Showing 1–12 of 29 results

Show sidebar

1602 LCD Shield

350.00 275.00
  • Operating Voltage:5V
  • 5 Push buttons.
  • RST button to reset Arduino program.
  • Integrate a potentiometer for adjusting the backlight.
  • Expanded available I/O pins.
  • Blue light with white characters.
  • Uses 4 Bit Arduino LCD Library
  • Screen contrast adjustment
  • Arduino Reset button
  • The keypad consists of 6 keys select, up, right, down, left and reset.
  • To save the digital IO pins, the keypad interface only uses one ADC channel.
  • The key value is read out through a 5 stage voltage divider.

2.4″ Inch Touch Screen TFT Display Shield for Arduino

850.00 699.00
  • 4″ Touch LCD TFT display module for Arduino
  • 240*320 pixels resolution
  • Ability to display 262000 different colors
  • Shield comes equipped with a microSD card slot.
  • SPFD5408 controller with built-in video RAM buffer
  • 8-bit digital interface, plus 4 control lines
  • 5V compatible. Use with 3.3V or 5V logic
  • On-board 3.3V 300mA LDO regulator
  • Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3, and analog 4 and 5. Pin 12 is available if not using the microSD
  • Works with any Arduino Uno and mega compatible boards
  • Resolution: 240320 pixels
  • Supply voltage: 5V
  • Working temperature: -30C ~ 70C
  • Dimension: 72*52*12mm

Arduino CNC Shield v3 Engraving Machine/3D Printer/A4988 driver GRBL compatible

500.00 199.00
  • Coolant enable
  • Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825, and others) (Not Included)
  • Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
  • Compact design.
  • Stepper Motors can be connected with 4 pin Molex connectors or soldered in place.
  • Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
  • Please note that this is an unassembled kit and needs soldering.
  • Latest Arduino CNC Shield Version 3.10
  • GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
  • PWM Spindle and direction pins
  • 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
  • 2 x End stops for each axis (6 in total)

Arduino Compatible Nokia 5110 Prototype Proto Shield Expansion Board

546.22 504.20
  • Supports Nokia5110 display
  • Standard 0.1"x0.1" prototyping grid with big pads
  • Comes with Stacking headers and plain header, choose whichever you want when soldering together
  •  IC pattern for adding DIP ICs up to 20 pins
  • Power rails down the middle and sides
  • Reset button and an extra general use button
  • 2 3mm general use LEDs, red and green, as well as 2 matching resistors
  • A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
  • Surface-mount chip area for up to 14 SOIC size parts
  • Compatible with tiny breadboards
  • Every pin is brought out
  • Gold plated pads
  • 2 x 0.1uF capacitors on either side for extra power stability

Arduino Duemilanove & USB Cable

900.00 850.00
  • Microcontroller: ATmega168/ATmega 328
  • Operating Voltage: 5V
  • Input Voltage: 7-12V
  • Input Voltage: 6-20V
  • Digital I/O Pins: 14 (of which 6 provide PWM output)
  • Analog Input Pins: 6
  • DC Current per I/O Pin: 40 mA
  • DC Current for 3.3V Pin: 50 mA
  • Flash Memory: 16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB used by bootloader
  • SRAM: 1 KB (ATmega168) or 2 KB (ATmega328)
  • EEPROM: 512 bytes (ATmega168) or 1 KB (ATmega328)
  • Clock Speed: 16 MHz

Arduino Leonardo R3

  • Board Mode: LEONARDO R3
  • Microcontroller: ATmega32u4
  • Operating Voltage: 5V
  • Input Voltage (Recommended): 7-12V
  • Input Voltage (limits): 6-20V
  • Digital I/O Pins: 20
  • PWM Channels: 7
  • Analog Input Channels: 12
  • DC Current per I/O Pin: 40 mA
  • DC Current for 3.3V Pin: 50 mA
  • Flash Memory: 32 KB
  • SRAM: 2.5 KB (ATmega32u4)
  • EEPROM: 1 KB (ATmega32u4)
  • Clock Speed: 16 MHz

Arduino Mega 2560 Board

1,200.00 799.00
  • Microcontroller: ATmega2560
  • Operating Voltage: 5V
  • Input Voltage (recommended): 7-12V
  • Input Voltage (limits): 6-20V
  • Digital I/O Pins: 54 (of which 15 provide PWM output)
  • Analog Input Pins: 16
  • DC Current per I/O Pin: 40 mA
  • DC Current for 3.3V Pin: 50 mA
  • Flash Memory: 128 KB of which 4 KB used by boot loader
  • SRAM: 8 KB
  • EEPROM: 4 KB
  • Clock Speed: 16 MHz

Arduino Nano V3.0

300.00 200.00
  • Microcontroller: Atmel ATmega328 SMD Package
  • Operating Voltage (logic level): 5 V
  • Input Voltage (recommended): 7-12 V
  • Input Voltage (limits): 6-20 V
  • Digital I/O Pins: 14 (of which 6 provide PWM output)
  • Analog Input Pins: 8
  • DC Current per I/O Pin: 40 mA
  • Flash Memory: 32 KB (of which 2KB used by bootloader)
  • SRAM: 2 KB
  • EEPROM: 1 KB
  • Clock Speed: 16 MHz
  • Automatic reset during program download
  • Power OK blue LED
  • Green (TX), red (RX) and orange (L) LED
  • Auto sensing/switching power input
  • Small mini-B USB for programming and serial monitor
  • ICSP header for direct program download
  • Standard 0.1” spacing DIP (breadboard friendly)
  • Manual reset switch
  • Dimensions: 0.70” x 1.70”

Arduino UNO R3 Clone

500.00 398.00
  • Microcontroller: ATMEGA328
  • Operating voltage: 5V
  • Input voltage: 7-12V
  • Digital I/O: 14 (6 provide PWM outputs)
  • Analog inputs: 6
  • Flash Memory: 32KB
  • SRAM: 2KB
  • EEPROM: 1KB
  • Clock Speed: 16MHz
  • DC Current per I/O Pin: 40 mA
  • DC Current for 3.3V Pin: 50 mA

ATtiny85 Arduino-enabled Mini USB Dev Board

250.00 200.00
  • Support for the Arduino IDE 1.0+ (OSX/Win/Linux)
  • Power via USB or External Source
  • Onboard 5V Regulator
  • Built-in USB
  • 6 I/O Pins
  • 8k Flash Memory (about 6k after bootloader)
  • I2C and SPI (vis USI)
  • PWM on 3 pins (more possible with Software PWM)
  • 10-bit ADC
  • ADC on 4 pins
  • Power LED and Test/Status LED
  • Low Power Consumption
  • Active Mode:1 MHz, 1.8V: 300 µA

Bluetooth Relay Shield

  • Supply Voltage: 5V
  • Max Relay current: 5 Amps
  • Potential free contacts
  • Bluetooth Wireless Interface
  • 200 to 300 Ft. Wireless Range
  • Mounts as a Virtual COM Port on PC/Laptop
  • Pair with Smartphone or Tablet

CAN Bus Shield

  • Implements CAN V2.0B at up to 1 Mb/s
  • Industrial standard 9 pin sub-D connector
  • OBD-II and CAN standard pinout selectable.
  • Changeable chip select pin
  • Changeable CS pin for TF card slot
  • Changeable INT pin
  • Screw terminal that easily to connect CAN_H and CAN_L
  • Arduino Uno pin headers
  • Grove connectors (I2C and UART)
  • SPI Interface up to 10 MHz
  • Standard (11 bit) and extended (29 bit) data and remote frames
  • Two receive buffers with prioritized message storage