I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-45%Sold out
MIP2E5DMY Power Device IC
Original price was: ₹100.00.₹90.00Current price is: ₹90.00. inc. GST
LM3915 Dot or Bar Display Driver IC
Original price was: ₹60.00.₹50.00Current price is: ₹50.00. inc. GST
LM3886 68W Audio Power Amplifier IC
Original price was: ₹2,200.00.₹1,200.00Current price is: ₹1,200.00. inc. GST
- High-Performance 68W Audio Power Amplifier with Mute
- 68W cont. avg. output power into 4Ω at VCC = ±28V
- 38W cont. avg. output power into 8Ω at VCC = ±28V
- 50W cont. avg. output power into 8Ω at VCC = ±35V
- 135W instantaneous peak output power capability
- Signal-to-Noise Ratio ≥ 92dB
- An input mute function
- Output protection from a short to ground or to the supplies via internal current limiting circuitry
- Output over-voltage protection against transients from inductive loads
- Wide supply range 20V – 94V
- 11-lead TO-220 package
Out of stock
Description
The LM3886 68W Audio Power Amplifier IC is a high-performance audio power amplifier with 23 channels. From 20Hz to 20kHz, this power amplifier delivers a constant average power of 68W to a 4 load and 38W to an 8 load with 0.1 percent THD+N. Meanwhile, using the LM3886’s Self Peak Instantaneous Temperature (°Ke) (SPiKe) protection circuitry increased the LM3886’s performance. As a consequence, by offering an intrinsically dynamically protected Safe Operating Area, this IC is classified as discrete and hybrid amplifiers (SOA). These parts are totally shielded/protected at the output against overvoltage, undervoltage, and overloads, according to the spike protection function. Shorts to supplies, thermal runaway, and instantaneous temperature peaks are all included.
The LM3886 offers an excellent signal-to-noise ratio of greater than 92dB with a typical low noise-floor of 2.0µV. It exhibits extremely low THD+N values of 0.03% at the rated output into the rated load over the audio spectrum. As a result, provides excellent linearity with an IMD (SMPTE) typical rating of 0.004%.The IC LM386 designed as one of the prominent integrated circuit used in the audio section. Also widely used for voice record from microphone, battery operated speakers. Moreover, this LM3886 Ic features Under-Voltage Protection, over voltage protection, spike protection and also thermal protection.
Moreover, the LM3886 IC provides a muting function that permits the user to mute the music going into the amplifier by drawing but 0.5 mA out of pin 8 of the device. The overvoltage protection circuitry in the IC limits the output current to approximately 11A peak. At the same time, it also provides voltage clamping, though not through internal clamping diodes.  The clamping effect is sort of an equivalent, however, the output transistors are designed to figure alternately by sinking large current spikes.
​​APPLICATIONS:
- Component stereo
- Compact stereo
- Self-powered speakers
- Surround-sound amplifiers
- High-end stereo TVs
Reviews (0)
Shipping & Delivery
Related products
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
Dean Connector
- Male plug size: About 13* 7* 19mm
- Female plug size: About 13* 7* 15mm
- Current Rating: 30Amps
- Colour: Red and golden
- Material: Plastic and metal
- Provides a secure connection for battery and motor connections
- Eliminates the possibility of wrong polarity connections
- Used in RC hobby, car, boat, plane, helicopter, LIPO battery, etc.
- Dimension: 9x0.7x2cm
- Weight:20gm
HX711–24 Bit Analog to Digital Converter (ADC)
- It is an ADC converter with two differential input channels
- An active-low noise PGA is integrated inside the chip which provides the gain of 32, 64 and 128
- It has a power-on-reset capability which simplifies digital interface initialization.
- All controls to the IC are made through the pins. Programming is not needed.
- You can select a data rate of 10SPS or 80SPS at the output.
- Provides simultaneous supply rejection of 50Hz and 60Hz supply.
- Built-in analog power supply regulator
- The voltage supply range is from 2.6V to 5.5V
- The temperature range is from -40 °C to +85℃
LM1876 Dual 20W Audio Power Amplifier IC
- Dual 20W Audio Power Amplifier with Mute and Standby Modes
- Spike Protection
- Minimal amount of external components necessary
- Quiet fade-in/out mute mode
- Standby-mode
- Isolated 15-lead TO-220 package
- THD+N at 1 kHz at 2 x 15W continuous average output power into 4Ω or 8Ω: 0.1% (max)
- THD+N at 1 kHz at continuous average output power of 2 x 20W into 8Ω: 0.009% (typ.)
- Standby current:Â 4.2 mA (typ.)
Solid State Relay Module DC To AC SSR-40DA 3-32VDC/24-380VAC 40A
- Control mode: DC-AC
- Input voltage: 3-32V DC.
- Output voltage: 24-380V AC.
- Output current: 40A.
- Working voltage: 250V.
- Material: plastic + metal.
- Loading current: 40A
- Control current: 3-25mA DC
- On voltage: ≤1.5V AC
- One-off Time: ≤10ms
- Off Leakage Current: ≤2mA
- Dielectrics voltage-resistance: 2500VAC
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
TDA7498 High Power Digital Amplifier Board 2*100W DC 14-34V Audio Stereo Amplifier Board
- High power class d digital amplifier.
- Two-channel stereo, 2x100w power output.
- Material: Metal
- 100 W + 100 W output power at THD = 10% with RL = 6 Ω and VCC = 36 V
- Wide-range single-supply operation (14 - 39 V)
- High efficiency (η = 90%)
- Four selectable, fixed gain settings of nominally 25.6 dB, 31.6 dB, 35.1 dB and 37.6 dB
- Applicable speaker impedance: 4/6/8 ohm(8 ohm is the best).
- Differential inputs minimize common-mode noise
- Standby and mute features
- Short-circuit protection
- Thermal overload protection
- Externally synchronizable
- size: 110*70*10mm
TDA7498E Double 160W Power Amplifier Dual Channel Stereo Audio Amplifier Module Support BTL Mode
- Amplifier chip: TDA7498E
- Working voltage: DC 15-36V (Recommend 32V, 8A, if power is too small will appear distortion and so on.)
- Output power: 2 x 160W
- Number of channels: Two-channel Stereo
- Efficiency: 85%
- Applicable speaker impedance: 4/6/8ohm (8ohm is the best).
- 160-W + 160-W output power at THD = 10% with RL = 4 Ω and VCC = 36 V
- 1 x 220 W output power mono parallel BTL at THD = 10% with RL = 3 Ω and VCC = 36 V
- Wide-range single-supply operation (14 - 36 V)
- High efficiency (η = 85%)
- Parallel BTL function using the MODE pin
- Four selectable, fixed gain settings of nominally 23.8 dB, 29.8 dB, 33.3 dB and 35.8 dB
- Differential inputs minimize common-mode noise
- Standby and mute features
- Smart protection
- Thermal overload protection
- Small offset less than 20 mV
- PCB board size: 108 x 78mm
- Weight: 172g(approx.)
Reviews
There are no reviews yet.