I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Super Mini Elm327 V2.1 Bluetooth Obd2 OBD-Ii Car Auto Diagnostic Scanner Android
₹1,000.00 Original price was: ₹1,000.00.₹950.00Current price is: ₹950.00. inc. GST
- Model Name: ELM327 OBD2 Bluetooth
- Type: code readers & scan tools
- Output protocol: Bluetooth
- Material: plastic
- Voltage: 12V
- Current: 45mA
- Wave frequency: 38400Hz
- Applicable scope: 5-10m / 16.4-32.8ft
- Item size: 49*26*30mm
- Support OBDII Protocols: SAE J1850 PWM (41.6 kbaud), SAE J1850 VPW (10.4 kbaud), SAE J1939, J1979
ELM327 OBD2 V2.1 Bluetooth Interface Auto Car Diagnostic Scanner designed an on-Board Diagnostics. In an automotive context, OBD is a generic term that refers to a vehicle’s self-diagnostic and reporting capability. OBD systems provide the vehicle owner or a repair technician access to the state of health information for various vehicle sub-systems.
The amount of diagnostic information available via OBD has varied widely since the introduction within the early 1980s of onboard vehicle computers, which made OBD possible. Early instances of OBD would simply illuminate a malfunction indicator light, or MIL, if any error or issue was detected. But it does not provide any information on the character of the matter.
Modern OBD implementations make use of a uniform digital communications port to supply real-time data additionally to a uniform series of diagnostic trouble codes, or DTCs. As a result, permits one to rapidly identify and remedy malfunctions within the vehicle. ELM327 Bluetooth CAN-BUS scan tool supports OBD-II protocols. it’s wont to read & diagnose trouble codes, clear trouble codes and detect fuel pressure then on. The Elm327-Bluetooth adapter also gives you the chance to “spy” on your car wirelessly. By Converting PC, PDA, Mobile to a diagnostic tool and thus monitor all critical information of the car’s ECU.
The Elm327-Bluetooth is an adapter that connects to the car’s network then creates a virtual cable between the adapter and therefore the PC that it’s connected to. Moreover, with the assistance of varied open-source application for the Elm327, you’ll have a digital gauge or a complicated diagnostic system and a strong performance measurement toll in your screen.
- Engine RPM
- Calculated Load Value
- Coolant Temperature
- Fuel System Status
- Vehicle Speed
- Short Term Fuel Trim
- Long Term Fuel Trim
- Intake Manifold Pressure
- Timing Advance
- Intake Air Temperature
- Air Flow Rate
- Absolute Throttle Position
- Oxygen sensor voltages/associated short term fuel trims
- Fuel System status
- Fuel Pressure

Related products
4 CHANNEL 12V RELAY
- 4-Channel relay interface board
- Relay input voltage: 12V DC
- Relay output: 5A/250V AC
- Signal input:5V DC from the microcontroller
- High current relay of 10A @250 V AC/10A@ 30V DC
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances such as DC motors, solenoid valves, lamps, etc.
- LED status indicates relay ON/OFF state.
- Power battery terminal for relay output and aux power connection
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- Relay can directly control all equipment’s and loads
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 165*65*1mm
- Weight: 7gm
4*3 MATRIX KEYPAD
- Operating voltage: 12V DC
- The maximum voltage across each button: 24v
- The maximum current across each button: 3mA
- Ultra-thin design
- Adhesive backing provides easy integration
- Easy communication with any microcontroller
- Flexible
- Only 7 microcontroller pins required to access 12 keys
- High price-performance ratio
- Allows microcontroller to scan 8 output pins to check which 16 button
- Long life
- Maximum operating temperature: 0 degrees to 50 degrees Celsius
- Dimension: 70*77*1mm
- Weight: 7.5gm
8 CHANNEL 5V RELAY
- Relay operating voltage: 5V
- 8 channel
- High impedance controller pin
- One normally closed contact and one normally opened
- Useful for appliances control
- Power supply indicator and control indicator lamp
- Pull-down circuit to avoid malfunction
- Can control both DC and AC to 220v AC load
- Works with both 3.3 V and 5 V logic with the less current drive
- 3 terminals per SPDT relay
- Standard interface can be directly controlled by a microcontroller like Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic
- Dimension: 7*6.4*1 inch
DC POWER SUPPLY MODULE FOR DC ADAPTER PLATE
DIGITAL POWER AMPLIFIER BOARD MODULE 35W
IRF520 MOSFET DRIVER MODULE SENSOR
- Operating Voltage: 3.3v & 5v
- Digital level port
- Output load voltage: 0-24v
- Output load current: <5A
- The heat sink is added for currently more than 1A
- Compatible with Arduino, MCU, ARM, Raspberry pi
- PWM dimming LED used to step-less dimming, variable-speed motor
- Output PWM can be adjusted by the original IFR520 MOS
- Arduino can drive up to 24V, such as led lights, dc motors, miniature pumps, solenoid valves etc.
- Dimension:34*30*18mm
- Size: 10gm
ISD1760 MODULE (75 sec)
- On-board ISD1760 chip
- Operating voltage: 5v
- 75 sec of audio playback
- Onboard microphone for direct recording
- Frequency: 6KHz or 8KHz
- Recording time: 6K/75 sec, 8K/60 sec
- Output all pin for chip control
- Easy interface with microcontrollers using 2.54mm spaced male pin headers
- High-quality natural voice reduction
- LED status indication
- Long recording time and multiple messages
- Simple operation and better voice quality
- Control not only by buttons but also by SPI from a microcontroller
- Recording, erase, play, FT, fast forward, reset volume buttons
- Dimension: 49*41.5mm
- Weight: 22gm

Reviews
There are no reviews yet.