Showing 1–12 of 19 results

AVR ISP 10 Pin to 6 Pin Adapter Board

175.00 inc. GST
  • Made of high-quality material, practical and durable
  • No. of Pinon USBASP side: 10.
  • Connector type on USBASP side: Male.
  • No. of Pinon Device under the programming side: 6.
  • Connector type on Device under the programming side: Female.
  • Header Pin Pitch: 2.54mm (0.1in).

AVR-ISP 10Pin to 6pin Adapter PCB for USBASP Programmer

470.00 inc. GST
  • Made of high-quality material, practical and durable
  • Number of Pinon USBASP side: 10.
  • A number of Pinon Device under the programming side: 6.
  • Connector type on USBASP side: Male.
  • Connector type on Device under programming side: Female.
  • Header Pin Pitch: 2.54mm (0.1in).

CH341A 24 25 Series EEPROM Flash BIOS USB Programmer with Software & Driver

600.00 inc. GST
  • USB interface
  • With CH341A chip
  • Support 24 EEPROM and 25 SPI flash 8pin or 16pin chip
  • With 24/25 status indicator lamp
  • Support USB to TTL conversion
  • Support 24EEPROM and 25 SPI flash 8pin/ 16pin chip
  • Recognize 25 series chip automatically
  • Supports download STC series procedure of single chip
  • SPI pin to support expanding the utility
  • STC microcontroller supports a full range of program download
  • Support expanding the utility by SPI pin
  • With SOP8 SOP16 to DIP8 converter board
  • Used in wide applications – PC motherboard, LCD monitor, DVD, router program reading and writing
  • Supports Windows XP, Vista, Win7 and Win8 (32/64bit) system
  • Provide 5V-3.3V power supply output

CH375B U-DISK Read Write Module USB interface communication SPI interface

650.00 inc. GST
  • Power Supply: 5 V
  • Material: Acrylic
  • Colour: Blue
  • Compatible With: Arduino Board
  • Onboard Voltage: 3.3 V
  • Current Rating: 800 mA
  • 12 MHZ crystal.
  • USB status indicator.
  • PCB Size: 48 mm x 27 mm

MAX3232 RS232 TO TTL CONVERTER

130.00 inc. GST
  • Chip model: MAX3232 IC
  • Supply voltage: 3V -5V
  • Maximum Baud Rate: up to 120kbps
  • High speed, replaceable MAX232 based.
  • Working mode: Full duplex
  • Supports microcontroller UARTs – 5V TTL signal levels.
  • Low current status LED(s)
  • Very low power consumption
  • Optional onboard PSU for internal/external use for a quick start out of the box.
  • Power can be routed to pin 9 (if required) on the RS232 connector – useful for specific
  • Operating temperature: -40 degree to +85 degree Celsius
  • Dimension: 16.22*10.3*3.5mm
  • Weight: 1gm
 

Mini St-Link V2 Stlink Emulator Downloader Stm8 Stm32 with Metal Shell

950.00 inc. GST
  • Support the full range of STM32 SWD interface debugging, simple interface (including power supply), 4 line speed, stable work; Interface definition shell directly address
  • Support all series STM8 SWIM download debugging (common development environment such as IAR, STVD, etc.) are supported.
  • Support the firmware upgrade automatically, to ensure that the ST company product support. When they leave the firmware has been upgraded to the latest V2. The J17. S4.
  • Increase the 5 v power output, the output it can protect the I/O port, not afraid of error cause damage of ST-LINK V2.
  • Easy interface to use pure copper plating 2.54 spacing horn, with 20 cm Dupont line, can deal with different target board line sequence, flexible connection;
  • Use U disk aluminium alloy shell to protect the mainboard, convenient to carry, not afraid of static electricity, not afraid of tumbling.
  • Material: metal + plastic
  • Colour: Black/Red/Green/Pink/Gold/Grey/Blue/White( Randomly Sent )
  • Power output: 5V
  • simulator: about 5.6*2*0.8cm
  • Debugging line: about 20cm
  • Weight (kg): 0.012

Pic Kit-2 Programmer

2,200.00 inc. GST
  • Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
  • Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
  • Includes the UART Tool and Logic Tool microcontroller development utilities.
  • With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
  • High-quality PCB FR4 Grade with FPT Certified

