Stepper Motor NEMA 34 122 kg-cm Hybrid Bipolar
- Rated Voltage:4.08V
- Phase: 2
- Current/ phase: 4A
- Holding Torque: 122 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 37mm
- Shaft Diameter: 13mm
- Long-lasting life
- Low cost for control achieved
- High torque at startup and low speeds
- Ruggedness
- Simplicity of construction
- Can operate in an open-loop control system
- Low maintenance
- Less likely to stall or slip
UNITE DC 48V 750W BM1418ZXF Brushless Gear Motor
Leadshine DMA860H
- Input voltage: Up to +80VAC or +110VDC.
- Output current Up to 7.2A.
- Pulse input frequency up to 300 KHz.
- Automatic idle-current reduction.
- Over-voltage, over-current protection.
- Suitable for 2-phase and 4-phase motors.
- Support PUL/DIR and CW/CCW modes.
- Operating Temperature : 70 C.
- High performance, cost-effective
- Self-adjustment technology
- Pure-sinusoidal current control technology
- TTL compatible and optically isolated input
- 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
UNITE DC 48V 350W BM1418ZXF Brushless Gear Motor
Stepper Motor NEMA 34 46 kg-cm Hybrid Bipolar
- Rated Voltage:4.2V
- Current/ phase: 4A
- Inductance/ phase: 7.3mH
- Resistance/ phase: 0.87ohms
- Holding Torque: 46 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 32mm
- Shaft Diameter: 12mm
- They are high torque stepper motors.
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing
48v 500W BM1418ZXF Brushless Motor
Leadshine DMA860E Stepper Motor Driver
- Model: DMA860E.
- Control Mode: Step & Direction.
- Max Input Frequency: 200 kHz.
- Input Voltage Range: 18 - 80 VAC / 24 - 110 VDC.
- Suggested Power Supply Voltage Range: 36-90 VDC /24-60 VAC.
- Number of DIP Switch Resolution Configurations: 16.
- 16 selectable micro-step resolutions of 400-51,200 via DIP switches.
- 8 selectable output current settings of 2.4 – 7.2A via DIP switches.
- Logic Current Range: 7-16mA (10mA typical).
- Logic Voltage Range: 4-5 VDC for pulse active high (default), or 0-0.5V for pulse active low.
- Pulse enabled at: Rising edge.
- Idle Current Percentage: 50 %.
- Number of Digital Inputs: 3.
- Step Width: 2,500 ns.
- Minimal Direction Setup Time: 5,000 ns.
- Isolation Resistance: 500M Ohm..
- Ambient Temperature: 0-50°C.
- Humidity: 40–95% RH.
- Operating Temperature: 0-70°C.
- Vibration: 5.9 m/s2 Max.
- Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors.
- Step & direction (PUL/DIR) and CW/CCW (via internal jumper set) control. Step & direction by default Multi-Stepping for smooth motor movement.
- Opto Isolation for input control signals.
- Soft-start with no “jump” when powered on.
- Protections for over-voltage and over-current.
- Dimension: 5.94 X 3.82 X 2.24 Inches.
- Weight: 1.13 lbs.
Stepper Motor NEMA 34 68 kg-cm Hybrid Bipolar
- Rated Voltage:4.2V
- Current/ phase: 4A
- Holding Torque: 68 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 32mm
- Shaft Diameter: 12mm
- Long-lasting life
- Low cost for control achieved
- High torque at startup and low speeds
- Ruggedness
- Simplicity of construction
- Can operate in an open-loop control system
- Low maintenance
- Less likely to stall or slip
Leadshine DM320C
- Supply voltage up to +30 VDC
- Output current programmable, from 0.3A to 2.0A
- Pulse input frequency up to 70 kHz
- TTL compatible and optically isolated input
- Automatic idle-current reduction
- Suitable for 2-phase and 4-phase motors
- Support PUL/DIR and CW/CCW modes
- Over-voltage, over-current, phase-error protection
- Anti-Resonance provides optimum torque and nulls mid-range instability
- Self-test and Auto-configuration technology offers optimum responses with different motors
- Microstep resolutions programmable, from full-step to 102,400 steps/rev
- Support PUL/DIR and CW/CCW modes
- Over-voltage, over-current, phase-error protection
- Its unique features make the DM320C an ideal solution for applications that require low-speed smoothness
Stepper Motor NEMA 34 87 kg-cm Hybrid Bipolar
- Rated Voltage:4.2V
- Current/ phase: 5A
- Holding Torque: 87 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 32mm
- Shaft Diameter: 12mm
- They are high torque stepper motors.
