I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-8%
Solid Relay Module 4 channel 5v low level trigger for Arduino
Original price was: ₹800.00.₹775.00Current price is: ₹775.00. inc. GST
CH375B U-DISK Read Write Module USB interface communication SPI interface
Original price was: ₹750.00.₹650.00Current price is: ₹650.00. inc. GST
USB Charger Doctor
Original price was: ₹300.00.₹275.00Current price is: ₹275.00. inc. GST
- Display data: Voltage Current
- Operating Voltage: 3.5 to 7 V
- Maximum Current: 3 A ( accuracy of 0.4% )
- Battery Capacity (0-99999mah)
- Working time (0-99Hour)
- Charger voltage compliance DC 5V
- Resolution : Voltage 10mV current 1mA
- Error : voltage <± 1% current <± 2%
- USB Plug: 13mm / 0.5″
- RTZ, Reset button, press it three seconds will Reset
- The working time and Capacity have a Memory function when power is off.
- Compact and easy to carry, no additional power supply, plug, and play
- Detect any USB charger such as PC USB, home charger, car charger
- Easily measures the output voltage of the USB port and the device operating current or load voltage
- Dimensions: 21mm x 53mm x 15mm
- Weight: 16.2gm
Description
The USB Charger Doctor as its name indicates functions as a doctor. This doctor works when the voltage goes too low or the current rises too high. It measures the working voltage and current output for any USB port and project. This module is designed with blue plastic dongle plugs encapsulated between a USB device and passes the data lines through. A 0.05-ohm resistor arranged in line with the power pin measures the current draw. This USB charger doctor consists of an onboard digital display that instantly reads the values out for testing devices such as chargers, cables, and cell phones.
This device operates at a voltage ranging from 3.5v to 7VDC input voltage (although most USB devices tend to hover around 4.75 to 5.25). And can drive a maximum current up to 3A. It flips between voltage and current readouts every 3 seconds or so. This is a simple tool used commonly for testing USB devices, checking load levels, and debugging battery chargers and boost converters. Although it’s a little chunkier ensures a more precise value than our USB Power Gauge Mini-Kit. As this is not open-source, so check out the USB Power Gauge mini kit if you want to hack together your own power gauge indicator.
It offers a wide range of applications such as in any phone, any electronic products, factories, laboratories, etc. Finally, it reads out the voltage and current value from the USB port to help debug projects.
Reviews (0)
Shipping & Delivery
Related products
3 Wires 0.28 inch Digital Voltmeter DC 0-100V Red Light LED Panel Voltage Meter
- Display ON Voltage: 3 V
- Measurable Voltage Range: 0 to 100V
- Current Consumption: 10 mA
- Refresh Speed: 200ms (one time)
- Minimum Input: 3 V
- Highest Input: 30 V
- Accuracy: 0.1 V
- Colour: Red
- Wires: 3
- Operating Temperature: -10 to 60 degrees C
- Holes for Mounting: 3 mm
- Very small and lightweight voltmeter module.
- Very handy and easy to use.
- Red LED display.
- Best operates in the working voltage range of 5V to 24V
- Dimension: 13*30*9mm
- Weight: 3gm
3V To 5V 1A USB Charger Step Up Boost Module
- Module properties: Non-isolated step-up module (BOOST).
- Input voltage: 2.5-6V.
- Output voltage: 4-12 V (Adjustable (need to replacing the resistance to adjustable), the default 5 v).
- Output current: 1000mA (Max).
- Efficiency: 92% (Max) (the higher the input voltage, the higher the efficiency).
- Switching frequency: 1MHz.
- Output ripple: 20mV (MAX).
- Operating temperature: Industrial (-40°c to +85°c).
- Voltage regulation: ±2.5%.
- Short circuit protection: None
- Input: IN + postive, IN - negative.
- Output: USB output.
- Dimension: 3 x 1.3 x 0.8cm.
Dual USB 5V 1A 2.1A Mobile Power Bank Battery Charger
- Micro USB input: 5V 1A
- Charging voltage input: 5V-6V 1A.
- Step-up voltage output: 5V 1A/2.1A (Dual output, Total 2.5A).
- USB Output: 5V 2.1A / 5V 1A(Dual USB interface)
- Charging display: intelligent digital display
- Batteries Type: liquid lithium-ion batteries (18650)
- Best for Arduino, DIY Kits, Power bank, etc.
- Protection circuit: Overcharge protection: 4.250V Overcharge protection release: 4.100V.
- Protection circuit: Over-discharge protection: 2.900V Over-discharge protection release: 3.000V.
- Idle time before LCD switch off 60secs.
- Screen size:27mm x 17mm
- Dimension: 57mm x 28mm
Lipo Battery Charger B3
- Input voltage: AC 110V-240V, 50~60Hz
- Charge Current: 1.2A Max
- Cell Cut Off Voltage: 4.2V ± 0.02V
- Circuit Power: 11W ± 10%
- Balance charge current: 850mA
- Display: Green & Red LED
- Built-in power supply
- Case: Plastic
- Max charge power: 10W
- Only charge for 2~3 series LiPo battery
- Automatic charge start
- Simple, reliable, and safe to use
- Dimensions: 88x57x35mm
- Weight:103gm
LM2577 Boost power module
- Input voltage range : 3-34V DC
- Output voltage range : 4-35v DC adjustable
- Output current:3A
- Voltmeter range:0 to 40V,error +-0.1v
- Multiple output regulator.
- One button to switch input and output voltage display.
- Power-down memory function.
- Press the button for 3 seconds can turn OFF/ON the LED display.
- Multiple output regulator.
- When adjusting the blue potentiometer, please use a multimeter to monitor the voltage
- Rotating Clockwise can raise the voltage while rotating counter clockwise could lower the voltage
Reviews
There are no reviews yet.