IMAX B6-AC Lipo NiMH Battery Charger/Discharger 1-6 Cells
- AC Input Voltage: 100V ~ 240v or 12V DC input
- Current: 2.5A Max.
- Max Charge: 50W
- Max Discharge: 5W
- Charge Current Range: 0.1A ~ 6.0A
- Discharge Current Range: 0.1~1.0A NiMH/NiCd Cells, 1~15A LiIon/LiPoly Cells 1~6A Pb
- Plug Type: Female End Type: IEC(To Charger)
- Plug Type. Male End Type: EU plug (To Power Distribution Board).
- The cables come with a fitted fuse.
- Microprocessor controlled
- Li-ion, LIPO, and LiFe are capable
- Input voltage monitoring. (Protects car batteries at the field)
- Battery break-in and cycling feature
- Data storage (Store up to 5 packs in memory)
- Internal resistance checker to see pack health
- Delta-peak sensitivity
- Individual cell balancing
- EU Plug to IEC C13 which is used in devices such as ac adapters, digital cameras, camcorders, monitors, printers, Direct TV and more!\
- Dimensions: 135 x 144 x 36mm
- Weight: 632g
IMAX B6 DIGITAL RC LIPO NiMH BATTERY BALANCE CHARGER
- Input Voltage: 11V to 18V
- Battery Voltage: 2V to 20V
- Power Max Charge: 50W – Max
- Discharge: 5W
- Charge Current Range: 0.1 to 5.0A
- Discharge Current Range: 0.1~1.0A NiMH/NiCd Cells, 1~15A LiIon/LiPoly Cells, 1~6A Pb
- Microprocessor controlled
- LiIon, LiPoly, and LiFe are capable
- NiCad and NiMH are capable
- Large range of charge currents
- Storage charge function
- Time limit function
- Delta-peak sensitivity
- Individual cell balancing
- Battery break in and cycling.
- Input voltage monitoring (Protects car batteries at the field)
- Data storage (Store up to 5 packs in its memory
- Dimensions: 133x87x33m
- Weight 277g
HK-300 (2.5W) submersible mini water pump AC 220V-240V
HSS DRILL BIT SET
9*15cm PERFBOARD
7*9cm PERFBOARD
PCB 12*18 cm
RIBBON CABLE
MOQ : 1 m
- Rate temperature: 105°C
- Rated voltage: 300V
- Average tensile strength: 1500 lbs
- Spark test: 2500V
- Dielectric strength test: Minimum 2 KV in 1 minute
- Conductor resistance: Maximum 237Ω/km
- Insulation resistance: Minimum 100 MΩ-km
- Capacity: 44pF/m (G-S-G)
- Inductance: 1.45μH/m
- Characteristic Impedance: 105Ω (G-S-G)
- Propagation delay time: 4.2 ns/m
- Â Durable and reusable
- Easy to install and use
- A popular choice for construction or repair
- Useful for the electronic project and Genuine Arduino product
XL4015 5A STEP DOWN WITH DISPLAY
- Module nature: non-isolated buck module ( BUCK )
- Input voltage: 4-38V
- Output voltage: 1.25-36V
- Output current: 0-5A, it is recommended to use within 4.5A
- 14 Digital I/O Pins
- Output power: It is recommended to use within 75W, please add a heat sink if it exceeds 50W
- Working temperature: -40 degree to + 85 degrees
- Working frequency: 180KHz
- Conversion efficiency: up to 96% Load adjustment rate: S ( I ) ≤ 0.8%
- Voltage adjustment rate: S ( u ) ≤ 0.8%
- LED to indicate power status
- Short circuit protection
- Over-temperature protection
- Dimension: 54mm * 23mm wide *18mm
XL4015 5A STEP DOWN MODULE
- Module nature: non-isolated buck module ( BUCK )
- Input voltage: 4-38V
- Output voltage: 1.25-36V
- Output current: 0-5A, it is recommended to use within 4.5A
- 14 Digital I/O Pins
- Output power: It is recommended to use within 75W, please add a heat sink if it exceeds 50W
- Working temperature: -40 ~ + 85 degrees
- Working frequency: 180KHz
- Conversion efficiency: up to 96% Load adjustment rate: S ( I ) ≤ 0.8%
- Voltage adjustment rate: S ( u ) ≤ 0.8%
- Power indicator: No
- Short circuit protection
- Over-temperature protection
- Dimension: 54mm * 23mm wide *18mm
WS2812 LED BREAKOUT BOARD
- Input Voltage: -0.5～VDD+0.5V
- Supply voltage: 5v
- Operating voltage: 4v -7v
- Integrating control circuit and RGB chip
- Built-in signal reshaping circuit
- Built-in electric reset circuit and power lost reset circuit
- 256 brightness and 16777216 colour display
- Viewing angle: 120 degree
- Cascading port transmission signal
- Red Vf: 1.8~2.2V
- Green Vf: 3.0~3.2v
- Blue Vf: 3.2~3.4V
- Red Wavelength: 620~630 nm
- Green Wavelength: 515~530 nm
- Blue Wavelength: 465~475 nm
- Red luminous intensity(20mA): 550~700mcd
- Green luminous intensity(20mA): 1100~1400mcd
- Blue luminous intensity(20mA): 200~400mcd
- Dimension: 1.8*1.3*0.8mm
USBASP PROGRAMMER
- No special USB controller required
- Programming speed is up to 5Kbytes/sec
- Working platform: Linux, Windows, Mac OS X
- Allows to read or write the microcontroller EEPROM, firmware, fuse bits, and lock bits
- No special controllers or SMD components are needed.
- Target is supported by the SCK option with a low clock speed (<1.5MHz)
- Programming status and Bus status are easily identified
- The easy interface is achieved by Header pins for various ISP header pins
- Dimension: 63.3*20.5*10.5mm
- Weight: 15gm