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing
Metal Gear Servo Motor GS-5515MG
- Control System: Positive PWM control (1500 usec neutral)
- Operation Voltage Range: 4.8V - 0V
- Operation Temperature Range: -20 C - +60 degree C
- Test Voltage:
- Standing Torque@ 4.8V: 13kg-cm
- Speed@ 4.8V : 0.31 sec / 60 at no load
- Idle Current@ 4.8V: 250mA at stopped
- Running Current@ 4.8V: 2000mA at no load
- Standing Torque@ 6.0V: 15kg-cm
- Speed@ 6.0V: 0.28 sec / 60 at no load
- Idle Current@ 6.0V: 300mA at stopped
- Running Current@ 6.0V: 2200mA at no load
- Dead Band Width: 8 usec
- Circle: 10000 times
- Direction: Re-clock wise/ pulse travel 1500 to 1900 usec
- Drive type: FET drive
- Motor Type: Carbon brush
- Size: 41.2*20.2*37.7 mm
- Weight: 63g without splined horn
- Ball Bearing: Double ball bearing
- Gear Material: Metal gear
- Case Material: Nylon plus fiber
- Connector Wire Length: 300mm
- Connector Wire Gauge: 22AWG heavy duty (Futaba universal)
FEETECH FT6560M 65kg Large Scale High Torque Servo
- Model: FT6560M.
- Operating Speed6.0v 0.15 sec/60°.
- Operating Speed7.4v 0.13 sec/60°.
- Stall Torque 6.0v 48 kg.cm.
- Stall Torque 7.4v 62 kg.cm.
- Motor: carbon.
- Control Way: Digital.
- Cable Length: 20cm.
- Gear: 5 metal gears.
- Bearing: 2BB.
- Dead band: 4us.
- Working frequency: 330hz.
- Wire/Color: JR 265 mm/ -Brown +Red S Orange.
- Dimensions: 65.8X30.2X57.4mm.
- Weight: 200 g.
Leadshine DM542
- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Extremely cost-effective
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology
- TTL compatible and optically isolated input
- 15 selectable resolutions in decimal and binary, up to 25,600 steps/rev
- Suitable for 2-phase and 4-phase motors
- DIP switch current setting with 8 different values
- Support PUL/DIR and CW/CCW modes
- Short-voltage, over-voltage, over-current protection
DM556 Digital Stepper Motor Driver with Micro Stepping 20 to 50V 5.6A
- Good high-speed performance
- Supply voltage: +50VDC
- Output current from 0.5A to 5.6A
- Pulse input frequency up to 200 kHz
- Extremely cost-effective
- Automatic idle-current reduction
- Self-test and Auto-configuration technology TTL compatible and optically isolated input
- Micro step resolutions programmable, from full-step to 102,400 steps/rev
- Suitable for 2-phase and 4-phase motors
- Support PUL/DIR and CW/CCW modes
- Anti-Resonance provides optimum torque and nulls mid-range instability
- Extra-low motor noise offers excellent quietness
- Over-voltage, over-current protection and phase error protection
BM1418ZXF 48V 750W Controller for Brushless DC Motor
- Rated Voltage: 48V.
- Rated Output Power: 750W
- Speed after Reduction: 480 RPM
- Rated Speed: 2800 RPM
- Gear Ratio: 1:6
- Throttle: 1-4V.
