Leadshine DMA860H

₹8,500.00 inc. GST
  • Input voltage: Up to +80VAC or +110VDC.
  • Output current Up to 7.2A.
  • Pulse input frequency up to 300 KHz.
  • Automatic idle-current reduction.
  • Over-voltage, over-current protection.
  • Suitable for 2-phase and 4-phase motors.
  • Support PUL/DIR and CW/CCW modes.
  • Operating Temperature : 70 C.
  • High performance, cost-effective
  • Self-adjustment technology
  • Pure-sinusoidal current control technology
  • TTL compatible and optically isolated input
  • 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
 

Leadshine DMA860E Stepper Motor Driver

₹5,700.00 inc. GST
  • Model: DMA860E.
  • Control Mode: Step & Direction.
  • Max Input Frequency: 200 kHz.
  • Input Voltage Range: 18 - 80 VAC / 24 - 110 VDC.
  • Suggested Power Supply Voltage Range: 36-90 VDC /24-60 VAC.
  • Number of DIP Switch Resolution Configurations: 16.
  • 16 selectable micro-step resolutions of 400-51,200 via DIP switches.
  • 8 selectable output current settings of 2.4 – 7.2A via DIP switches.
  • Logic Current Range: 7-16mA (10mA typical).
  • Logic Voltage Range: 4-5 VDC for pulse active high (default), or 0-0.5V for pulse active low.
  • Pulse enabled at: Rising edge.
  • Idle Current Percentage: 50 %.
  • Number of Digital Inputs: 3.
  • Step Width: 2,500 ns.
  • Minimal Direction Setup Time: 5,000 ns.
  • Isolation Resistance: 500M Ohm..
  • Ambient Temperature: 0-50°C.
  • Humidity: 40–95% RH.
  • Operating Temperature: 0-70°C.
  • Vibration: 5.9 m/s2 Max.
  • Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors.
  • Step & direction (PUL/DIR) and CW/CCW (via internal jumper set) control. Step & direction by default Multi-Stepping for smooth motor movement.
  • Opto Isolation for input control signals.
  • Soft-start with no “jump” when powered on.
  • Protections for over-voltage and over-current.
  • Dimension: 5.94 X 3.82 X 2.24 Inches.
  • Weight: 1.13 lbs.
   

Leadshine DM320C

₹5,500.00 inc. GST
  • Supply voltage up to +30 VDC
  • Output current programmable, from 0.3A to 2.0A
  • Pulse input frequency up to 70 kHz
  • TTL compatible and optically isolated input
  • Automatic idle-current reduction
  • Suitable for 2-phase and 4-phase motors
  • Support PUL/DIR and CW/CCW modes
  • Over-voltage, over-current, phase-error protection
  • Anti-Resonance provides optimum torque and nulls mid-range instability
  • Self-test and Auto-configuration technology offers optimum responses with different motors
  • Microstep resolutions programmable, from full-step to 102,400 steps/rev
  • Support PUL/DIR and CW/CCW modes
  • Over-voltage, over-current, phase-error protection
  • Its unique features make the DM320C an ideal solution for applications that require low-speed smoothness

Leadshine DM542

₹4,500.00 inc. GST
  • Good high-speed performance
  • Supply voltage up to +50VDC
  • Output current up to 4.2A
  • Pulse frequency up to 300 KHz
  • Extremely cost-effective
  • Automatic idle-current reduction
  • 3-state current control technology
  • Self-adjustment technology
  • Pure-sinusoidal current control technology
  • TTL compatible and optically isolated input
  • 15 selectable resolutions in decimal and binary, up to 25,600 steps/rev
  • Suitable for 2-phase and 4-phase motors
  • DIP switch current setting with 8 different values
  • Support PUL/DIR and CW/CCW modes
  • Short-voltage, over-voltage, over-current protection

DM556 Digital Stepper Motor Driver with Micro Stepping 20 to 50V 5.6A

₹4,000.00 inc. GST
  • Good high-speed performance
  • Supply voltage: +50VDC
  • Output current from 0.5A to 5.6A
  • Pulse input frequency up to 200 kHz
  • Extremely cost-effective
  • Automatic idle-current reduction
  • Self-test and Auto-configuration technology TTL compatible and optically isolated input
  • Micro step resolutions programmable, from full-step to 102,400 steps/rev
  • Suitable for 2-phase and 4-phase motors
  • Support PUL/DIR and CW/CCW modes
  • Anti-Resonance provides optimum torque and nulls mid-range instability
  • Extra-low motor noise offers excellent quietness
  • Over-voltage, over-current protection and phase error protection

