Relay Base Square 11 Pin
1000uf 250V Samwha DC Electrolytic Capacitor
12V 40W Ceramic Cartridge Heater 6mm*20mm For Extruder 3D Printers
- Material: stainless steel,
- Core: ceramic.
- Voltage: 12V.
- Power: 40W.
- Diameter: 6mm, Heating Length: 20 mm.
- Wire Length: 100 cm.
- Works on many 3D printers, including RepRap and Prusa models.
- It fits nicely in our extruder, so it’s an easy replacement.
- Small but powerful.
- Get your hotend hot quickly.
- This unit is a more powerful unit than the standard unit for many 3D printers.
28BYJ-48 5V Stepper motor
- High-quality stepper motor
- Voltage: DC 5V
- Diameter: 25mm
- Step Angle: 5.625 x 1/64
- Reduction Ratio: 1/64
- Rated voltage ： 5VDC
- Number of Phase ： 4
- Speed Variation Ratio ： 1/64
- Stride Angle ： 5.625° /64
- Frequency : 100Hz
- DC resistance ： 50Ω±7%(25℃)
- Idle In-traction Frequency : > 600Hz
- Idle Out-traction Frequency : > 1000Hz
- In-traction Torque >34.3mN.m(120Hz)
- Self-positioning Torque >34.3mN.m
- Friction torque : 600-1200 gf.cm
- Pull in torque : 300 gf.cm
- Insulated resistance >10MΩ(500V)
- Insulated electricity power ：600VAC/1mA/1s
- Insulation grade ：A
- Rise in Temperature <40K(120Hz
- Noise <35dB(120Hz,No load,10cm)
HC-SR505 Mini Infrared PIR Motion Sensor Infrared Detector Module
- Model: HC-SR505
- Operating Voltage Range: DC4.5-20V
- Average Current Consumption (mA): 0.06
- Distance Measuring Range: 3 meters
- Delay time: Default 8S + -30% (can be customized)
- Working Temperature Range: -20°C ~ 80°C
- Sensor Lens Diameter: 10mm
- Induction angle: <100-degree cone angle
- Low-power consumption
- Output level: High 3.3V / Low 0V
- Trigger: repeatable trigger (default)
- Automatic induction: to enter the sensing range of the output is high, people leave the sensor range automatically delay off high, output low
- Dimensions: 10 x 23 x 5mm
- Weight: 10gm
A4988 Stepper Motor
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Logic Voltage supply: 3.3 V to 5 V
- Compatible with 3V3 and 5V microcontrollers
- Our Board comes with 0.1 Ohm Sensor resistors
- Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
- The Correct current decay mode (fast decay or slow decay) is selected by chopping the control
- Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
- Short-to-ground and shorted-load protection
- 4-layer, 2 oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
16*2 GREEN (LCD DISPLAY MODULE)
- Input voltage: 4.7V TO 5.3V
- Operating voltage: 5V
- Current consumption: 1mA
- Input leakage current:1micro ampere
- HD44780 Equivalent LCD Controller/driver Built-In
- 4-bit or 8-bit MPU Interface
- Each character build by 5*8 pixels
- Consist of 2 rows with each row has 16 characters
- Operating temperature:0 degree to 50 degree Celsius
- Low Current consumption
- Green Backlight
- Works with almost any Microcontroller
- Alphanumeric display
- Compact size and lightweight
- Easy to interface
- Dimension: 69.5*14.5mm