- Full Load Current: 20A
- No Load Current: 5A
- Rated Torque: 15.36 N.m.
- Load Capacity: Up to 350 KG
- Small and Medium-size E-Tricycle
- Short voltage protection: 31.5±0.5V/42±0.5V.
- Colour: silver.
- Casing material: Aluminium.
- Dimension: 105 x 65 x 32mm
NEMA 34 34 kg-cm Bipolar Hybrid Stepper Motor
- Rated Voltage:4.2V
- Current/ phase: 3A
- Inductance/ phase: 3.6mH
- Resistance/ phase: 1.4ohms
- Holding Torque: 34 kg-cm
- of Leads: 4
- Weight: 1.7kg
- Length: 66mm
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 32mm
- Shaft Diameter: 12mm
350 RPM 12v DC Planetary Gear Motor – High Torque
Planetary Gear DC Motor with Encoder 12V 435 RPM 2 N-m Torque – TPG36555126000-13.7KE
- Model: TPG36555126000-13.7KE .
- Motor Type: DC Carbon Brush Motor.
- Gear Ratio: 13.7: 1.
- Operating Voltage: 12. V DC
- Rated Current: 0.800.A
- Rated Base Motor: RPM
- Rated Speed: 435 RPM
- Rated Torque: 2N-m
- Operating Temperature: -40 °C ～ +100°C.
- Relative Humidity: 20% ～ 85% RH
- Gear Material: Powder Metallurgy, Steel, POM.
- Housing Material: Metal.
- Motor Body Size (Diameter): 36. mm
- Motor Length: 10.8mm
- Shaft Diameter: 8mm
- Shaft Length: 20mm
- Shaft Type: D-type.
- Motor Weight: 500 gm
- Brushed permanent magnet DC motor.
- Variable speed and reversible.
- Planetary Gear Box.
- Standard brush life of 2000+hours
Planetary Gear DC Motor with Encoder 12V 315 RPM 2.5 N-m Torque – TPG36555126000-19KE
- Model: TPG36555126000-19KE
- Motor Type: DC Carbon Brush Motor.
- Operating Voltage: 12. V DC
- Rated Current: 0.800.A
- Rated Base Motor: RPM
- Rated Speed: 315 RPM
- Rated Torque: 5N-m
- Operating Temperature: -40 °C ～ +100°C.
- Relative Humidity: 20% ～ 85% RH
- Gear Material: Powder Metallurgy, Steel, POM.
- Housing Material: Metal.
- Motor Body Size (Diameter): 36. mm
- Motor Length: 10.8mm
- Shaft Diameter: 8mm
- Shaft Length: 20mm
- Shaft Type: D-type.
- Motor Weight: 500 gm
- Brushed permanent magnet DC motor.
- Variable speed and reversible.
- Planetary Gear Box.
- Standard brush life of 2000+hours
Planetary Gear DC Motor with Encoder 12V 85 RPM 8.5 N-m Torque – TPG36555126000-71KE
- Model: TPG36555126000-71KE
- Motor Type: DC Carbon Brush Motor.
- Gear Ratio: 71 : 1.
- Operating Voltage: 12.V DC
- Rated Current: 0.800.A
- Rated Base Motor: RPM
- Rated Speed: 85 RPM
- Rated Torque: 5 N-m
- Operating Temperature: -40 °C ～ +100°C.
- Relative Humidity: 20% ～ 85% RH
- Gear Material: Powder Metallurgy, Steel, POM.
- Housing Material: Metal.
- Motor Body Size (Diameter): 36.mm
- Motor Length: 11.5mm
- Shaft Diameter: 8mm
- Shaft Length: 20mm
- Shaft Type: D-type.
- Motor Weight: 500 gm
- Brushed permanent magnet DC motor.
- Variable speed and reversible.
- Planetary Gear Box.
