MG90S 9G Metal Gear Micro Servo Motor
- Modulation: Analog
- Gear Type: Metal
- Stall Torque@ 4.8V: 2.20 kg-cm
- Stall Torque@ 6.0V: 2.50 kg-cm
- Speed at 4.8V: 0.11 sec/60°
- Speed at 6.0V: 10 sec/60°
- Weight: 49 oz. (14.0 g)
- Dimensions: 23.1*0.48*1.14
- Rotation/Support: Dual Bearings
- Rotational Range: 180°
- Pulse Cycle: 20 ms
- Pulse Width: 400-2400 µs
BreadBoard 400 point
Arduino Nano V3.0
- Microcontroller: Atmel ATmega328 SMD Package
- Operating Voltage (logic level): 5 V
- Input Voltage (recommended): 7-12 V
- Input Voltage (limits): 6-20 V
- Digital I/O Pins: 14 (of which 6 provide PWM output)
- Analog Input Pins: 8
- DC Current per I/O Pin: 40 mA
- Flash Memory: 32 KB (of which 2KB used by bootloader)
- SRAM: 2 KB
- EEPROM: 1 KB
- Clock Speed: 16 MHz
- Automatic reset during program download
- Power OK blue LED
- Green (TX), red (RX) and orange (L) LED
- Auto-sensing/switching power input
- Small mini-B USB for programming and serial monitor
- ICSP header for direct program download
- Standard 0.1” spacing DIP (breadboard friendly)
- Manual reset switch
- Dimensions: 0.70” x 1.70”
28BYJ-48 5V Stepper motor
- High-quality stepper motor
- Voltage: DC 5V
- Diameter: 25mm
- Step Angle: 5.625 x 1/64
- Reduction Ratio: 1/64
- Rated voltage ： 5VDC
- Number of Phase ： 4
- Speed Variation Ratio ： 1/64
- Stride Angle ： 5.625° /64
- Frequency : 100Hz
- DC resistance ： 50Ω±7%(25℃)
- Idle In-traction Frequency : > 600Hz
- Idle Out-traction Frequency : > 1000Hz
- In-traction Torque >34.3mN.m(120Hz)
- Self-positioning Torque >34.3mN.m
- Friction torque : 600-1200 gf.cm
- Pull in torque : 300 gf.cm
- Insulated resistance >10MΩ(500V)
- Insulated electricity power ：600VAC/1mA/1s
- Insulation grade ：A
- Rise in Temperature <40K(120Hz
- Noise <35dB(120Hz,No load,10cm)
4 Wheel Metal Chassis Grey for Robotics
- Dimensions: 194x 104 x 48 (LxWxH).
- Weight: 270 gm.
- Material: Metal sheet.
- Colour: Grey.
- Sheet Thickness: 1.5 mm.
- Many perforated holes have given for easy attachment of development board and sensors.
- High durable, non-flexible
- Lightweight
- Can be re-shaped easily
- Resistant to corrosion
- Highly rigid
- Compatible with a single type of screw
- The chassis support one rotary castor wheel for balancing the robot & to rotate easily.
TSOP 1738 IR Receiver
- Supply Voltage: 5 V
- Operating current: 5mA
- Power consumption: 0.4 to 1.0 mA
- Ee irradiation: 0.35 mW/m2 typ.
- Angle of detection: 90
- Dimensions of the casing (mm): 12.5 x 10 x Thickness 5.8
- Temperature range: -25 C to +85 C
- Can detect IR signals from Remotes (38kHz)
- High Range and wide coverage area.
- Will respond only to IR signals, due to high immunity against ambient light
- Low power consumption
- Has in-built pre amplifier
- TTL and CMOS compatible
IR Proximity Module using TSOP
- Operating wavelength: Near-infrared region 700 nm to 1400 nm
- Main Chip: LM358
- Operating Voltage Range: 3.6V-5V DC
- Average Current Consumption: 06mA
- Distance Measuring Range: 2 to 30cm
- Detection angle: 35 °
- Easy to assemble and use
- On-board detection indication
- the effective distance range of 2cm to 80cm
- A pre-set knob to fine-tune distance range
- If there is an obstacle, the indicator lights on the circuit board
- 3mm screw holes for easy mounting
- Dimensions: 48 x 14 x 8mm
- Weight:5gm
R305 Optical Fingerprint Reader Sensor Module
- Power DC: 3.6V-6.0V
- Interface : UART (TTL logical level)/ USB 1.1)
- Working current: 100mA
- Peak Current: 150mA
- Matching mode (1: 1)
- Search method (1: N)
- Connecting cable length (cm): 8.5
- Baud rate (9600*N)bps, N=1-12 (default N=6 57600bps)
- Character file size: 256 bytes
- Image acquiring time: <0.5s
- Template size: 512 bytes
- Storage capacity: 256
- FAR : <0.001%; FRR: <0.1%
- Average searching time: < 0.8s (1:880)
- Working environment: Temp: -10degree to +40degree C
- Storage environment Temp: -40degree to +85degree C
- RH: 40%-85% RH: <85%
- Integrated image collecting and algorithm chip together, ALL-in-One.
- Low power consumption, low cost, small size, excellent performance.
- Professional optical technology, precise module manufacturing techniques.
- Good image processing capabilities can successfully capture an image up to a resolution of 500 dpi.
- Window dimension : 18mm*22mm
- Optical module: 49 x 20 x 21.20 mm
- Touch Sensors: 18 x 14.5 mm.
- Weight: 16gm
UNI T Infrared Thermometer UT30R
- Measurement range: 32 to 45 ° C.
- Resolution: 0.1 ° C.
- Test distance: 5-10 cm
- Accuracy : ± 0.3°C
- Measurement repeatability : 0.3°C
- Response time : 500 ms
- Optical measuring range : 5.5μm ~ 14.0μm
- Simple, fast and accurate IR thermometer
- Flashing arm at high temperature (more than 37.2 ° C)
- Single button operation
- LCD display with backlight for dark condition
- Auto data hold for 8s
- Auto power off
- Low voltage indication
- Option of Celsius/Fahrenheit
- Power-off memory function
General Purpose PCB 6×4
Advance Metal Chassis 1
- Dimensions: 115mm x 105mm x 45mm
- Weight: 200 gm
- Material: Metal sheet
- Color: Red.
- Sheet Thickness: 1.5 mm.
- Motor Fitting Hole Diameter: 13.75 mm.
- Many perforated holes have given for easy attachment of development board and sensors.
- Center Shaft gear motor and side shaft gear motor can be used for this chassis.