UNO R3 +WiFi ATmega328P+ESP8266 Module CH340G Compatible For Arduino Uno
- Microcontroller: ATmega328IC
- Wi-Fi: ESP8266
- USB-TTL converter: CH340G
- Power Output: 5V-800mA
- Power input USB: 5V (500mA max.)
- Power input VIN/DC Jack: 9-24V
- Power Consumption: 5V 800mA
- Logic Level: 5V
- WiFi: 802.11 b/g/n 2.4 GHz
- USB type: Micro USB
- USB Clock Frequency: 16MHz
- Operating Supply Voltage: 5V
- Digital I/O Pins: 14
- Analog I/O pins: 6
- Memory Size: 32Mb
- Interface Type: serial
- Operating temperature: −40С°/+125С°
- Dimensions (L×W)mm: 53.34×68.58
UNO R3 Transparent Case
- Material: A grade acrylic sheet.
- For Arduino UNO R3 Development Board only.
- With screw copper pillar and installation instructions.
- To protect your little computer against damages, dust and scratches Clear Top and Bottom.
- This case provides easy access to all ports.
- It requires no tools for easy assembly and disassembly.
- Simply Clicks Together Enclosure.
USB 2.0 Type A Male to USB A Male Cable
- USB 2.0
- Length:1m
- A-A male cable type
- Blue colored cable
- Standard USB 2.0 cable assembly, Type A male to type A male
- signaling rate: 480 Mbit/s (60 MB/s) Connector Type: USB 2.0 Type A Male to Type A Male
- High quality USB 2.0 high speed cable. Usually used for some external drive enclosures or cameras.
- Fully Compatible with USB 1.0,1.1 , Supports data transfer rate at up to 480Mbps
- Supports plug play connections for devices such as external hard drives, modems, printers, scanners, VOIP devices other USB peripherals.
- It is plug & play and hot swappable (no need to turn off your PC to plug a device in or out).
USB A TO B CABLE 30CM CABLE FOR UNO R3
USB A TO MICRO 30CM CABLE FOR NODEMCU
USB A TO MINI 30CM CABLE FOR NANO
USB AVR ISP 10 Pin Programmer | ATmega8 USB Programmer
- Allows you to read or write the microcontroller EEPROM, firmware, fuse bits and lock bits
- Support for Linux, Mac OS X and Windows XP,7,8
- 5 KB/sec maximum write speed
- Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
- 10 pin ISP interface
- Works under multiple platforms. Linux, Mac OS X and Windows are tested.
- Software controlled SCK option to support targets with low clock speed (less than 1.5MHz).
- 6 Pin Adapter board along with the programmer for Standard ISP connections.
- B-type USB Connector for power.
- Separate Two Different leds for power & programmer status.
USB Blaster ALTERA CPLD/FPGA Programmer
- Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data.
- Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000, and MAXII.
- FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K, and FLEX10K, etc.
- Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc.
- Enhanced configuration devices: EPC1, EPC4.
- Supports 3 download modes: AS, PS, and JTAG.
- Support and Nios II embedded soft core processor communication and debugging Rev.C latest version Hardware. Support jtag_uart.
- Speed is 6 times faster than parallel port download cable ByteBlasterII.
- Easy to use: MiniUSB interface, easy connection, two status indicator makes debugging more comfortable.
- Fully compatible with ALTERA USB Blaster, functionality and performance are the same as ALTERA original download cable.
- Operating Voltage: 1.5～5V JTAG IO Voltage.
- System configuration: Windows XP, Windows Vista, Windows7, USB interface.
USB Charger Doctor
- Display data: Voltage Current
- Operating Voltage: 3.5 to 7 V
- Maximum Current: 3 A ( accuracy of 0.4% )
- Battery Capacity (0-99999mah)
- Working time (0-99Hour)
- Charger voltage compliance DC 5V
- Resolution : Voltage 10mV current 1mA
- Error : voltage <± 1% current <± 2%
- USB Plug: 13mm / 0.5"
- RTZ, Reset button, press it three seconds will Reset
- The working time and Capacity have a Memory function when power is off.
- Compact and easy to carry, no additional power supply, plug, and play
- Detect any USB charger such as PC USB, home charger, car charger
- Easily measures the output voltage of the USB port and the device operating current or load voltage
- Dimensions: 21mm x 53mm x 15mm
- Weight: 16.2gm
USB Control Module 1 Channel 5V Relay Module (No Need Driver)
- Contact type: NC / COM / NO
- Input current: ≥300mA
- Input voltage: DC 5V
- Support Win7, XP 32-bit systems
- Onboard square USB interface, stable connection.
- Use an imported high-performance USB control chip.
- Application code: Green indicates that the relay is closed, the red disconnect
- Military-grade PCB board production
- Using genuine Single relay, the module uses HID technology, without any driver on the windows system plug and play, easy to use and simple
- Military-grade PCB board production
- Board power outlets and terminals, two kinds of access to power is flexible. After connecting the power, even if the computer is off or unplug the USB from the computer, the relay can also remain set.