UNO R3 Transparent Case

Original price was: ₹170.00.Current price is: ₹150.00. inc. GST
  • Material: A grade acrylic sheet.
  • For Arduino UNO R3 Development Board only.
  • With screw copper pillar and installation instructions.
  • To protect your little computer against damages, dust and scratches Clear Top and Bottom.
  • This case provides easy access to all ports.
  • It requires no tools for easy assembly and disassembly.
  • Simply Clicks Together Enclosure.

ATtiny85 Arduino-enabled Mini USB Dev Board

Original price was: ₹250.00.Current price is: ₹200.00.
  • Support for the Arduino IDE 1.0+ (OSX/Win/Linux)
  • Power via USB or External Source
  • Onboard 5V Regulator
  • Built-in USB
  • 6 I/O Pins
  • 8k Flash Memory (about 6k after bootloader)
  • I2C and SPI (vis USI)
  • PWM on 3 pins (more possible with Software PWM)
  • 10-bit ADC
  • ADC on 4 pins
  • Power LED and Test/Status LED
  • Low Power Consumption
  • Active Mode:1 MHz, 1.8V: 300 µA

L293D Motor Driver Shield

Original price was: ₹350.00.Current price is: ₹225.00. inc. GST
  • L293D motor driver chip & 74HC595 shift register
  • Four H-bridges
  • Terminal blocks and jumper to connect external power, for separate logic/motor supplies
  • Up to 4 bi-directional DC motors with individual 8-bit speed selection
  • Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
  • 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
  • 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC.
  • Pull-down resistors keep motors disabled during power-up
  • Big terminal block connectors to easily hook up wires (18-26AWG) and power
  • Arduino reset button brought up top
  • Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
  • PCB Size: 69 x 53 mm

NANO / UNO Multi-Purpose Expansion Board

Original price was: ₹250.00.Current price is: ₹225.00. inc. GST
  • The Sensor Shield makes your connections with the Arduino Nano much easier
  • It is compatible with Arduino Nano 2.0 and 3.0
  • The shield has up to 8 analogue pins, 13 digital I/O pins, and Aref with 3 pin connectors (GND, Vcc, Signal).
  • Consists of an independent I2C port with 4pins (SDA, SCL, GND, and Vcc) and UART (Rx, Tx, Vcc, and GND).
  • Reset button onboard and a female jack for external power supply
  • Material: FR-4 Epoxy Glass Fibre Board
  • IO port leads all digital and analogue IO ports, each IO port has positive and negative power supply interface standards.
  • Leads to an I2C interface on the motherboard, convenient and I2C devices connected.
  • Size: Approx. 57x53x8mm

Protosheild For Arduino

Original price was: ₹355.00.Current price is: ₹250.00. inc. GST
  • Standard 0.1"x0.1" prototyping grid with big pads
  • Comes with Stacking headers and plain header, choose whichever you want when soldering together
  • IC pattern for adding DIP ICs up to 20 pins
  • Power rails down the middle and sides
  • Reset button and an extra general use button
  • 2 3mm general use LEDs, red and green, as well as 2 matching resistors
  • A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
  • A surface-mount chip area for up to 14 SOIC size parts
  • Compatible with tiny breadboards
  • Every pin is brought out
  • Gold plated pads
  • 2 x 0.1uF capacitors on either side for extra power stability

Attiny 5 Version 1

Original price was: ₹300.00.Current price is: ₹250.00. inc. GST
  • High Performance, Low Power AVR® 8-Bit Microcontroller
  • Non-volatile Program and Data Memories
  • 8K Bytes of In-System Programmable Program Memory Flash
  • Endurance: 10,000 Write/Erase Cycles
  • 512 Bytes In-System Programmable EEPROM
  • Endurance: 100,000 Write/Erase Cycles
  • 512 Bytes Internal SRAM
  • Peripheral Features
  • High-Frequency PWM Outputs with Separate Output Compare Registers
  • USI – Universal Serial Interface (12C, SPI, 1-wire) with Start Condition Detector
  • 10-bit ADC
  • Single-Ended Channels
  • 2 Differential ADC Channel Pairs with Programmable Gain (1x, 20x)
  • Speed Grade: 0 – 10 MHz @ 2.7 – 5.5V, 0 – 20 MHz @ 4.5 – 5.5V
  • Low Power Consumption
  • Active Mode:1 MHz, 1.8V: 300 µA

Sensor Shield V5 Expansion Board For Arduino

Original price was: ₹450.00.Current price is: ₹300.00. inc. GST
  • Retain the merits of the V4.0 version
  • Laminated design
  • PCB immersion gold processing technology
  • IIC interface
  • Bluetooth module communication interface
  • SD card module communication interface
  • APC220 Wireless RF modules communication interface
  • RB URF v1.1 ultrasonic sensors interface
  • 12864 LCD string of line and parallel interface
  • 32 servo controller interface

Attiny 85

Original price was: ₹400.00.Current price is: ₹350.00. inc. GST
  • High Performance, Low Power AVR® 8-Bit Microcontroller
  • Non-volatile Program and Data Memories
  • 8K Bytes of In-System Programmable Program Memory Flash
  • Endurance: 10,000 Write/Erase Cycles
  • 512 Bytes In-System Programmable EEPROM
  • Endurance: 100,000 Write/Erase Cycles
  • 512 Bytes Internal SRAM
  • Peripheral Features
  • High-Frequency PWM Outputs with Separate Output Compare Registers
  • USI – Universal Serial Interface (12C, SPI, 1-wire) with Start Condition Detector
  • 10-bit ADC
  • Single-Ended Channels
  • 2 Differential ADC Channel Pairs with Programmable Gain (1x, 20x)
  • Speed Grade: 0 – 10 MHz @ 2.7 – 5.5V, 0 – 20 MHz @ 4.5 – 5.5V
  • Low Power Consumption
  • Active Mode:1 MHz, 1.8V: 300 µA

16×2 (1602) LCD Keypad Shield

Original price was: ₹450.00.Current price is: ₹400.00. inc. GST
  • Operating Voltage:5V
  • 5 Push buttons.
  • RST button to reset Arduino program.
  • Integrate a potentiometer for adjusting the backlight.
  • Expanded available I/O pins.
  • Blue light with white characters.
  • Uses 4 Bit Arduino LCD Library
  • Screen contrast adjustment
  • Arduino Reset button
  • The keypad consists of 6 keys select, up, right, down, left and reset.
  • To save the digital IO pins, the keypad interface only uses one ADC channel.
  • The key value is read out through a 5 stage voltage divider.

Arduino CNC Shield v3 Engraving Machine/3D Printer/A4988 driver GRBL compatible

Original price was: ₹500.00.Current price is: ₹400.00.
  • Coolant enable
  • Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825, and others) (Not Included)
  • Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
  • Compact design.
  • Stepper Motors can be connected with 4 pin Molex connectors or soldered in place.
  • Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
  • Please note that this is an unassembled kit and needs soldering.
  • Latest Arduino CNC Shield Version 3.10
  • GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
  • PWM Spindle and direction pins
  • 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
  • 2 x End stops for each axis (6 in total)

Joystick Shield

Original price was: ₹500.00.Current price is: ₹400.00. inc. GST
  • NRF24L01 RF interface.
  • For Nokia 5110 LCD interface.
  • Bluetooth interface I2C interface.
  • For one PS2 joystick.
  • 2-Axis joystick.
  • Bluetooth / Serial interface.
  • I2C interface.
  • nRF24L01 interface.
  • Nokia 5110 LCD interface.
  • Interface connector.
  • Power switch to switch between 3.3 and 5V