3DR Single TTL MINI Radio Telemetry 433MHz 250mW for PIXHAWK and APM
- MAVLink protocol framing status documents.
- Frequency modulation and Spread Spectrum (FHSS).
- Self-adaption to time-division multiplexing.
- Support LBT and AFA.
- Configurable duty cycle.
- Built-in error correcting code(up to 25% data bit error).
- AT command configures data transmission.
- RT command remote control data transmission.
- Interchangeable air and ground 433MHz modules.
- Micro-USB port.
- 6-position Molex connector.
- 250mW maximum output power (adjustable).
- SMA connector.
- 2-way full-duplex communication through adaptive TDM.
- UART interface.
- Transparent serial link.
- Open-source SIK firmware.
- Configurable through *Mission Planner and *APM Planner.
- Featuring a SiLabs Si1000 RF Microcontroller
- Support OTG of Android Cellphone and Compute
- Based on the Hope RF HM-TRP radio Module,
433mHz Transmitter Receiver RF Radio Module
- Range in open space(Standard Conditions) : 100 Meters
- RX Receiver Frequency: 433 MHz
- RX Typical Sensitivity: 105 Dbm
- RX Supply Current: 3.5 mA
- RX IF Frequency: 1MHz
- RX Operating Voltage: 5V
- TX Frequency Range: 433.92 MHz
- TX Supply Voltage: 3V ~ 6V
- TX Output Power: 4 ~ 12 Dbm
- Low Power Consumption
- Easy For RF-based Application
- Complete Radio Transmitter
- Transmit Range Up To 50m
- CMOS / TTL Input
- No Adjustable Components
- Very Stable Operating Frequency
- Low Current Consumption (Typ 11mA)
- Wide Operating Voltage
- ASK Modulation
434MHz/315Mz TX & RX
Transmitter
- Working voltage: 3V - 12V for max. power use 12V
- Working current: max Less than 40mA max , and min 9mA
- Modulation mode: ASK
- Working frequency: 433MHz
- Transmission power: 25mW
Receiver
- Working voltage: 5.0VDC
- Working current:≤5.5mA max
- Modulation method: OOK/ASK
- Working frequency: 433.92MHz
- Bandwidth: 2MHz
- Sensitivity: excel –100dBm (50Ω)
- Transmitting velocity: <9.6Kbps (at 315MHz and -95dBm)
Antenna GSM-2DBI (Spring)
- Gain: 2dBi
- Lower VSWR ≤ 2.0
- Signal stability.
- Cable Length: 3m
- Antenna Height: 28cm
- Polarization Vertical Impedance- 50 Ω
- Material: Metal
- Colour: Black
- Operation Temperature: -30~60 degree C
- Humidity: 5% to 95%
- Connector type: SMA Male Plug
- Compact size.
- Good appearance.
- Strong adaptability of environment.
- Package includes:
Antenna GSM-6DBI (Spring)
- Gain:6dBi
- Lower VSWR ≤ 2.0
- Signal stability.
- Cable Length: 3m
- Antenna Height: 28cm
- Polarization Vertical Impedance- 50 Ω
- Material: Metal
- Colour: Black
- Magnetic base
- Operation Temperature: -30~60 degree C
- Humidity: 5% to 95%
- Connector type: SMA Male Plug
- Compact size.
- Good appearance.
- Strong adaptability of environment.
Anti Spy Cell Phone Signal Bug Rf Camera GSM Device Detector 2600Mhz
- Colour: Black
- Detecting frequency: 100 - 2600mhz
- Effective range: 1-10m (32 - 32ft)
- Detect the harmful electromagnetic radiation
- Detect if there is more secret 5. 8 Ghz wireless web camera, wireless wiretap, and wire monitor.
- Ensure the privacy of your phone conversations up to a great extent
- Prevents eavesdropping, videotaping, fraud, protect personal privacy data and information confidential
- Dimensions:6*5*5cm
- Weight: 400gm
Generic SIM900 GPRS/GSM Development Extension Board Shield Quad-Band Kit for Arduino
- Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world.
- GPRS multi-slot class 10/8
- GPRS mobile station class B
- Compliant to GSM phase 2/2+
- Class 4 (2 W @ 850 / 900 MHz)
- Class 1 (1 W @ 1800 / 1900MHz)
- Control via AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands.
- Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).
- Embedded TCP/UDP stack - allows you to upload data to a web server.
- RTC supported.
- Selectable serial port.
- Speaker and Headphone jacks
- Low power consumption - 1.5mA(sleep mode)
- Industrial Temperature Range - -40°C to +85 °C
GPS 3V Mount SMA-3M Cable
- Central Frequency: 1575.42 MHz /GPS External Active Antenna- 2 MHz
- Polarization: R.H.C.P
- Input Voltage: 3 V to 5 V
- Gain: 27 dB / 01 dB
- Embedded Magnet for easy mounting
- Water-Proof Design
- 5 M Cable with SMA Connector
- Operating Temperature: 20 to 85 degree C
- Bandwidth (min.): 9 MHz
- Storage Temperature: 50 to 120 degree C
- Relative Humidity: 0 % to 100 %Transmitter & Receiver
GPS Antenna Mount Folding Bracket Anodized Aluminum Carbon for M8N GPS MODULE APM PixHawk
- Material: CNC Aluminium alloy, carbon glass fiber rod
- Mounting rod diameter: 4mm
- Lead of rod: 14 cm. GPS plate diameter: 40 mm.
- Base plate diameter: 35 mm
- Mounting hole spacing: 16mm
- Easy to assemble.
- Lightweight so doesn't create unsuitability while operating
- Usage: Multicopter YS X4 X6 DJI Other
- Dimension:12cm x 10cm x 10cm
GPS Modem SKG13C External Antenna
- Operating voltage: 3.0V to 4.2V
- Ultra high sensitivity: -165dBm
- Extremely fast TTFF (Time To First Fix) at the low signal level
- Low power consumption: Typical [email protected]
- NMEA-0183 compliant protocol or custom protocol
- Operating temperature range: -40 to 85℃
- SMD type with stamp holes
- Small form factor: 15x13x2.7mm
- RoHS compliant (Lead-free)
- Support walk model
GPS Modem with External Antenna
- SiRF Star IVâ„¢, GSD4e ROM version
- Tracking sensitivity -163dBm, autonomous Acquisition sensitivity -148dBm
- TTL interface output
- 48 track verification channels
- Power supply 3.3 voltage
- SMT type with stamp holes
- Small form factor with embedded SiRF star iv technology
- Removes in-band jumbers up to 80dB-Hz, track up to 8CW jammers
- Excellent sensitivity for urban canyon and foliage environments.
GSM GPRS + Camera Module A6C Breakout
- Operating Voltage: 3.3V – 4.2V
- Working Temperature: -30 ℃ to +80℃
- Boot Voltage: >3.4V
- Standby Current: less than 3 mA
- GSM/GPRS Frequency Band: including 850, 900, 1800, 1900 MHZ
- GPRS Class 10
- Sensibility: <-105
- Voice Call: Support
- SMS message: Support
- GPRS maximum speed: Download speed 85.6Kbps, Upload speed 42.8Kbps
- AT Command: Support standard GSM07.07, 07.05, and extended Ai Thinker command
- 2 UART: one for download, one for AT command
- Audio: Support digital and analog audio, support HR, FR, EFR, AMR audio code
- Camera resolution: 0.3M
GSM Modem SIM 300
- Uses SIM300 GSM module transmission.
- Operating Voltage: 7 – 15V AC or DC (board has onboard rectifier).
- Comes with an onboard wire antenna for better reception.
- Can be used for Data/Fax, GSM based Voice communications, TCP/IP stack, GPRS and SMS
- SIM300 allows an adjustable serial baud rate from 1200 to 115200 bps (9600 default).
- Provides RS232 interface for connection to computers and other devices.
- Lithium Battery holder
- Can add external antenna with SMA connectors.
- Power, RING and Network LEDs for easy debugging.
- Provides serial TTL interface for easy and direct interface to microcontrollers.
- Can be controlled through standard AT commands.
GSM Modem Sim900
- Quad-Band GSM/ 850/900/1800/1900MHz
- Voice Communication Port
- On-Board Voltage Regulator
- Power/Single LED indication
- SMA Connector for Antenna connection
- Compatible with Arduino, raspberry pi, arm, avr, pic, 8051
- Power Supply 12v 1amp to 2 amps max
- Use in the area of full signal strength.
