MY1016 250W Motor DIY E Bike Combo Kit
- Electric Bicycle permanent Magnet DC Motor MY1016.
- Rated Operating Voltage: 24VDC
- Rated speed: 2650 RPM
- Rated Current: 13.7A
- Current without load: 0.7 – 1.4 A
- Rated Torque: 8.87 Kgcm
- Rated Output Power: 250W
- Transmission :chain sprocket (11 teeth, pitch 1/4"=6,35 mm)
- Nut shaft diameter :10 mm (milled groove one-sided 1,5 mm)
MY1016Z2 250W Motor Combo for Electric Bike
- MY1016Z 24 Volt DC Operation Permanent Magnet DC Motor
- No Load RPM: 3850 RPM
- No Load Current: <2.2 Amps
- Rated Wattage: 250W (0.33 Horsepower)
- Rated Load RPM: 400
- Torque: 22 NM
- Rated Current: 13.4 Amps
- Efficiency: 78%
- Reduction Ratio: 9.78:1
- Compatible with 9 Tooth Sprocket for 1/2" x 1/8" Pitch Chain
- Chain Size: Pitch 0.5in
- Roller Diameter: 0.3in
- Roller Width: 0.16in
MY1016ZL 24V 250W Electric Wheelchair PMDC Motor with Electromagnetic Brake
- Model: MY1016ZL.
- Working voltage: 24V.
- Starting Current: 3A.
- Rated Torque: 36Nm.
- Noise: <60DB.
- Wheelchair motor output power: below 1100W.
- Operating speed: un-load 75 rpm or 120rpm;
- Reduction Ratio: 40:1.
- Installation structure: end face.
- Function type:Â wheelchair.
- Protection form: IP44.
- Insulation class: E.
- Power supply type: DC.
MY1020 Unite 36V 1000W Brushed Electric Motor
MY6812 100W 12V DC Motor for E-Bike Bicycle
MY6812 150W motor
N20 Model – 100 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Motor Type: Center Shaft DC Geared Motor
- RPM:100
- Reduction ratio - 1:298.
- Nominal Voltage - 6v
- Voltage Range - 2v to 12v
- No load Current - 80mA
- Stall Current - 1640mA
- Stall Torque - 3500 g-cm
- Ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, long lasting , not easy to wear.
- Can easily mount a wheel on the motor’s output shaft.
N20 Model – 300 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio: 1:50.
- Nominal Voltage: 6v
- Voltage Range: 3v to 12v
- RPM: 300
- No load Current: 40mA
- Stall Current: 550mA
- Stall Torque: 700 g-cm.
- Ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, long-lasting , not easy to wear.
- Can easily mount a wheel on the motor’s output shaft.
N20 Model – 40 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio: 1:380.
- Nominal Voltage: 6v.
- Voltage Range:Â 3v to 12v.
- RPM: 40.
- No-load Current: 40mA.
- Stall Current: 550mA.
- Stall Torque: 7500 g-cm.
- Ideal for making robots
- Lightweight, high torque, and low RPM.
- Fine craftsmanship, long-lasting, not easy to wear.
- Can easily mount a wheel on the motor’s output shaft
N20 Model – 500 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio - 1:30.
- Nominal Voltage - 6v
- Voltage Range - 3v to 12v
- RPM - 500
- No-load Current - 40mA
- Stall Current - 550mA
- Stall Torque - 400 g-cm
- Ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, long-lasting, not easy to wear.
- Can easily mount a wheel on the motor’s output shaft.
NANO / UNO Multi-Purpose Expansion Board
- The Sensor Shield makes your connections with the Arduino Nano much easier
- It is compatible with Arduino Nano 2.0 and 3.0
- The shield has up to 8 analogue pins, 13 digital I/O pins, and Aref with 3 pin connectors (GND, Vcc, Signal).
- Consists of an independent I2C port with 4pins (SDA, SCL, GND, and Vcc) and UART (Rx, Tx, Vcc, and GND).
- Reset button onboard and a female jack for external power supply
- Material: FR-4 Epoxy Glass Fibre Board
- IO port leads all digital and analogue IO ports, each IO port has positive and negative power supply interface standards.
- Leads to an I2C interface on the motherboard, convenient and I2C devices connected.
- Size: Approx. 57x53x8mm
