USB 2.0 Type A Male to USB A Male Cable
- USB 2.0
- Length:1m
- A-A male cable type
- Blue colored cable
- Standard USB 2.0 cable assembly, Type A male to type A male
- signaling rate: 480 Mbit/s (60 MB/s) Connector Type: USB 2.0 Type A Male to Type A Male
- High quality USB 2.0 high speed cable. Usually used for some external drive enclosures or cameras.
- Fully Compatible with USB 1.0,1.1 , Supports data transfer rate at up to 480Mbps
- Supports plug play connections for devices such as external hard drives, modems, printers, scanners, VOIP devices other USB peripherals.
- It is plug & play and hot swappable (no need to turn off your PC to plug a device in or out).
A-Male to A-Female USB 2.0 Extension Cable (150cm)
- Hi-Speed 480 mbps With 3g Dongle Support.
- Easy to operate, bring you great convenience.
- Made of high-quality Material
- USB 2.0 A Male to A Female Extension Cable.
- A-male to A-female USB cables are typically used to extend the reach of your existing USB A/B cable, or to use USB device such as memory stick on your desk instead of inserting it to the back of PC
- Left connector type: USB 2.0.
- Left connector gender: Male.
- Right connector type: USB 2.0.
- Right connector gender: Female
Serial RS-232 9 Pin Cable Male to Male
- Connector Type: DB9 Male to DB9 Male.
- Cable diameter: 6mm
- Cable length:1.5m
- Fully shielded to prevent unwanted EMI/RFI interference.
- Fully molded connectors with thumbscrews provide quick and easy connection.
- All lines wired straight through.
- Used for extending a 9 pin serial male to male cable, or connect it to an old serial port device along with a serial to USB converter
- Shielded with standard Foil-Al layer shielding as in most cables
Serial RS-232 9 Pin Cable Male to Female
- Connector Type: DB9 Male to DB9 Female.
- Cable diameter: 6mm
- Cable length:
- Fully shielded to prevent unwanted EMI/RFI interference.
- Fully molded connectors with thumbscrews provide quick and easy connection.
- All lines wired straight through.
- Used for extending a 9 pin serial male to male cable, or connect it to an old serial port device along with a serial to USB converter
- Shielded with standard Foil-Al layer shielding as in most cables
Ultrasonic Module HC-SR-04
- Sensor Type: Ultrasonic
- Output: Digital Sensor
- Voltage: 5VDC
- Operating Current: 15mA
- Measure Angle: 15°
- Ranging Distance: 2cm - 4m
- Static current: < 2mA
- Level output: high-5V
- Output Signal:5V
- High Precision: Up to 2 mm
- Input Trigger Signal: 10µs TTL impulse
- Echo Signal: Output TTL PWL Signal
- High sensitivity ultrasonic range sensor
- Works with Arduino board
5045(5×4.5) SF Propellers 2CW+2CCW-1pair
- Length: 5″.
- Pitch: 4.5″.
- Weight: 22 gm.
- Shaft diameter: 5mm.
- Total length: 5 inch / 125 mm.
- Material: Glass Fiber Nylon
- Durable plastic construction provides both lightness and rigidity.
- 5045(5X4.5) Glass Fiber Nylon Bullnose Black Propellers comes with an Epoxy resin cover.
- Very strong and lightweight.
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 26 gm.
7*9cm PERFBOARD
LM2596 3A STEP DOWN MODULE
- Module properties: non isolated constant voltage module
- Rectification : non synchronous rectification
- Input voltage: 4.5V-35V
- Output voltage: 1.3V-30V
- Output current: 3A maximum
- Conversion efficiency: 92%
- Switching frequency: 150KHz
- Output ripple: 50mV 20M bandwidth
- Load regulation: +/- 0.5%
- Voltage regulation:” +/-2.5%
- Operating temperature: -40 degree to 85 degree Celsius
- Dimension: 48*23*14mm
1 CHANNEL 5V RELAY
- 1 channel relay board
- Operating voltage: 5V
- Maximum current: 2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- configured as SINGLE POLE DOUBLE THROW( SPDT)
- LED status indicates relay ON/OFF state.
- Standard TTL level logic controlled
- One normally closed and one normally opened contact
- Compatible with any 5V microcontroller
- Dimension: 43*17*17mm
- Weight: 150gm
1 CHANNEL 12V RELAY
- 1-Channel relay interface board
- Operating voltage: 12V DC
- Provide high current relay of 15A
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances
- LED status indicates relay ON/OFF state.
- High current relay of 10A @250 V AC/10A@ 30V DC
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 43*17*17mm
- Weight: 150gm
LM318N Operational Amplifier IC
- Operational Amplifier
- Input Offset Voltage (max): 10mV
- Input Offset Current (max): 200nA
- Input Bias Current (max): 500nA
- Operating temperature (max): 700C
- Output Current (max): 8mA
- CMRR (min): 70dB
- 15 MHz Small Signal Bandwidth
- Ensured 50V/μs Slew Rate
- Maximum Bias Current of 250 nA
- Operates from Supplies of ±5V to ±20V
- Internal Frequency Compensation
- Input and Output Overload Protected
- Pin Compatible with General Purpose Op Amps
AMS1117 3.3V POWER SUPPLY MODULE
• Input: DC 4.5V – 12V (input voltage must be more than the output voltage (more than 1V))
• Output: 3.3V, 800mA (load current cannot exceed 800mA)
• Onboard AMS1117 chip.
• Onboard power indicator to indicate power is turned on: Red LED.
• Output voltage interface, connection to facilitate the experimental.
• Specially designed two pin mounting holes, can be directly fixed on the whole expansion board for experiments.
• Small Compact Size, 4Pin Type, Breadboard Friendly.
• 2P single row pin input and output for easy connection
• Dual-panel design, the layout is nice