- Perfectly suited for GSM-based Microcontroller Projects (better than SIM300 and other GSM Modems)
- Option for connecting MIC and SPEAKER directly to GSM MODEM for calls (LINE IN also available)
- Supports communication through RS232 with DB9 Connector, TTL Pins and I2C Pins
- CALL SMS GPRS facility - MIC input, LINE input and SPEAKER output pinsX
GSM/GPRS/GPS SIM 808 IOT Modem
- Input voltage: 5V-12V DC Operation
- Working temperature:-40°C ~85°C
- Supply voltage range 3.4 ~ 4.4V
- Low power consumption
- Operation temperature:-40°C ~85°C
- Power supply: 3.4V ~ 4.4V
- Charging: Supports charging control for Li-Ion battery
- Quad-band 850/900/1800/1900MHz
- GPRS multi-slot class 12/10
- GPRS mobile station class B
- Compliant to GSM phase 2/2+ – Class 4 (2 W @ 850/900MHz) – Class 1 (1 W @ 1800/1900MHz)
- Dimensions: 24*24*2.6mm
- Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT Commands)
- Modem with Impedance Matching Layout.
- Fully Automatic Pick and Place Machine.
- On-board SMA connector for GSM antenna
- On-board UFL connector for External GSM Antenna
- On-board SMA & UFL connector for GPS Antenna
- Option to Connect Patch antenna or Active Antenna for GPS
- Onboard 3V3 Voltage regulator for GPS External Active Antenna
- Onboard Micro USB Connector for module firmware updation
- Automatic and Manual Start option (SMD Switch has provided for Manual Startup)
- LM39302 linear voltage regulator is used for provides a low-dropout, high-current output
- Onboard RMC connector for power supply
- Onboard RMC connector for audio interface
- On-board Connector for connecting 3.7V Li-Po battery
- Zener diode is used to prevent Accidental over voltage
- On board TXB0104 voltage level translator IC which helps us to interface with 2.8V to 5V microcontrollers’
- On board LED for power indication, Network and status.
- Header option for interfacing ADC, I2c,PWM
- Four 3MM Mounting Holes are Provided
- Flap Type SIM Card Connector
- On-board Anti-Static Protection IC
- Easy to Make and receive voice calls, Send and receive SMS messages
Mini SMD NRF24L01 2.4G Wireless Data Transmission Module
- Maximum operating speeds up to 2Mbps
- GFSK modulation efficiency, Anti-interference ability,
- Built-in hardware CRC error detection, Multipoint communication address control.
- Low-power 1.9 to 3.6V, only 1uA on Power-down mode
- Built-in 2.4Ghz antenna
- Built-in voltage regulator
- 125 Channels, Multi-point communication, and frequency hopping to meet the communication needs
- Wireless transceiver including Frequency generator, enhanced type, SchockBurstTM, mode controller, power amplifier, crystal amplifier, modulator, demodulator
- The output power channel selection and protocol settings can be set extremely low current consumption, through the SPI interface
- In the transmit mode, the transmit power is 6dBm, the current is 9.0mA, the accepted mode current is 12.3mA, the current consumption of the power-down mode and standby mode are lower
- Standard DIP Pitch Interface for embedded applications.NRF24L01 SPI interface: hardware SPI port, MCU I/O ports
- Internal FIFO compatible with a variety of microprocessor interface, micro-controller is convenient
NRF24L01 Long Range
- Voltage: 3-3.6V (recommended 3.3V) V.
- Maximum output power: +20dBm.
- Power-down mode current: 4.2uA.
- Operating Range: 1Km.
- Transmission mode current(peak): 115mA
- Receiver Mode Current(peak): 45mA
- Power-down mode current: 4.2uA
- Sensitivity 2Mbps mode in received: -92dBm
- It uses 2.4GHz global open ISM band, with license free.
- SPI interface facilitates the communication with MCU I/O port.
- Support six-channel data reception.
- 2Mbit/s speed makes high-quality VoIP possible
- Multi-frequency points: 125 frequency points meet the needs of multi-point communications and frequency hopping.
- Supports 126 RF channels
- Onboard antenna for optimum performance
- Standard DIP type pinout for easy Interface through jumper wires or breadboard
- Small size: 16.5mm*45.5mm.