PICkit 3.5 Compatible Programmer with USB Cable and Jumper Wire- PIC Kit

1,900.00 inc. GST
  • Type: Debugger/Programmer
  • Tool/Board Application: Debugging/Programming
  • MCU Supported Families: Flash-based PIC MCUs
  • Core Architecture: PIC, dsPIC
  • IC Product Type: In-Circuit Debugger
  • USB (Full speed 12 Mbits/s interface to host PC)
  • Real-time execution
  • MPLAB IDE compatible
  • Built-in over-voltage/short circuit monitor
  • Firmware upgradeable from PC/web download
  • Supports low voltage to 2.0 volts (2.0v to 6.0v range)
  • Diagnostic LEDs (power, busy, error)
  • Read/write program and data memory of the microcontroller
  • Erase of program memory space with verification
  • Freeze-peripherals at breakpoint
  • Program up to 512K byte flash with the Programmer-to-Go
  • Easy to use Windows-based programming
  • USB Interface
 

PICKIT-3 Programmer

2,200.00 inc. GST
  • Full-speed USB support using Windows standard drivers
  • Real-time execution
  • Processors run at maximum speeds
  • Built-in over-voltage/short circuit monitor
  • Low voltage to 5V (1.8 to the 5V range)
  • Read/write program and data memory of the microcontroller
  • Diagnostic LEDs (power, active, status)
  • Read/write program and data memory of the microcontroller
  • 1Erase of all memory types (EEPROM, ID, configuration, and program) with verification
  • Peripheral freeze at the breakpoint.
  • Program up to 512K byte flash.

PICKIT2 Microcontroller USB Programmer PIC KIT2 Burner

1,750.00 inc. GST
  • Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
  • Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
  • Includes the UART Tool and Logic Tool microcontroller development utilities.
  • With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
  • High-quality PCB FR4 Grade with FPT Certified

PL2303 USB TO TTL CONVERTER

250.00 inc. GST
  • USB specification 2.0 compliant with full-speed 12Mbps.
  • Operation Level-Digital 5V
  • Power Supply-External 5V
  • Standard USB type A male and TTL 6pin connector.
  • 6 pins for 3.3V, RST, TXD, RXD, GND & 5V.
  • All handshaking and modem interface signals.
  • Baud rates: 300 bps to 1.5 Mbps.
  • Byte receives buffer; 640 bytes transmit buffer.
  • Hardware or X-On/X-Off handshaking supported.
  • Event character support Line break transmission.
  • USB suspend states supported via SUSPEND pins.
  • Supports Windows 98SE, 2000, XP, Vista, Window7, Mac OS 9, Mac OS X & Linux 2.40.
  • Simple serial communication.
  • Router or ADSL firmware upgrade.
  • Easy to use, RX to the MCU's TX; TX to the MCU's RX. and then connected to the GND. Without having to use the MAX232 conversion.

RS232 TO RS485 CONVERTER ADAPTER

550.00 inc. GST
  • Input: USB 2.0 Protocol
  • Output: RS232 on DB9 Male connector compatible to PC RS485/RS422 on the terminal block.
  • Communication Speed: 300bps to 230Kbps.
  • Auto direction control for RS485- 2W data transmission.
  • Plug-and-Play (Device is Hot-pluggable)
  • Cable: USB 2.0 type A to type B cable.
  • Galvanic Isolation of 1.5kV
  • RS232/RS485 line protection: +/- 15kV ESD.
  • LED Indication for Transmit Receive signals.
  • Input power from the USB port
  • No external power is required.
  • RS232 with DB9 Female connector
  • RS485 with DB9 Male connector
  • Baud rate up to 230Kbps.
  • Input power supply range 9-6V DC to 26.4V DC
  • USB Drivers provided for Win XP, Vista, Win7, Win8
  • Working Modes: Asynchronous, half-duplex, differential transmission
  • Operating temperature: -10°C to 85°C,
  • Relative humidity: 5% to 95%
  • Transmission distance: 1.2 mile (RS-485), 5 meters(RS-232)
  • Transmission Media: Common wire, double wire, UTP or Shielding Line
  • Serial Port Feature: Compatible with EIA/TIA RS-232C standard and RS-485 standard
  • Weight: 49gm