- Standard brush life of 2000+hours
Planetary Gear DC Motor with Encoder 12V 11 RPM 10 N-m Torque – TPG36555123000-264KE
• Model: TPG36555123000-264KE
• Motor Type: DC Carbon Brush Motor.
• Gear Ratio: 264: 1.
• Operating Voltage: 12. V DC
• Rated Current: 0.800.A
• Rated Base Motor: 3000.RPM
• Rated Speed: 11 RPM
• Rated Torque: 10 N-m
• Operating Temperature: -40 °C ～ +100°C.
• Opt. Relative Humidity: 20% ～ 85% RH
• Gear Material: Powder Metallurgy, Steel, POM.
• Housing Material: Metal.
• Motor Body Size (Diameter): 36. mm
• Motor Length: 11.5mm
• Shaft Diameter: 8mm
• Shaft Length: 20mm
• Shaft Type: D-type.
• Motor Weight: 500 gm
• Brushed permanent magnet DC motor.
• Variable speed and reversible.
• Planetary Gear Box.
• Standard brush life of 2000+hours
Planetary Gear DC Motor with Encoder 12V 500 RPM 0.5 N-m Torque – TPG28395126000-12KE
- Model: TPG28M395-12K.
- Motor Type: DC Carbon Brush Motor.
- Gear Ratio: 12: 1.
- Operating Voltage: 12.V DC
- Rated Current: 0.750.A
- Rated Base Motor: RPM
- Rated Speed: 500 RPM
- Rated Torque: 5 N-m
- Operating Temperature: -40 °C ～ +100°C.
- Relative Humidity: 20% ～ 85% RH
- Gear Material: Powder Metallurgy, Steel, POM.
- Housing Material: Metal.
- Motor Body Size (Diameter): 28.mm
- Motor Length: 8.8mm
- Shaft Diameter: 6mm
- Shaft Length: 13mm
- Shaft Type: D-type.
- Motor Weight: 230. gm
- Brushed permanent magnet DC motor.
- Variable speed and reversible.
- Planetary Gear Box.
- Standard brush life of 2000+hours
Planetary Gear DC Motor with Encoder 12V 285 RPM 1.2 N-m Torque – TPG28395126000-21KE
- Model: TPG28395126000-21KE
- Motor Type: DC Carbon Brush Motor.
- Gear Ratio: 21: 1.
- Operating Voltage: 12.V DC
- Rated Current: 0.750.A
- Rated Base Motor: RPM
- Rated Speed: 285 RPM
- Rated Torque: 2 N-m
- Operating Temperature: -40 °C ～ +100°C.
- Relative Humidity: 20% ～ 85% RH
- Gear Material: Powder Metallurgy, Steel, POM.
- Housing Material: Metal.
- Motor Body Size (Diameter): 28.mm
- Motor Length: 8.8mm
- Shaft Diameter: 6mm
- Shaft Length: 13mm
- Shaft Type: D-type.
- Motor Weight: 230. gm
- Brushed permanent magnet DC motor.
- Variable speed and reversible.
- Planetary Gear Box.
- Standard brush life of 2000+
Planetary Gear DC Motor with Encoder 12V 115 RPM 2.5 N-m Torque – TPG28395126000-52KE
- Model: TPG28M395-52K.
- Motor Type: DC Carbon Brush Motor.
- Gear Ratio: 52: 1.
- Operating Voltage: 12.V DC
- Rated Current: 0.750.A
- Rated Speed: 115 RPM
- Rated Torque: 2.5 N-m
- Operating Temperature: -40 °C ～ +100°C.
- Relative Humidity: 20% ～ 85% RH
- Gear Material: Powder Metallurgy, Steel, POM.
- Housing Material: Metal.
- Motor Body Size (Diameter): 28.mm
- Motor Length: 8.8mm
- Shaft Diameter: 6mm
- Shaft Length: 13mm
- Shaft Type: D-type.
- Motor Weight: 230. gm
- Brushed permanent magnet DC motor.
- Variable speed and reversible.
- Planetary Gear Box.
- Standard brush life of 2000+