RF 433Mhz RX TX Encoder Decoder board [HT12E & HT12D IC]
- Operating voltage: 3.6~5.5v ( 5v recommended),
- Receiver sensitivity as high as -110dbm,
- Compatible with HT12E and HT12D,
- Low power and good range.
- High-frequency stability and low coherence and interference
- Easy interfacing with the RF modules, using the female headers for placing the modules.
- Breakout pins for connecting to the microcontroller.
- DIP Switch for Address Selection (when multiple modules are used at one location)
- Status LED for valid transmit.
- Supports both ASK, FSK RF modules
- Small size, high quality PCB.
RF Transmitter Receiver Module 315MHz Wireless
Transmitter Module
- Operating voltage: 3V to 12V
- Operating frequency: 433.92MHz; 315MHz
- Standby current: 0mA
- Operating current: 20mA to 28mA
- Transmission distance: >500m (open to receiving plate sensitivity at -103dBm distance of more than)
- Output power: 16dBm (40mW)
- Data transfer rate: <10Kbps
- Modulation mode: OOK (amplitude modulation)
- Operating temperature: -10℃ to +70℃
-
- Operating voltage: 5V DC
- Static current:4mA
- Receiver frequency: 433.92MHz; 315MHz
- Sensitivity: -105dB
- External antenna: 32CM single wire spiral
- No of pins: 4
SIM28 GPS Module / Modem with GPS antenna
- Operating voltage: 12v dc.
- Compatible with TTL & serial.
- Frequency 1, 1575.42mhz
- 023mhz chip rate
- 16 channels all in view
- 6-channels GPS search engine
- Ultra-low-power design (38mA, typical)
- Compact size
- Built-in low noise, high gain active antenna
- Super-cohesive magnetic for installation
- High sensitivity (up to -152dBm typ)
- Apply to host devices with USB or RS232
SIM900A 5V V4.0 Kit Wireless Extension Module GSM GPRS Board Antenna Tested
Ublox NEO 7M GPS With Compass for APM 2.6/2.8 and Pixhawk 2.4.6/2.4.8
- Tracking sensitivity: 161 dBm
- Capture sensitivity : 148 dBm
- Cold start time: 38s average
- Warm start time: 35s average
- Hot start time: 1s average
- Capture time: 0.1s Average
- Locate performance
- Pre-configured, Flashed with the correct settings and tested
- Super Bright LED
- Backplane with Standard Mk style mounting holes 45mm X 45mm
- 38400 bps (Default) Changed to 115200bps!
- Output GGA, GSA and RMC frames
- 1Hz (Default) Changed to 5Hz!
- Permanent Configuration Retention
- Onboard compass
- 6 pin connector for EZ connect to MEGA BLACK
- 4 pin connector for only GPS use
- 4 pin connector for compass only use
- Can use both 4 pin at once
Ublox NEO-M8N GPS Module with Compass for APM with extra connector for Pixhawk
- Ready to Connect to All APM FC with 5-pin connector Attached
- Receiver type 72-channel M8 engine
- Galileo-ready E1B/C (NEO-M8N)
- update rate1 Single GNSS: up to 18 HZ
- Position accuracy 22.0 m CEP
- Acquisition2 Cold starts: 26 s
- Sensitivity2 Tracking & Nav: –167 dBm
- On-board Compass
- Dimensions: Outer diameter 54mm
- GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1.
- SBAS L1 C/A: WAAS, EGNOS, MSAS.
- Assistance AssistNow GNSS Online.
- Assist Now GNSS Offline (up to 35 days)3.
- Assist Now Autonomous (up to 6 days).
- OMA SUPL & 3GPP compliant
- Oscillator TCXO (NEO-M8N/Q).
- Crystal (NEO-M8M).
- RTC crystal Built-In.
- Noise figure On-chip LNA (NEO-M8M). Extra LNA for.
- Lowest noise figure (NEO-M8N/Q).
- Anti-jamming Active CW detection and removal.
- Extra onboard SAW bandpass filter (NEO-M8N/Q).
- Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N).
- Supported antennas Active and passive.
- Odometer Travelled distance.
- Data-logger For position, velocity, and time (NEO-M8N).
- Weight 33gm