• MPU-9150 GY-9150 9-Axis Electronic Compass Triaxial Accelerometer Gyroscope Module
- MPU-9150 module (three-axis gyroscope + tri axis accelerometer + axis magnetic field)
- Module Model: GY-9150
- Chip: MPU-9150
- Power supply :3-5v (internal low dropout regulator)
- Communication: IIC communication protocol standard
- 16bit AD converter-chip, 16-bit data output (field 13)
- Gyro Range: ± 250 500 1000 2000 ° / s
- Acceleration range: ± 2 ± 4 ± 8 ± 16g
- Magnetic field range: ± 1200uT
- Using Immersion Gold PCB, welding machines to ensure quality
- 54mm pin spacing
1 CHANNEL 12V RELAY
- 1-Channel relay interface board
- Operating voltage: 12V DC
- Provide high current relay of 15A
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances
- LED status indicates relay ON/OFF state.
- High current relay of 10A @250 V AC/10A@ 30V DC
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 43*17*17mm
- Weight: 150gm
1 CHANNEL 5V RELAY
- 1 channel relay board
- Operating voltage: 5V
- Maximum current: 2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- configured as SINGLE POLE DOUBLE THROW( SPDT)
- LED status indicates relay ON/OFF state.
- Standard TTL level logic controlled
- One normally closed and one normally opened contact
- Compatible with any 5V microcontroller
- Dimension: 43*17*17mm
- Weight: 150gm
1 x 5 Keypad Switch
1.44 red serial LCD display module 128*128 TFT Color Screen PCB Adapter
- Display Size: 1.44″
- Driver IC: ST7735
- Input Voltage: 3.3V to 5V
- Resolution:128×128 color pixels
- Touch Screen: NO
- Interface Type: SPI
- TFT color screen, the effect is far better than other small CSTN screen
- Fully compatible and alternative 5110 interface
- On-board LDO, support 5V/3.3V input voltage
- PCB Size: 44×30mm
10D OF 9-AXIS GY-87
- Power supply: DC 3.3V TO 5V
- 3 Axis Gyro+ Acceleration+ Magnetic field
- Air pressure module
- Inbuilt ultra-low noise linear LDO voltage regulator
- Inbuilt on board filters. which reduce noise from motor and another high current
- Communication: I2C protocol
- Power LED
- Designed for 5V logic
- Can easily select two I2C address for MPU6050 by soldered jumper
- Dimension: 2.2*1.7cm
- Size: 6gm
12V Wireless Power Supply Module Wireless Charging Module Wireless Transmission Module
- Magnetic-Coupled Resonance Technology
- Transmitting Voltage: 24V
- Output Power: 36W
- Output Voltage & Current: 12V, 3A
- Coil Size: outer diameter 82mm; inner diameter 30mm
- Transmitting Module Size: 17mm*30mm
- Receiving Module Size: 30mm*54mm
- Insulation Coil
- Compact Design
- Stable power supply
- Insulation Coil
- Space-saving design
16 CHANNEL 12V RELAY
- 16 channel 12V relay board
- Operating voltage: 12V
- Supply current: 0.2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- LED status indicates relay ON/OFF state.
- The 10-16 road can be any full-on/off or any road
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Normally closed or normally open with each port
- Strong anti-jamming ability and stable performance
- On-board power supply module doesn’t need any external power
- Dimension: 180*90*20mm
- Weight: 100gm
16 CHANNEL 5V RELAY
- 16 channel 5V relay board
- Operating voltage: 5V
- Supply current: 500mA
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- Low state voltage: 0V to 0.5V (relay is ON)
- High state voltage: 3.7V to 5V(relay is OFF)
- Single-chip design with reliable performance
- Strong anti-interferences
- Strong anti-jamming ability and stable performance
- On-board power supply module doesn’t need any external power
- Common terminal(com) in each rely is user friendly and ca be accessed by different signal
- Dimension: 180*90*20mm
- Weight: 100gm
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
- Adjustable frequency PWM up to about 1.6 kHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
- 3 pin connectors in groups of 4 so you can plug in 16 servos at once
- Chainable design
- A spot to place a big capacitor on the V+ line
- 220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial.
- This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers.
16×2 (1602) LCD Keypad Shield
- Operating Voltage:5V
- 5 Push buttons.
- RST button to reset Arduino program.
- Integrate a potentiometer for adjusting the backlight.
- Expanded available I/O pins.
- Blue light with white characters.
- Uses 4 Bit Arduino LCD Library
- Screen contrast adjustment
- Arduino Reset button
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
1×4 Key Matrix Switch Keypad
- Key Type: 4×1;
- Voltage: DC 12 Volt
- Mount Style: Self-Adherence
- Circuit Rating: 35 VDC, 100 mA.
- Contact Bounce : <=5ms
- Life Expectancy: 1 million closures
- Operation Temperature : -20 to +40 °C
- 5 pins 2.54mm pitch connector, 4×1 type 4 keys.
- Force : 250-350g
- Contact Bounce : Greater than 1s
- Cable Length : 52mm
- Ultra-thin design & adhesive backing provides easy integration to any project
- Excellent price-performance ratio
- Easy communication with any microcontroller
- Used widely in industrial and home electronic equipment's, instrument, etc.