I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Flex Sensor 4.5”
₹1,100.00 Original price was: ₹1,100.00.₹1,000.00Current price is: ₹1,000.00. inc. GST
- Operating voltage: 0-5V
- Power rating: 0.5Watt (continuous), 1 Watt (peak)
- Life>1 million
- Flat Resistance: 10K Ω
- Resistance Tolerance: ±30%
- Bend Resistance Range: 60K to 110KOhms(depending on the bend)
- Total Length: 4.5″
- Bends and Flexes physically with the motion device.
- Simple Construction.
- Dimension:11*1*5cm
- Weight: 400gm
The flex sensor is defined as a bend detecting sensor, one of the prominent sensors that have got numerous applications in robotics, medical, and haptic technology. These are variable resistance in which the resistance of sensors changes in accordance with the bend, which can be measured using any microcontroller. In short, this is a flexible sensor that changes its output when it is bent or when force is applied to it. Hence also works as a Force sensor. The Flex sensor provides an active sensing area of 10cm with a flex resistance of 10K Ω and a length of 4.5inch. A connector of 0.1″ spaced used and breadboard-friendly makes the installation easier.
This sensor provides two output wires. As the sensor flexed or bend, the resistance between these two wires increased. It should be considered that the base of the sensor is sensitive to bending and may get damaged. Hence care should be taken that you bend only the sensing area. For best results, securely mount the base and bottom portion and only allow the actual flex sensor to flex.
During nominal resistance, the surface of the Flex sensor is completely linear. When it bents 45º angle the Flex Sensor resistance increases to twice as before. And when bents 90º the resistance varies as high as four times than the nominal resistance. As a result, the resistance across the terminals rises linearly with a bent angle. So in short the flex sensor converts flex angle to resistance parameter. For better convenience, we convert this resistance parameter to a voltage parameter using a voltage divider circuit. This voltage parameter is fed into ADC for digital output.

Related products
LDR SENSOR 20mm
LJ12A3-4-Z/BY PNP DC6-36V 8 mm INDUCTIVE PROXIMITY SENSOR
- Output type: PNP NO
- Supply voltage: 6V-36V
- Current output: 300mA
- Response frequency: 0.5khz
- Detecting distance: 4mm
- Wire type: cylindrical DC 3 wire type
- Switch appearance type: cylinder type
- Operating temperature: -25 degrees to 55 degrees Celsius
- Detect object: iron
- Red led checks proximity status
- High repeated positioning accuracy
- High switching frequency
- Reverse power protection, short circuit protection, directly connecting with PLC
- anti-vibration, dust, water, and oil prevention
- Dimension: 5*3*3cm
- Weight: 400gm
MQ2 Sensor
- Operating Voltage: +5V
- Can be used to Measure or detect LPG, Alcohol, Propane, Hydrogen, CO, and even methane
- Analogue output voltage: 0V to 5V
- Digital Output Voltage: 0V or 5V (TTL Logic)
- Preheat duration 20 seconds
- Can be used as a digital or analogue sensor
- Load resistance: 20 KΩ
- Heater resistance: 33Ω ± 5%
- Heating consumption: <800mw
- Sensing Resistance: 10 KΩ – 60 KΩ
- Detection range: 200 – 10000ppm
- Preheat Time: Over 24 hour
- High sensitivity to LPG, Propane, and Hydrogen
- The Sensitivity of a Digital pin can be varied using the potentiometer
MQ3 Sensor
- Operating Voltage: 5V ±0.1
- Detecting Concentration: 0.05-10mg/L Alcohol
- Current Consumption : 150mA
- Operation Temperature : -10°C ~ 70°C
- Heater consumption: less than 900mW
- Load resistance: Adjustable
- Heating resistance: 33Ω ± 5%
- Easy SIP header interface
- Compatible with most of the microcontrollers
- Low-power standby mode
- Requires heater voltage
- Good sensitivity to alcohol gas
- Fast response and High sensitivity
- Requires simple Drive circuit
- Dimensions: 32 x 22 x 16 mm
MQ7 GAS SENSOR
- Operating Voltage: 3.3 – 5V.
- Type: Analog Sensor.
- Can detect the presence of carbon monoxide
- Heating voltage (high): 5V ± 0.1
- Heating voltage (low): 1.4V ± 0.1
- Load resistance: Adjustable
- Heating resistance: 33Ω ± 5%
- Heating time (high): 60 ± 1 seconds
- Heating time (low): 90 ± 1 seconds
- Heating consumption: About 350mW
- Using temperature: -20°C-50°C
- Storage temperature: -20°C-50°C
- Relative humidity: Less than 95%RH
- Oxygen concentration: 21%(stand condition) the oxygen concentration can affect the sensitivity characteristic
- Stable, long life and low cost
- Good sensitivity to Combustible gas in a wide range
PIEZO Vibration Sensor
- Flexible PVDF Piezo Polymer Film
- Flex, Touch, Vibration and Shock measurements
- Voltage Sensitivity (open-circuit, baseline): 1.1 V/g.
- Charge Sensitivity (baseline): 260 pC/g.
- Upper Limiting Frequency (+3 dB): 42 Hz.
- Resonance Frequency: 75 Hz.
- Voltage Sensitivity (open-circuit, at resonance): 6 V/g.
- Wide dynamic range:001Hz~1000MHz
- Laminated for higher voltage output
- Breadboard friendly leads.
- Standard grove socket
- Adjustable sensitivity
- Withstands High Impact
- Operating Temperature: 0ºC to 85ºC
- Storage Temperature: -40ºC to 85 ºC
- Dimensions: 6.9 x 3.9 x 0.8 cm
- Weight: 10 Grams
TCRT5000
- Model TCRT5000
- Colour: Black + blue
- Operating Voltage Range: 3.6~5 VDC
- Package type: leaded
- Typical output current under test: IC = 1 mA
- Emitter wavelength: 950 nm
- Peak operating distance: 2.5 mm
- Detecting range: 0.591″ (15mm)
- Detecting method: Reflective
- Collector-Emitter: Voltage: 70V
- Collector Current: 100mA
- Forward Current: 60mA
- Output type: Phototransistor
- Lead (Pb)-free soldering released
- Daylight blocking filter
- Dimensions: 10.2 x 5.8 x 7mm
U Slot Sensor MOC7811
- Model HY860D
- Output Type Photo Transistor
- Peak Emission Wavelength: 940nm
- IR Diode Forward Current: 50mA
- IR Diode Reverse Voltage: 5V
- Transistor Power Dissipation: 75mW
- Transistor Collector Current: 20mA
- Photo Transistor Collector-emitter Voltage: 30V
- Photo Transistor Emitter-collector Voltage: 5V
- Diode Power Dissipation: 100mW
- Operating Temperature Range: -55~100 Celsius Degree
- Number of Pins 4
- Hole Diameter: 3mm
- Material: Plastic, Metal
- Non-Contact Switching
- For Direct PC-Board or Dual-In-Line Socket Mounting
- Fast Switching Speed
- Colour: Black
- Dimension: 22 x 22 x 6mm
- Weight: 8gm

Reviews
There are no reviews yet.