DC 48V 750W BM1418ZXF Brushless Motor, Electric Bicycle Kit, DIY E-Tricycle
350W 24V Electric Bike Bicycle Rear wheel Hub motor DIY Conversion Kit
250W 36V Electric Bike Bicycle Rear wheel Hub motor DIY Conversion Kit – Basic
Pixhawk 2.4.8 Drone Flight Controller PX4 32 Bit Autopilot
- The advanced 32-bit ARM CortexM4 high-performance processors; can run NuttX RTOS real-time operating system.
- 14 PWM / servo output.
- Bus interface (UART, I2C, SPI, CAN).
- The integrated backup power and backup controller fails; the primary controller fails over to the backup control is safe.
- Provide automatic and manual modes.
- Provide redundant power input and failover.
- Multicolor LED lights.
- Provide a multi-tone buzzer Interface.
- Micro SD card to record flight data.
- 32bit STM32F427 Cortex M4 core with FPU.
- 32-bit STM32F103 failsafe co-processor.
- 168 MHz.
- 128 KB RAM.
- 2 MB Flash.
- ST Micro L3GD20H 16 bit gyroscope.
- ST Micro X4HBA 303H 14-bit accelerometer/magnetometer.
- Invensense MPU 6000 3-axis accelerometer/gyroscope.
- MEAS MS5607 barometer.
- 5* UART, 1*compatible high voltage, 2*hardware flow control
- 2*CAN
- Spektrum DSM/DSM2/DSM-X satellite receiver compatible input
- Futaba SBUS compatible input and output
- PPM signal input
- RSSI (PWM or voltage) input
- I2C
- SPI
- 3.3 and 6.6VADC
- input External USB MICRO interface
- Color:Black
- Size: 50x81x16mm
Waveshare 10.1inch HDMI LCD (B) (with case) 1280×800 IPS
- IPS screen,1280×800 high resolution
- Capacitive touch control supports up to ten-points touch
- When works with Raspberry Pi, supports Raspbian, Ubuntu, single touch, and driver free
- When working as a computer monitor, supports Windows 10/8.1/8/7, ten-points touch, and driver free
- Supports Banana Pi, Banana Pro, comes with Lubuntu, Raspbian images
- Supports BB Black, comes with Angstrom image
- HDMI interface for displaying, USB interface for touch control
- Supports 5-level backlight adjustment.
- Case Material: high-quality black Acrylic
- Comes with a back holder, 45degree tilt angle
- Dimensions: 18 x 10 x 9 cm
- Weight: 800gm
Raspberry Pi 4 (4GB)
- Broadcom BCM2711, Quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz
- 2GB, 4GB or 8GB LPDDR4-3200 SDRAM (depending on model)
- 4 GHz and 5.0 GHz IEEE 802.11ac wireless, Bluetooth 5.0, BLE
- Gigabit Ethernet
- 2 USB 3.0 ports; 2 USB 2.0 ports.
- Raspberry Pi standard 40 pin GPIO header (fully backward compatible with previous boards)
- 2 × micro-HDMI ports (up to 4kp60 supported)
- 2-lane MIPI DSI display port
- 2-lane MIPI CSI camera port
- 4-pole stereo audio and composite video port
- 265 (4kp60 decode), H264 (1080p60 decode, 1080p30 encode)
- OpenGL ES 3.0 graphics
- Micro-SD card slot for loading operating system and data storage
- 5V DC via USB-C connector (minimum 3A*)
- 5V DC via GPIO header (minimum 3A*)
- Power over Ethernet (PoE) enabled (requires separate PoE HAT)
- Operating temperature: 0 – 50 degrees C ambient
Antec HCG850 Bronze 80 Plus Bronze Certified 850 Watt Fully Modular Gaming Power Supply
200W Electric Wheelchair Powertrain PMDC Motor – SCD1
- Operating Voltage: 24VDC
- Output Power: 200W
- No-load Current: 3.6A
- Motor Speed ±5% : 3250 RPM
- No-load Output Speed: 190RPM
- Gear Ratio: 19 : 1
- Sound Level: 70 dB(A)
- Brake Torque: 33.4 Nm
- Gear Motor Rated Torque: 16.95 Nm
- Output Shaft OD: 17mm (with 6mm keyway and key)
- Weight: 15.5lbs per motor
- Efficiency : 80%
DC 48V 750W BM1418ZXF Brushless Motor, Electric Bicycle Kit, DIY E-Tricycle
3 Axis 2418 Mini DIY CNC Machine (Unassembled)
- Color: Silver
- Material: Aluminum Alloy
- Frame Size: Approx. 330 x 340 x 240mm
- Working Area: Approx. 240 x 180 x 40mm
- Control Software: GRBL control
- Spindle: 775 spindle motor(12-36V), 24V: 7000r/min, 36V: 9000r/min
- Step Motor: 1.3A 0.25N.m
- Power Supply: 24V 5.6A
- Supported System: Windows XP/ Win 7/ Win 8/ Win 10/ Linux
- Drill Bits Diameter: 3.175mm
- Drill Bits Length: 30mm
- Drill bits tip: 0.1mm
- Engraving materials: Plastic, wood, acrylic, PVC, PCB, and other soft materials.
- Laser tube: 500mw.
- Weight: 5.5KG
CNC 1610 3 Axis Mini DIY Router Wood Engraving Cutting Milling Engraver (Unassembled)
- Control software: GRBL control.
- Construction: Aluminum + plastic.
- Working area: 160*100*40mm.
- Frame size: 260*240*220mm.
- Spindle: 775 spindle motor (12-36V) 24V: 7000r/min, 36V: 9000r/min.
- Step motor: 1.3A 0.25N.m.
- Wire rod: T8.
- Power Supply: 24V 5.6A (110V -240V).
- Support System: Windows XP / Win 7 / Win 8 / Linux.
- Standard: The complete set of the parts and tools.
- Engraving materials: Plastic, wood, acrylic, PVC, PCB, and other soft materials.
- Laser tube: 500mw.
- Weight: 5.5KG.
ELECTRIC WHEELCHAIR POWERTRAIN PMDC MOTOR – SCD2-B 200W
- Operating Voltage: 24VDC
- Output Power: 200W
- No-load Current: 3.6A
- Motor Speed ±5% : 4400 RPM
- No-load Output Speed: 135RPM
- Gear Ratio: 32 : 1
- Sound Level: 60 dB(A)
- Brake Torque: 33.4 Nm
- Gear Motor Rated Torque: 16.95 Nm
- Output Shaft OD: 17mm (with 6mm keyway and key)
- Dimensions (1) : 325mm
- Dimensions (2) : 82mm
- Motor OD: 79mm
- Weight: 15.5lbs per motor
- Efficiency : 80%