I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Pic Kit-2 Programmer
₹2,400.00 Original price was: ₹2,400.00.₹2,200.00Current price is: ₹2,200.00. inc. GST
- Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
- Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
- Includes the UART Tool and Logic Tool microcontroller development utilities.
- With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
- High-quality PCB FR4 Grade with FPT Certified
The PICkit 2 Development Programmer/Debugger was designed as a low-cost development tool with an easy-to-use interface for programming and debugging Microchip’s Flash families of microcontrollers. This programmer is capable of programming all current 8-, 16-, and 32-bit Flash PIC microcontrollers. And also includes the UART Tool and Logic Tool microcontroller development utilities.
Microchip’s PICKit2 is designed as much more comfortable, reliable, and powerful than the other programmers all over the internet. It is a USB-based ICSP (In-Circuit Serial Programming) programmer. As PICKit2 is a USB-powered device, it gets power from a PC USB +5V power supply. Meanwhile, the soul of the PICKit2 is the USB microcontroller PIC18F2550. The USB Data+ and Data- from the PC connected to the D+ and D- pins of the PIC182550. Moreover, using a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller. It is made up of high-quality PCB FR4 Grade with FPT Certified. This programmer module supports the following device families:
- PIC10F
- PIC12F
- PIC16F
- PIC18F
- PIC24

Related products
1 CHANNEL 5V RELAY
- 1 channel relay board
- Operating voltage: 5V
- Maximum current: 2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- configured as SINGLE POLE DOUBLE THROW( SPDT)
- LED status indicates relay ON/OFF state.
- Standard TTL level logic controlled
- One normally closed and one normally opened contact
- Compatible with any 5V microcontroller
- Dimension: 43*17*17mm
- Weight: 150gm
16 CHANNEL 12V RELAY
- 16 channel 12V relay board
- Operating voltage: 12V
- Supply current: 0.2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- LED status indicates relay ON/OFF state.
- The 10-16 road can be any full-on/off or any road
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Normally closed or normally open with each port
- Strong anti-jamming ability and stable performance
- The on-board power supply module doesn’t need any external power
- Dimension: 180*90*20mm
- Weight: 100gm
3.3V/5V MB102 Breadboard Power Supply Module
- Input voltage: 6.5V to 12V
- Output voltage: 3.3V to 5V
- Output current: 700Ma
- Apply to MB102 breadboard
- Sorting jumpers used to switch voltage between 3.3V and 5V
- Onboard LED indicator to show the presence of power
- Short circuit protection
- Fits securely on standard 400 and 830 points on the breadboard
- Dimensions: 53*32*23mm
- Weight: 10gm
4 CHANNEL 12V RELAY
- 4-Channel relay interface board
- Relay input voltage: 12V DC
- Relay output: 5A/250V AC
- Signal input:5V DC from the microcontroller
- High current relay of 10A @250 V AC/10A@ 30V DC
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances such as DC motors, solenoid valves, lamps, etc.
- LED status indicates relay ON/OFF state.
- Power battery terminal for relay output and aux power connection
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- Relay can directly control all equipment’s and loads
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 165*65*1mm
- Weight: 7gm
89C2051 Atmel Microcontroller IC
- Core Processor: 8051
- Data Bus Width: 8 bit
- Maximum Clock Frequency: 24 MHz
- Program Memory Size: 2 KB
- Program Memory Type: Flash
- Supply Voltage Range: 4 V to 6 V
- Package: PDIP-20
- Compatible with MCS-51â„¢ Products
- 2K Bytes of Reprogrammable Flash Memory – Endurance: 1,000 Write/Erase Cycles
- 7V to 6V Operating Range
- Fully Static Operation: 0 Hz to 24 MHz
- Two-level Program Memory Lock
- 128 x 8-bit Internal RAM
- 15 Programmable I/O Lines
- Two 16-bit Timer/Counters
- Six Interrupt Sources
- Programmable Serial UART Channel
- Direct LED Drive Outputs
- On-chip Analog Comparator
- Low-power Idle and Power-down Modes
PICKIT2 Microcontroller USB Programmer PIC KIT2 Burner
- Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
- Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
- Includes the UART Tool and Logic Tool microcontroller development utilities.
- With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
- High-quality PCB FR4 Grade with FPT Certified
PL2303 USB TO TTL CONVERTER
- USB specification 2.0 compliant with full-speed 12Mbps.
- Operation Level-Digital 5V
- Power Supply-External 5V
- Standard USB type A male and TTL 6pin connector.
- 6 pins for 3.3V, RST, TXD, RXD, GND & 5V.
- All handshaking and modem interface signals.
- Baud rates: 300 bps to 1.5 Mbps.
- Byte receives buffer; 640 bytes transmit buffer.
- Hardware or X-On/X-Off handshaking supported.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Supports Windows 98SE, 2000, XP, Vista, Window7, Mac OS 9, Mac OS X & Linux 2.40.
- Simple serial communication.
- Router or ADSL firmware upgrade.
- Easy to use, RX to the MCU's TX; TX to the MCU's RX. and then connected to the GND. Without having to use the MAX232 conversion.
USB Blaster ALTERA CPLD/FPGA Programmer
- Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data.
- Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000, and MAXII.
- FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K, and FLEX10K, etc.
- Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc.
- Enhanced configuration devices: EPC1, EPC4.
- Supports 3 download modes: AS, PS, and JTAG.
- Support and Nios II embedded soft core processor communication and debugging Rev.C latest version Hardware. Support jtag_uart.
- Speed is 6 times faster than parallel port download cable ByteBlasterII.
- Easy to use: MiniUSB interface, easy connection, two status indicator makes debugging more comfortable.
- Fully compatible with ALTERA USB Blaster, functionality and performance are the same as ALTERA original download cable.
- Operating Voltage: 1.5~5V JTAG IO Voltage.
- System configuration: Windows XP, Windows Vista, Windows7, USB interface.

Reviews
There are no reviews yet.