3A Push to ON Pushbutton Momentary Switch
3A Push to ON Pushbutton Momentary Switch Medium
3A SPST ON OFF Pushbutton Switch
3A SPST ON OFF Pushbutton Switch Square Knob
3A SPST ON OFF Rocker Switch
3A SPST ON OFF Spring Return Rocker Switch
3BR1765JZ Offline SMPS Current Mode Controller IC
- Offline SMPS Current Mode Controller
- Drain Voltage: 650V
- Supply Voltage: 25V
- Supply Current: 5mA
- 650V avalanche rugged CoolMOS® with built-in Startup Cell
- Active Burst Mode for lowest Standby Power
- Â Fast load jump response in Active Burst Mode
- 65kHz internally fixed switching frequency
- Auto Restart Protection Mode for Overload, OpenLoop, VCC Undervoltage, Overtemperature & Overvoltage
- Â Built-in Soft Start
- Â Built-in blanking window with extendable blanking time for short duration high current
- Â External auto-restart enable pin
- Max Duty Cycle 75%
- Overall tolerance of Current Limiting < ±5%
- Â Internal PWM Leading Edge Blanking
- BiCMOS technology provide wide VCC range
- Built-in Frequency jitter and soft driving for low EMI
3D E3D V6 All Metal J-Head Hotend Extruder 1.75mm Filament 0.4mm Nozzle with Fan Duct
- Nozzle: 0.4mm
- Filament: 1.75MM
- Thermistor:100K NTC B 3950 ±1 %, 1m long wiring
- Heater: Ceramic heater 12V 40Watt. 1M long wiring
- High-Temperature Performance
- Easy No-solder, No-tape, No-adhesive Assembly And Maintenance
- Print The Widest Range Of Materials Possible
- High-Quality Printing
- Adaptable To Suit Your Needs
- Easy Mounting And Community Support
3D printer 128×64 Smart LCD controller for ramps 1.4
- RAMPS 1.4 LCD 12864 intelligent controller.
- With an SD card base on back.
- Large screen display 128×64 LCD (3.2″)
- SD card slot at the back, able to directly select a file and print
- The product comes encoder parameter adjustment can be achieved, and the file selection print
- Plug & play on the RAMPS, but need to modify the firmware to support.
- LCD 12864 Smart Controller fully supported by Marlin Firmware.
- Large screen display 128×64 LCD (3.2″)
- SD card slot at the back, able to directly select a file and print
- The product comes encoder parameter adjustment can be achieved, and the file selection print
- Plug & play on the RAMPS, but need to modify the firmware to support.
- LCD 12864 Smart Controller fully supported by Marlin Firmware.
3DBi Magnetic Mount GSM Antenna
3DOF ROBOTIC ARM SG90 DIY KIY
3DR Single TTL MINI Radio Telemetry 433MHz 250mW for PIXHAWK and APM
- MAVLink protocol framing status documents.
- Frequency modulation and Spread Spectrum (FHSS).
- Self-adaption to time-division multiplexing.
- Support LBT and AFA.
- Configurable duty cycle.
- Built-in error correcting code(up to 25% data bit error).
- AT command configures data transmission.
- RT command remote control data transmission.
- Interchangeable air and ground 433MHz modules.
- Micro-USB port.
- 6-position Molex connector.
- 250mW maximum output power (adjustable).
- SMA connector.
- 2-way full-duplex communication through adaptive TDM.
- UART interface.
- Transparent serial link.
- Open-source SIK firmware.
- Configurable through *Mission Planner and *APM Planner.
- Featuring a SiLabs Si1000 RF Microcontroller
- Support OTG of Android Cellphone and Compute
- Based on the Hope RF HM-TRP radio Module,