Showing 37–44 of 44 results

SD Card shield V4.0 for Arduino UNO

₹1,275.00 inc. GST
  • Standard SD card, SDHC card and TF card compatible
  • 3.3v and 5v logical voltage compatible
  • 2.6-3.6v DC power supply
  • UART Grove & I2C connection compatible
  • Fully supported SD Library
  • Minimal number of SPI port
  • Jumpers provided for configuring Arduino SPI port pins
  • Onboard toggle switch for SD card select type
  • Truly stackable
  • Prototype expand Library support
  • Size: 53mm x 47mm
  • Weight: 35g

Sensor Shield V5 Expansion Board For Arduino

₹300.00 inc. GST
  • Retain the merits of the V4.0 version
  • Laminated design
  • PCB immersion gold processing technology
  • IIC interface
  • Bluetooth module communication interface
  • SD card module communication interface
  • APC220 Wireless RF modules communication interface
  • RB URF v1.1 ultrasonic sensors interface
  • 12864 LCD string of line and parallel interface
  • 32 servo controller interface

SIM800A Quadband GSM / GPRS Module convertible as Shield for Arduino

₹1,200.00 inc. GST
  • Quad-Band GSM/GPRS 850/ 900/ 1800/ 1900 MHz.
  • GPRS class 2/10.
  • Input Voltage: 9V-12V DC.
  • Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set).
  • Configurable baud rate.
  • Built-in SIM Cardholder.
  • Built-in Network Status LED.
  • 5V interface for direct communication with MCU kit.
  • Inbuilt Powerful TCP/IP protocol stack for internet data transfer over GPRS.
  • Low power.
  • SMA connector with GSM L Type Antenna.
  • Headphone jack for audio out.
  • Li-Po battery 3.7-volt pins for supply.
  • Li-Po battery USB charger (3.7volts).
  • CP2102 port for communication with a laptop.

UNO R3 +WiFi ATmega328P+ESP8266 Module CH340G Compatible For Arduino Uno

₹1,300.00 inc. GST
  • Microcontroller: ATmega328IC
  • Wi-Fi: ESP8266
  • USB-TTL converter: CH340G
  • Power Output: 5V-800mA
  • Power input USB: 5V (500mA max.)
  • Power input VIN/DC Jack: 9-24V
  • Power Consumption: 5V 800mA
  • Logic Level: 5V
  • WiFi: 802.11 b/g/n 2.4 GHz
  • USB type: Micro USB
  • USB Clock Frequency: 16MHz
  • Operating Supply Voltage: 5V
  • Digital I/O Pins: 14
  • Analog I/O pins: 6
  • Memory Size: 32Mb
  • Interface Type: serial
  • Operating temperature: −40С°/+125С°
  • Dimensions (L×W)mm: 53.34×68.58

UNO R3 Transparent Case

₹150.00 inc. GST
  • Material: A grade acrylic sheet.
  • For Arduino UNO R3 Development Board only.
  • With screw copper pillar and installation instructions.
  • To protect your little computer against damages, dust and scratches Clear Top and Bottom.
  • This case provides easy access to all ports.
  • It requires no tools for easy assembly and disassembly.
  • Simply Clicks Together Enclosure.

USB Host Shield

₹1,400.00 inc. GST
  • Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards.
  • Operates over the extended -40°C to +85°C temperature range
  • Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host)
  • Supports HID devices, such as keyboards, mice, joysticks, etc.
  • Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard drives (FAT32 Type File System – Mega Arduino only).

Wemos D1 WiFi Esp8266 Development Board Uno Compatible Program

₹775.00 inc. GST
  • Microcontroller: ESP-8266EX
  • Operating Voltage: 3.3 V
  • Digital I/O Pins: 11
  • Analog Input Pins 1(Max input: 3.2V)
  • Clock Speed: 80MHz/160MHz
  • Flash: 4M bytes
  • Good stability.
  • 11 digital input/output pins, all pins have interrupt/PWM/I2C/one-wire supported(except for D0)
  • 1 analog input(3.2V max input)
  • Micro USB connection
  • Compatible with Arduino
  • Support OTA wireless uploading
11 x I/O pins,1 x ADC pin~!
  • On-Board Switching Power Supply:
-Input Voltage Range: 9V to 12V -Output: 5V at 1A Max
  • Micro USB connection
  • Compatible with Arduino
  • Support OTA wireless uploading