1.3″ OLED Display I2C 128*64 display module Blue 4pin
16×2 (1602) LCD Keypad Shield
- Operating Voltage:5V
- 5 Push buttons.
- RST button to reset Arduino program.
- Integrate a potentiometer for adjusting the backlight.
- Expanded available I/O pins.
- Blue light with white characters.
- Uses 4 Bit Arduino LCD Library
- Screen contrast adjustment
- Arduino Reset button
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
4 PIN 128*64 OLED 0.96” BLUE
- Super high brightness and high contrast
- Driver IC: SSD1306
- Input voltage: .3v to 6 v
- Ultra-wide viewing angle >160 degree
- Low power consumption with 0.04 W
- Support wide range of Voltage: 3.3V to 5V
- OLED self-lights, no backlight required
- Fully compatible with Arduino
- Communication via IIC, only two I/O ports
- Working temperature: -30 degree to 80 degree
- Dimension: 27*27*4.1mm
- Supported platform: Arduino, 51 series, MSP430, SCR chips
- No font is required, software takes the word MODULO
4 PIN 128*64 OLED 0.96” WHITE
- High resolution: 128*64
- Driver IC: SSD1306
- Input voltage: 3.3v to 6 v
- Ultra-wide viewing angle >160 degree
- Display color: white
- Super low power consumption
- Support a wide range of input
- Performs without the need for a backlight
- Compatible I/O level: 3.3v, 5v
- Fully compatible with Arduino
- Interface: I2C
- Working temperature: -30 degree to 70 degree
- Dimension: 9*9*9cm
- Size: 99gm
6 PIN 128*64 OLED 0.96” BLUE
- Resolution: 128*64
- Visual angle>160
- Input voltage:3.3V to 6V
- Compatible I/O level:3.3v, 5v
- Only need 2 I/O port to control
- Driver IC: SSD1306
- Module volume:27*27*4.1mm
- Working temperature: -30 degree to 70 degree
- Full compatible with Arduino
- Configured for SPI protocol and can be easily changed to IIC
6 PIN 128*64 OLED 0.96” BLUE-YELLOW
- Resolution: 128*64
- Driver IC: SSD1306
- Visual angle>160
- Input voltage: 3.3V to 5V
- Power: 0.04W
- Pixel color: Yellow(16 Rows) and Blue
- No backlight, OLED self light
- Communication via I2C
- Works with ESP8266, Arduino, Raspberry Pi, 8051, MSP420, STM32
- Module volume: 27*27*4.1mm
- Working temperature: -30 degree to 80 degree
- Configured for SPI protocol and can be easily changed to IIC
6 PIN 128*64 OLED 0.96” WHITE
- Super high brightness
- Super high contrast
- Visual angle>160
- Input voltage: 3.3V to 6V
- Compatible I/O level:3.3v, 5v
- Communication mode: SPI, only need 2 I/O port to control
- Driver IC: SSD1306
- Module volume:27*27*4.1mm
- Working temperature: -40 degree to 70 degree
- Full compatible with Arduino
- Configured for SPI protocol and can be easily changed to IIC
- Weight: 7gm
CD4054 4 Segment Liquid Crystal Display Driver IC
- 4 Segment Liquid Crystal Display Driver With Strobed Latch Function
- Supply Voltage Range: 3 to 20V
- Input Current: ±10mA
- Power Dissipation: 200mW
- Low level Output Voltage: 0.05V
- High level Output Voltage Min.: 4.95V
- Low level Input Voltage Max.: 1.5V
- High level Input Voltage Min.: 3.5V
- Propagation Delay Time Max.: 800ns
- Package: DIP-16
ESP32 LoRa SX1278 0.96 Inch Blue OLED Display BT WiFi Module for Arduino
- Operating voltage: 3.3V to 7V
- Operating temperature range: -40 ° C to + 90 ° C
- Frequency:433MHz
- Supports Sniffer, Station, softAP and Wi-Fi Direct modes
- Data rate: 150 Mbps @ 11n HT40,72 Mbps @ 11n HT20,54 Mbps @ 11g, 11 Mbps @ 11b
- Transmit power: 19.5 dBm @ 11b, 16.5 dBm @ 11g, 15.5 dBm @ 11n
- Receiver sensitivity up to – 98 dBm
- UDP continues to throughput by 135 Mbps
- Application:Camera