JF-0630B DC 24 V 300mA 10mm 6N Push Pull Solenoid Electromagnet
- Model: JF-0630B
- Rated Voltage: DC 24V
- Type: Pull Push
- Rated Current: 300mA
- Force & Stroke: 6N/10mm
- Body Size: 30 x 20 x 18mm
- Plunger Bar Size : 7 x 58mm
- Mounting Hole Diameter: 2.5mm
- Cable Length: 19cm
- Weight: 46g
- Iron Body Material
- High quality ultra-compact electric lock.
- Rustproof, durable, safe, convenient to use.
- Suction tightly sucks the iron, thus locking the door.
- Designed with the open frame type and mount board, high power.
- being installed in the escape door or fire door electronic controlled system.
- Adopts the principle of electric magnetism, when the current through the silicon, the electromagnetic lock will achieve a strong
NEMA 17 1.6 kgcm
- Operating Voltage : 12~16 V
- Step Angle : 1.8°
- Holding Torque : 1.6 KgCm
- Operating Voltage : 12 - 16 volts
- Supply Current (A) :0.31 Ampere
- Number of Leads : 6
- Frame Size (mm) : 42 x 42
- Shaft Diameter (mm) : 5
- Shaft Length (mm) : 20
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
12 V 10W Solar Panel
- Output Power: 10 Watts
- Operating Voltage: 12 Volt
- Panel Technology: Poly Crystalline
- Performance Warranty:25 Years
- Wattage (Wp): 20
- Voltage at Max Power: 16.25 volts
- Current at Max Power: 0.59 amps
- Open Circuit Voltage: 20.9volts
- Short Circuit Current: 0.65A
- of cells: 36
- High conversion speed, high-efficiency output.
- Excellent low light effect.
- A+ Grade, anti PID Poly Crystalline cell
- Cell Conversion efficiency > 16%
- Small Epoxy Solar Panels are simple to install or add to your existing product.
- Dimensions: 285 x 350 x 22mm
- Weight: 2.5 Kg
AC WATER PUMP
AD590 Temperature Transducer IC
- 2-Terminal IC Temperature Transducer
- Linear current output: 1 μA/K
- Wide temperature range: −55°C to +150°C
- Probe-compatible ceramic sensor package
- 2-terminal device: voltage in/current out
- Laser trimmed to ±0.5°C calibration accuracy (AD590M)
- Excellent linearity: ±0.3°C over full range (AD590M)
- Wide power supply range: 4 V to 30 V
- Sensor isolation from case
- Operating Voltage:30V
Lipo Battery Charger B3
- Input voltage: AC 110V-240V, 50~60Hz
- Charge Current: 1.2A Max
- Cell Cut Off Voltage: 4.2V ± 0.02V
- Circuit Power: 11W ± 10%
- Balance charge current: 850mA
- Display: Green & Red LED
- Built-in power supply
- Case: Plastic
- Max charge power: 10W
- Only charge for 2~3 series LiPo battery
- Automatic charge start
- Simple, reliable, and safe to use
- Dimensions: 88x57x35mm
- Weight:103gm
PIC18F4520 Microcontroller IC
- Maximum CPU Frequency: 40 MHz
- Architecture: 8 bit
- Program Memory (Flash): 32 kB
- RAM: 1536 byte
- Internal Oscillator: 8MHz, 32 KHz
- ADC: 1 (13 channels)
- of Pins: 40
- Voltage: 2V - 5.5V
- C Compiler Optimized Architecture: - Optional extended instruction set designed to optimize re-entrant code
- 100,000 Erase/Write Cycle Enhanced Flash Program Memory Typical
- 1,000,000 Erase/Write Cycle Data EEPROM Memory Typical
- Flash/Data EEPROM Retention: 100 Years Typical
- Self-Programmable under Software Control
- Priority Levels for Interrupts
- 8 x 8 Single-Cycle Hardware Multiplier
- Extended Watchdog Timer (WDT): - Programmable period from 4 ms to 131s
- Single-Supply 5V In-Circuit Serial Programmingâ„¢ (ICSPâ„¢) via Two Pins
- In-Circuit Debug (ICD) via Two Pins
- Wide Operating Voltage Range: 2.0V to 5.5V
- Programmable Brown-out Reset (BOR) with Software Enable Option
RS-37-555 Side Shaft Geared Motor – 60 rpm 12V DC
RS-37-555 Side Shaft Gear, Geared Motor 500 rpm 12v DC
RS-37 300 RPM High Torque Side Shaft DC Geared Motor
- Nominal Voltage: 12v
- Torque Rated: 39 N-cm
- Shaft Diameter: 6mm (with internal hole)
- Shaft Length:30mm
- Gearbox diameter: 37
- Length:80mm
- Voltage : 9 to 18 No-load current : 500 mA(Max)
- Load current: 3 A(Max)
- It has a sturdy construction.
- Comes with a Rear shaft for encoder mounting
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.
- Weight : 300 gms
RS-37 High Torque Side Shaft DC Geared Motor 30 RPM
- Nominal Voltage: 12v
- Torque Rated: 400 N-cm
- Shaft Diameter: 6mm (with internal hole)
- Shaft Length:30mm
- Gearbox diameter: 37
- Length:80mm
- Voltage : 9 to 18 No-load current : 500 mA(Max)
- Load current: 3 A(Max)
- It has a sturdy construction.
- Comes with a Rear shaft for encoder mounting
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.
- Weight: 300 gms