I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-10%
SC10UU 10mm Linear Motion Bearing Slide Bushing Block
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
Black PLA 1.75 mm 1 Kg Filament For 3D Printer Wanhao
Original price was: ₹1,800.00.₹1,500.00Current price is: ₹1,500.00. inc. GST
100K ohm NTC 3950 Thermistor/Temperature Sensor for Reprap 3D printer Extruder
Original price was: ₹100.00.₹90.00Current price is: ₹90.00. inc. GST
- High-temperature Teflon wire temperature: 200 degrees
- Nominal resistance R25 (25 ℃): 100k
- Resistance accuracy: ± 1%
- B value R25 / 50: 3950k
- B value accuracy: ± 1%
- Operating temperature range: -40 ℃ ~ +300 ℃
- Dissipation power factor: ≥ 5 mW / ℃ (static air)
- Thermal time constant: ≤ 7S (static air)
- Maximum rated power: 45mW
- Wiring length: 1 meter
- Material: glass glaze film
Description
This 100K ohm NTC 3950 Thermistor/Temperature Sensor designed specifically for Reprap 3D printer Extruder or Heated Bed. This thermistor Conviniently pre-wired with 1 meter long high-temperature PTFE insulated wiring. Moreover, this offers a wide range of applications in 3d printing and often used with a heated bed or extruder. The Stainless steel tube encapsulation protects the probe from waterproof moistureproof thus prevents rust. This compact-sized, easy to install temperature sensor fairly precise ±0.5°C over much of the range.
Hence the temperature can be measured with a precision of 0.0625 C. It can give output is digitally accurate to 12 bits of precision from the onboard digital-to-analog converter. Here the NTC thermistor made up of think material with the heating rod made up of high-quality material. This temperature sensor module offers high sensitivity, and has a swift response, 1 percent, with a resistance value at 25°c= 100k. It uses adaptive thermosensitive material with high-quality wiring insulation with high temperature  Teflon/ PTFE
Reviews (0)
Shipping & Delivery
Related products
DHT22 MODULE
- Power supply: 3.3-5.5VDC
- Operating range: humidity 0-100%R
- Ultra-Low Power.
- No Additional Components.
- Long-Distance Signal Transmission.
- All Calibration, Digital Output & Completely Interchangeable.
- Relative Humidity & Temperature Measurement.
- Humidity Measurement Precision: 2-5% RH.
- Temperature Measurement Precision: 0.5 deg C.
- Calibrated digital signal
- Outstanding long-term stability
DS1820 Temperature Sensor
- Unique 1–Wire interface requires only one port pin for communication
- Multidrop capability simplifies distributed temperature sensing applications
- Requires no external components
- Can be powered from the data line
- Zero standby power required
- Measures temperatures from –55° C to +125° C in 0.5° C increments.
- Temperature is read as a 9–bit digital value.
- Converts temperature to digital word in 200 ms (Typ.)
- User-definable, nonvolatile temperature alarm settings
- Alarm search command identifies and addresses devices whose temperature is outside of programmed limits (temperature alarm condition)
HR202 Digital Temperature Humidity Sensor
- Working Voltage: 3.3 V-5 V
- Output AO - analog output, DO - digital output
- High-quality HR202 humidity sensor
- Comparator output signal is clean, good waveform, driving ability, more than 15mA
- Adjust the temperature distribution position detection threshold
- The output form: DO digital switching outputs ( 0 and 1 ) and AO analog voltage output
- A fixed bolt holes for easy installation
- Using a wide voltage LM393 comparator
- PCB Board Size: 3.2 cm x 1.4 cm
Stepper Motor Nema 23 kg 7.2 kg Dual shaft
- Rated Voltage: 6.6 V
- Current/ phase: 1A
- Resistance/ phase: 6.6ohms
- Inductance/ phase: 8.2 mH
- Holding Torque: 7.2 kg-cm
- of Leads - 6
- Rotor Inertia - 275
- Weight: 0.65kg
- Detent Torque: 0.36 kg-cm
- Step Angle - 1.8°
- Step Angle Accuracy - ±5% (full step, no load)
- Resistance Accuracy - ±10%
- Inductance Accuracy - ±20%
- Frame Size (mm) - 57x57
- Shaft Length (mm) - 20.6
- Shaft Diameter (mm) - 6.35
- Comparably more powerful than NEMA17 motors.
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
XH-W3001 DC 12V 120W Digital Microcomputer Thermostat Switch
- Rated Current: 10 Amp Max.
- Measurement Input: NTC10K
- Temp Probe Cable Length: 1 Meter
- Power Supply: DC12V
- Load Power: 120W
- Easy to install
- Output type: Direct output
- Output capacity: max 10A
- Temperature setting upper and lower limits
- Temperature measuring range: -50~110°C
- Temperature control range: -50~110°C
- Control precision: up to 0.1°C
- Up key: Press once to display the start temperature. Long press to set start temperature.
- Down key: Press once to display the stop temperature. Long press to set stop temperature.
- Temperature setting upper and lower limits
- Simple operation, suitable for seafood machines.
- Dimensions 60 x 45 x 31 (mm)
- Weight: 55gm
Reviews
There are no reviews yet.