BM1418ZXF 48V 750W Controller for Brushless DC Motor

₹3,900.00 inc. GST
  • Rated Voltage: 48V.
  • Rated Output Power: 750W
  • Speed after Reduction: 480 RPM
  • Rated Speed: 2800 RPM
  • Gear Ratio: 1:6
  • Throttle: 1-4V.
  • Full Load Current: 20A
  • No Load Current: 5A
  • Rated Torque: 15.36 N.m.
  • Load Capacity: Up to 350 KG
  • Small and Medium-size E-Tricycle
  • Short voltage protection: 31.5±0.5V/42±0.5V.
  • Colour: silver.
  • Casing material: Aluminium.
  • Dimension: 105 x 65 x 32mm

Controller for BM1418ZXF 48V 350W for Brushless DC Motor

₹3,100.00 inc. GST
  • Rated Output Power - 350W
  • Rated Voltage - 48V
  • DC Speed after Reduction - 480
  • RPM Rated Speed - 2800
  • RPM Gear Ratio - 1:6
  • Full Load Current - 9.4A
  • No Load Current - 2.8A
  • Rated Torque - 7.2 N.m.
  • Application - Small and Medium size E-Tricycle

48v 500W BM1418ZXF Motor Controller

₹2,800.00 inc. GST
  • Rated Voltage: 48 Volt DC.
  • Rated Power: 500W.
  • Maximum Current: 30 Amps.
  • Level Brake: low.
  • Current limited: 30A±0.5A.
  • Efficiency: ≥83%.
  • Consumption: <1.5W.
  • Turn The Voltage: 1-4.2V.
  • Phase Angle: 120 degrees.
  • Includes attachments for motor, accelerator, brake, battery, battery charging, brake light, power lock

VNH2SP30 – Monster Moto Shield 30A Mini Stepper Motor Driver

₹2,200.00 inc. GST
  • Driver Model: Monster Moto Shield VNH2SP30
  • Operating Voltage: 12V to 16V DC
  • Maximum current rating: 30 A
  • Continuous Current: 14 A
  • Number of Channels: 1
  • MOSFET on-resistance: 19 m (per leg)
  • Maximum PWM frequency: 20 kHz
  • Current sensing available to Arduino analog pin
  • Thermal Shutdown
  • Under voltage and Overvoltage shutdown.
  • Dimensions: 55 x 28 x 12mm
  • Weight: 15gm

5V-12V DC Brushless Motor Driver Board Controller

₹1,999.00 inc. GST
  • Type: Voltage Regulator
  • Drive voltage: DC 5-l2V
  • Work current: ≤ 1.2A
  • Speed range: from 0% to 100%
  • Phase inversion Control
  • Offers Voltage polarity protection and Overcurrent Protection
  • Suitable for hard brushless motor, brushless motor drive and other miniature 3 / 4 wire brushless motor without hall

MACH3 interface board

₹1,350.00 inc. GST
  • Compatible Stepper Motor Driver - Max 5 2-phase Microstep controllers
  • Driver type - Pulse and Direction signal control
  • Wide input voltage range: 12-24V, and with anti-reverse function.
  • Output 0-10V analogue voltage for the inverter to control the spindle speed.
  • Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
  • USB power supply and peripherals power phase are separate to protect computer security.
  • All the signals are to-isolate which can protect your computer security.
  • 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
  • Wide input voltage range: 12-24V, and with anti-reverse function.
  • One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
  • Maximum support 5-axis stepper motor driver controllers
  • Output 0-10V analogue voltage for the inverter to control the spindle speed.
  • All the way to the relay output port, control spindle switch. Output port P17 mouth.
  • One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
  • Weight - Approx. 75g
  • Dimensions - 90 * 70 * 20mm

TB6560 CNC 3 Axis Stepper Motor Driver Controller Board

₹970.00 inc. GST