
- Transmission signal processing control chip RCWL-9196
- Penetrating detection capability, compared with the traditional infrared feeling PIR
- Adjustable Block time and distance
- Dimension:36*17*2mm
- Weight: 3gm
Sim800C GPRS/GSM Shield with Antenna
- Chip: QuadBand SIM800C GSM CHIP.
- Supply voltage range: 4 to 4.4V
- Quad-band 850/900/1800/1900MHz
- GPRS multi-slot class 12/10
- GPRS mobile station class B
- Compliant to GSM phase 2/2+
- Control via AT commands
- Configurable baud rate.
- SMA connector with GSM L Type Antenna.
- Built-in SIM Cardholder on Top Side.
- Arduino compatibility: Arduino UNO R3, Arduino Mega etc.
- Antenna type: Finger antenna.
- Output: TTL and RS232 serial output.
- Simcard holder: standard size.
- Buzzer for CALL and SMS indication
- Built-in Network, Status leds.
- Inbuilt Powerful TCP/IP protocol stack for internet data transfer over GPRS.
- Normal operation temperature: -20 °C to +55 °C.
- On-Board Buzzer for Ring Indication.
- On-Board provision for Speaker and Mic.
- Low power consumption
- Dimensions: 17.6*15.7*2.3mm
- Weight: 1.3g
Socket Adapter Plate Board for 8 Pin Nrf24L01 Wireless Module
- Used with NRF24L01 wireless module
- Add core nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
- Onboard 3.3V voltage regulator accepts your Arduino +5V supply and provides 3.3V for the attached nRF24L01+ module
- Allows for easy connection to nRF24L01+ modules
- Small power on SMD LED indicator
- On-Board Voltage Regulator:
- Dimension: 15.3 x 11.5 x 1.2 cm
- Weight: 10 Grams
Solid Relay Module 2 channel 5v low level trigger for Arduino
- 5V Solid State 2-channel Relay
- Output With resistive fuse 240V 2A.
- Input Power: 5V DC (160MA).
- Input control signal voltage: 0 - 2.5V state low relay OFF/3.3V - 5V state high relay ON
- Working current: 12.5mA.
- Trigger voltage: 2.5v
- Trigger current: 2mA.
- Rated output load: 100V to 240V AC (50Hz/ 60Hz) 2A per channel
- Rated input power: 5V, 160mA (all channels ON)
- Triggered at Low level (or Active Low)
- Separate LEDs showing the status of each Solid-State Relay
- Input control signal:
- -Low Signal (Solid-State Relay ON / CLOSE), 0V- 2V or GND
- -High Signal (Solid-State Relay OFF / OPEN), 3.3V - 5.0V or leave it floating
- Used in PLC control, home intelligent control, industry, electronic DIY etc.
- Dimension: 25mm x 34mm x 22mm