R305 Optical Fingerprint Reader Sensor Module
- Power DC: 3.6V-6.0V
- Interface : UART (TTL logical level)/ USB 1.1)
- Working current: 100mA
- Peak Current: 150mA
- Matching mode (1: 1)
- Search method (1: N)
- Connecting cable length (cm): 8.5
- Baud rate (9600*N)bps, N=1-12 (default N=6 57600bps)
- Character file size: 256 bytes
- Image acquiring time: <0.5s
- Template size: 512 bytes
- Storage capacity: 256
- FAR : <0.001%; FRR: <0.1%
- Average searching time: < 0.8s (1:880)
- Working environment: Temp: -10degree to +40degree C
- Storage environment Temp: -40degree to +85degree C
- RH: 40%-85% RH: <85%
- Integrated image collecting and algorithm chip together, ALL-in-One.
- Low power consumption, low cost, small size, excellent performance.
- Professional optical technology, precise module manufacturing techniques.
- Good image processing capabilities can successfully capture an image up to a resolution of 500 dpi.
- Window dimension : 18mm*22mm
- Optical module: 49 x 20 x 21.20 mm
- Touch Sensors: 18 x 14.5 mm.
- Weight: 16gm
Sonar Range Finder -High Performance Ultrasonic Sensor Module
- Low-cost ultrasonic rangefinder
- Size less than 1 cubic inch with easy mounting
- Resolution of 1mm
- 100mS measurement cycle
- The free run operation uses a 2Hz filter, with 100mS measurement and output cycle
- Operating temperature range from -15°C to +65°C
- Operating voltage from 2.5V to 5.5V
- Nominal current draw of 2.5mA at 3.3V, and 3.1mA at 5V
Controller for 350W 36V Hub Motor – Electric Bike Bicycle
Ublox NEO 7M GPS With Compass for APM 2.6/2.8 and Pixhawk 2.4.6/2.4.8
- Tracking sensitivity: 161 dBm
- Capture sensitivity : 148 dBm
- Cold start time: 38s average
- Warm start time: 35s average
- Hot start time: 1s average
- Capture time: 0.1s Average
- Locate performance
- Pre-configured, Flashed with the correct settings and tested
- Super Bright LED
- Backplane with Standard Mk style mounting holes 45mm X 45mm
- 38400 bps (Default) Changed to 115200bps!
- Output GGA, GSA and RMC frames
- 1Hz (Default) Changed to 5Hz!
- Permanent Configuration Retention
- Onboard compass
- 6 pin connector for EZ connect to MEGA BLACK
- 4 pin connector for only GPS use
- 4 pin connector for compass only use
- Can use both 4 pin at once
pH Sensor Module & pH electrode Probe for Arduino, AVR, PIC
- Module Power: DC 5.00V.
- Measuring Range: 0-14PH.
- Accuracy: 0.01 pH
- Response Time: ≤ 1min.
- Industry pH Electrode with BNC Connector.
- Power Indicator LED.
- Output: Analog values in the range of (0.5V to 3V).
- Alkali Error: 0.2PH.
- Internal Resistance: 250MOhm.
- Gain adjustment Potentiometer.
- Measuring Temperature: 0 degrees to 50 degrees C
- Terminal Blocks: BNC plug.
- BNC Connector is suitable for most pH meters and controllers.
- Suitable for a wide range of applications: Aquariums, Hydroponics, Laboratory etc.
- Module Size: 50 x 47 x 16mm
Xbee Pro S2C Module XBP24CZ7WIT-004
- Operating voltage: 2.7V-3.6V
- Max data rate: 250kbps
- 63mW output (+17dBm)
- Range: 1 mile (1600m)
- ADC Channels: 6 10-bit ADC input pins
- Digital I/O: 8
- 128-bit encryption
- Transmit Current: 120mA at 3.3VDC
- Receive current: 31mA at 3.3VDC
- Data Rate: RF 250Kbps, serial up to 1Mbps
- Indoor/urban range up to 300ft (90m)
- outdoor/RF line of sight range up to 2miles (3200m)
- Transmit power is 63mW (+18dBm)
- Receiver sensitivity is -101dBm
- Local or over-air configuration
- AT or API command set
- External Antenna Required
- Firmware upgrades via UART, SPI or over the air (OTA)
- ISM 2.4GHz frequency band, DSSS (direct sequence spread spectrum) interference immunity
- Dimension: 2.438cm x 3.294cm
Raspberry Pi Camera Module V2 – 8 Megapixel 1080p
- 8-megapixel native resolution high-quality Sony IMX219 image sensor
- Cameras are capable of 3280 x 2464 pixel static images
- Fixed focus lens on-board
- Supports 1080p30, 720p60 and 640x480p90 video
- Connects to the Raspberry Pi board via a short ribbon cable (supplied)
- Uses the Sony IMX219PQ image sensor – high-speed video imaging and high sensitivity
- All software is supported within the latest version of the Raspbian Operating System
- Supports Raspberry Pi 1,2 and 3
- Dimensions: 25mm x 23mm x 9mm
- Weight: 3.4g
36V/48V/60V Lithium battery case 360*160*100MM APS Plastic Material
- Dimensions: 360*160*100mm.
- Suitable for battery type: 36/48/60V.
- Battery standard: 18650 lithium battery.
- Charging voltage: 42V/54.6V.
- Used to install an electric vehicle lithium battery.
- Suitable for electric bicycles, electric bicycles, and folding electric vehicles.
- Made up of plastic, which is sturdy and durable.
- The product has a charging socket and an output port.
36V/48V Fold bike Lithium Battery Case 410*100*42mm Aluminum Alloy Material
- Dimensions: 410*100*42mm.
- Suitable for battery type: 36/48V.
- Battery standard: 18650 lithium battery.
- Charging voltage: 42V/54.6V
- Used to install an electric vehicle lithium battery.
- Suitable for electric bicycles, electric bicycles, and folding electric vehicles.
- Made up of aluminium alloy and plastic, which is sturdy and durable.
- The product has a charging socket and an output port.
36V/48V Lithium Battery Case Aluminum Alloy Material 440*135*89
- Dimensions: 440*135*89
- Suitable for battery type: 36/48V.
- Battery standard: 18650 lithium battery.
- Charging voltage: 42V/54.6V.
- Used to install an electric vehicle lithium battery.
- Suitable for electric bicycles, electric bicycles, and folding electric vehicles.
- Made up of aluminium alloy and plastic, which is sturdy and durable.
- The product has a charging socket and an output port
36V/48V Lithium battery case aluminum alloy material 385*110*76
- Dimensions: 385*110*76mm.
- Suitable for battery type: 36/48V.
- Battery standard: 18650 lithium battery.
- Charging voltage: 42V/54.6V.
- Used to install an electric vehicle lithium battery.
- Suitable for electric bicycles, electric bicycles, and folding electric vehicles.
- Made up of aluminium alloy and plastic, which is sturdy and durable.
- The product has a charging socket and an output port.
24V Lithium Battery case 350*106*78mm
- Dimensions: 350*106*78mm.
- Suitable for battery type: 24V.
- Battery standard: 18650 lithium battery.
- Charging voltage: 24V.
- Used to install an electric vehicle lithium battery.
- Suitable for electric bicycles, electric bicycles and folding electric vehicles.
- Made up of aluminium alloy and plastic, which is sturdy and durable.
- The product has a charging socket and an output port.