I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-10%
1Kg Load cell Electronic Weighing Scale Sensor
Original price was: ₹500.00.₹450.00Current price is: ₹450.00. inc. GST
LOAD CELL 10 Kg
Original price was: ₹500.00.₹450.00Current price is: ₹450.00. inc. GST
LOAD CELL 5Kg
Original price was: ₹500.00.₹450.00Current price is: ₹450.00. inc. GST
- Capacity: 5Kg
- Rated output(MV/V): 2.0±0.15
- Accuracy class: C2
- Maximum number of load cell verification intervals(N max): 2000
- Minimum number of load cell verification intervals(Vmin): E Max/5000
- Combined error(%RO): <±0.030
- Creep(%RO/30min): 0.03
- Temperature effect on sensitivity(%RO/°C): 0.0016
- Temperature effect on zero(%RO/°C): 0.003
- Zero balance(%RO): 1.0
- Input resistance(O): 402±6
- Output resistance(O): 350±3
- Insulation resistance(MO<50V>): 5000
- Recommended excitation voltage(V): 10~15
- Compensated temperature range(°C): -10~+40
- Operating temperature range(°C): -35~+80
- Safe overload(%RO): 150
- Ultimate overload(%RO): 200
- Load cell material: Aluminium
- Connecting cable: ø4.2*350mm
- Dimensions :3.45 x 2.4 x 0.9 inches
- weight:25gm
Description
A load cell transducer/sensor creates an electrical signal whose magnitude is directly proportional to the force measured. The various types of load cells include hydraulic load cells, pneumatic load cells, and strain gauge load cells. The standard straight bar load cell 5kg(sometimes called a strain gauge) translates up to 5 kg of pressure (force) into an electrical signal. Each load cell 5kg measures the electrical resistance that changes is proportional to the strain (e.g. pressure or force) applied to the bar. The output of the load cell is in milli-volts and cannot be directly measured by a micro-controller. So an ADC with high resolution or an instrumentation amplifier reads the output of the load cell to the microcontroller.
The intensity of deformity defines how much force applied, and this value digitally sent to an interface module. This gauge can determine how heavy an object is, whether the object’s weight changes over time or if you simply need to sense the object by measuring strain or load applied to a surface. This straight bar load cell made from an aluminum alloy. And it is capable of reading a capacity of 5KG of weight. These load cells also provide an IP66 protection rating for the sensor.
A load cell has four lead wires which connect HX711 A/D Pressure Sensor. It is easy to use with a driving voltage of 5-10V and produces the output voltage as the force changes.
Due to its high accuracy, it has a wide range of applications in the electronic platform scale, Digital scale, etc
Reviews (0)
Shipping & Delivery
Related products
10000W Original Chips Thyristor Super Power Electronic Regulator can Change Light Speed and Temperature
- Operating Voltage: AC 220 VDC
- Maximum Power: 10000W
- Voltage Range: AC 0-220V (adjust temperature or light)
- Controller Size: 95.7*56.7*53.8mm
- Panel Size: 74.6*59.8*2.3mm
- Cable Length: 287mm
- New two-way high-power SCR, max current up to 80A.
- Voltage regulator with the peak voltage absorption circuit effectively protects the high-power SCR and has a longer service life.
- Built-in heat sink, thickened to increase the heat sink, good heat dissipation, easy to install.
- 57A high current terminal block, simple wiring, strong button adjustment stability.
- Omron original tact switch, Fairchild original photoelectric coupler, all metal film resistors are stable and durable.
- The value is automatically saved. After power-on, it will automatically start to the last adjusted value.
- Weight: 200gm
6-30V 1-Channel Power Relay Module with Adjustable Timing Cycle
- Operating voltage: 6 - 30V DC
- 1 Channel delay trigerred relay module
- Delay time: 0.1 second ~ 999 minutes
- Seven Segment Display
- Operating voltage: DC 6V-30V (supports micro USB 5V power supply)
- Trigger signal source: high-level trigger (3V-24V) signal ground and system to improve the system's anti-jamming capability (also short-circuit altogether)
- Output capability: it can control the device within DC 30V 5A or within AC 220V 5A
- Quiescent current: 20mA
- Operating current: 50mA
- Service life: more than 100,000 times
- Working temperature: -40°C-85°C
- With optocoupler isolation, enhanced anti-jamming capability, industrial grade circuit board, set parameters for memory after power failure.
- Dimension: 6.2 * 3.8 * 1.7cm
MFRC522 RFID 13.56MHz
- Integrated MFRC522 module 13.56MHz RFID module
- Operating voltage: 2.5V to 3.3V
- Supports SPI, I2C protocol, UART communication
- Maximum data rate: 10Mbps
- Read range: 5cm
- Current consumption: 13-26 mA
- Power down mode consumption: 10mA
- Low cost and low voltage device
- Advanced modulation and demodulation concept completely integrated into all types of 13.56MHz passive contactless communication method and protocol
- 14443A compatible transponder signal
- Can be directly loaded into various reader molds
- Dimension: 12.3*11.9*3.8cm
- Weight: 20gm
RFID 13.56MHz Card
- Contactless transmission of data and supply energy (no battery needed)
- Operating distance: Up to 100mm (depending on antenna geometry)
- Operating frequency: 13.56MHz
- Data transfer: 106 kbit/s
- Data integrity: 16 Bit CRC, parity, bit coding bit counting
- Typical ticketing transaction: <100 ms ( including backup management)
- User-definable access conditions for each memory block
- Data retention of 10 years.
- Write endurance 100 000 cycles
- Reading and writing distance: 2.5-10CM
- Reading and writing time: 1-2MS
- Working temperature: -20 ° -85 °
- Packaging materials: PVC, PET, 0.13 coins
- Packaging technology: ultrasonic automatic line / automatic welding
- Production standards: ISO 14443, ISO 10536
RFID Key Fob 13.56mhz
- Operating frequency: 13.56 MHz
- Operating temperature: -45 °C to 85 °C
- Storage temperature: -55 °C to 100 °C
- Response Frequency: 13.56MHz
- Chip type: FM1108 Fudan Chip
- Memory capacity: 8 kbit
- Material: ABS
- Standard deployment: Attached to key fob and used for ID control
- For sensing and identifying tagged people and objects
- It is not re-programmable
- Dimension(LxWxH): 43.7×30.5×5.3mm
SP1848-27145 40x40mm Thermoelectric Power Generator TEG 150°C Peltier Module
- Model: SP1848-27145
- Open Circuit Voltage: 4.8 V
- Operating Temperature: 0 to 150 C
- Maximum Temperature: 150 Degree C
- Wire Length: 350mm
- 350Small and lightweight, convenient for use.
- Designed specifically for power generation.
- Sealed for moisture protection and contain thermal elements formulated for optimum Seebeck power generation.
- High-temperature 150C, with NM static protection.
- Quality tested cooling cells.
- Simple to install and operate.
- With 5v Booster board you can charge the cell phone
Reviews
There are no reviews yet.