Worm Gear Box Reduction Motor 12V 85rpm 6 kg-cm Torque – WGM370128500-100K
- Motor Type: DC Carbon Brush Motor.
- Gear Ratio:100: 1.
- Operating Voltage: 12.V DC
- Rated Current: 0.220A
- Rated Base Motor RPM: 8500.
- Rated Speed: 85RPM
- Rated Torque: 6kg-cm
- Operating Temperature: (°C) - -40 °C ～ +100°C.
- Relative Humidity(RH): 20% ～ 85% .
- Housing Material: Metal.
- Shaft Type: D-type.
- Motor Height: 25mm
- Motor Width: 32mm.
- Motor Length: 81mm
- Shaft Diameter: 6mm
- Shaft Length: 13mm
- Shaft Type: D-type. Motor
- Weight(gm): 170.
Worm Gear Box Reduction Motor 12V 10rpm 10 kg-cm Torque – WGM370128500-828K
250W 36V Electric Bike Bicycle Rear wheel Hub motor DIY Conversion Kit – Basic
TDA7498 High Power Digital Amplifier Board 2*100W DC 14-34V Audio Stereo Amplifier Board
- High power class d digital amplifier.
- Two-channel stereo, 2x100w power output.
- Material: Metal
- 100 W + 100 W output power at THD = 10% with RL = 6 Ω and VCC = 36 V
- Wide-range single-supply operation (14 - 39 V)
- High efficiency (η = 90%)
- Four selectable, fixed gain settings of nominally 25.6 dB, 31.6 dB, 35.1 dB and 37.6 dB
- Applicable speaker impedance: 4/6/8 ohm(8 ohm is the best).
- Differential inputs minimize common-mode noise
- Standby and mute features
- Short-circuit protection
- Thermal overload protection
- Externally synchronizable
- size: 110*70*10mm
Pedal Throttle for Electric Scooter/Bike/Tricycle Accelerator Foot Pedal – Type 2
Pedal Throttle for Electric Scooter/Bike/Tricycle Accelerator Foot Pedal – Type 1
250W 36V Electric Bike Bicycle Rear wheel Hub motor DIY Conversion Kit – Advanced
Creality Ender-3 V2 Upgraded 3D Printer with Silent Motherboard
- Moulding Technology: FDM(fused deposition manufacturing)
- Machine Size: 475*470*620mm
- Printing Size: 220*220*250mm
- Printer Weight: 7.8kg
- Hot end Temperature: ≤100℃
- Layer Thickness: 0.1-0.4mm
- Filament: PLA/TPU/PETG
- Support OS: MAC/WindowsXP/7/8/10
- Silver Software: Simplify3d/ Cura
- Printing Precision: ±0.1mm
- Filament Diameter: 1.75mm
- Rotary Knob added on the extruder
- Comes with Carborundum glass platform
- Self-developed silent motherboard
- Smart Injection Belt Tensioner
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
- Adjustable frequency PWM up to about 1.6 kHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
- 3 pin connectors in groups of 4 so you can plug in 16 servos at once
- Chainable design
- A spot to place a big capacitor on the V+ line
- 220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial.
- This board/chip uses an I2C 7-bit address between 0x60-0x80, selectable with jumpers.
Prototype Shield V3.0 For Arduino Mega with breadboard
- The shield can support being fully assembled with Arduino MEGA
- Support soldering components directly on this shield
- Support sticking the mini breadboards on this shield
- Reset button up top
- Mainboard aureate quadrate
- With SOP28 SMT components encapsulation
- With PWR & STAT indicator
- Breadboard Points : 170
- Shield Size (mm) : 102×56
- Breadboard Size (mm) : 48×34
- Weight (gm) :35
MQ-9 Carbon Monoxide, Methane and LPG Gas Sensor Module
- Input voltage: DC 5V
- Power: 150mA
- DO output: TTL digital 0 and 1 (0.1 and 5V)
- AO output: 0.1-0.3V (relatively clean), the highest concentration voltage is about 4V.
- Suitable for home or factory gas leakage monitoring devices.
- Have better sensitivity to Carbon Monoxide, Methane and LPG Gas.
- High quality dual-panel design, with power indicator and TTL signal output instructions.
- DO switching signal (TTL) output and AO analog signal output.
- TTL output valid signal is low. (When the output low signal is on, it can be directly connected micro-controller or relay module.)
- Analog output voltage: the higher concentration, the higher voltage.
- Four screw holes, easy positioning.
- Long life and stability, quick response and resume.
GPS Antenna Mount Folding Bracket Anodized Aluminum Carbon for M8N GPS MODULE APM PixHawk
- Material: CNC Aluminium alloy, carbon glass fiber rod
- Mounting rod diameter: 4mm
- Lead of rod: 14 cm. GPS plate diameter: 40 mm.
- Base plate diameter: 35 mm
- Mounting hole spacing: 16mm
- Easy to assemble.
- Lightweight so doesn't create unsuitability while operating
- Usage: Multicopter YS X4 X6 DJI Other
- Dimension:12cm x 10cm x 10cm