I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
1.3 inch I2C OLED display module
1.3-inch I2C OLED display module with high-contrast, low-power design—Arduino compatible, ideal for IoT and embedded applications.
Description
The 1.3-inch I2C OLED Display Module is a high-contrast, compact display designed for embedded systems and IoT applications. With its 1.3-inch diagonal screen and high-resolution pixels, it delivers clear text, icons, and graphics in monochrome OLED format.
The module features a 4-pin I²C interface (VCC, GND, SDA, SCL), allowing easy two-wire communication and minimal GPIO usage. It is fully compatible with Arduino, ESP32, ESP8266, Raspberry Pi, and STM32, making it ideal for displaying sensor data, system status, messages, and simple graphics in a variety of projects.
With low power consumption, wide viewing angles, and bright OLED contrast, the 1.3-inch OLED module is perfect for wearables, IoT devices, smart gadgets, and compact display projects.
Reviews (0)
Shipping & Delivery
Related products
58mm Thermal Printer (Black)
- Heavy-duty 58mm direct thermal printer
- Inbuilt Adapter
- High speed printing of 90mm / Sec
- Free Drivers, USB, Adapter and Paper Roll
- Interface: usb + cash drawer support.
- Works with windows 7 / 8 /10
- High speed printing
- Long life thermal head.
- Perfect print quality
- Low cost,Low noise, fast speed print.
- Support cashbox drive.
- Compact and lightweight,beautiful design.
- Â Built in data bumper (data received when printing).
- Interface type parallel port or serial port.
- Support to enlarge characters and adjust characters spacing for printing.
- Compatible with esc/order pos.
- Operation temperature0~50 Degree C
- Relative humidity10~80%
- Item size 12.8 * 18 * 10.8cm
Arduino CNC Shield
- Shield type:Â Arduino Nano
- Firmware:Â GRBL
- Modular stepper motor drivers:Â 3
- Limit switches:Â 6
- Micro-stepping:Â 1/16
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825, and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.51
Arduino LilyPad 328 ATmega328P Main Board 16M Compatible with Arduino
- Microcontroller: ATmega168 or ATmega328V
- Operating Voltage: 2.7-5.5 V
- Digital I/O Pins: 14
- PWM Channels: 6
- Analog Input Channels: 6
- DC Current per I/O Pin: 40 mA
- Board will run from 2V to 5V.
- The latest version of the LilyPad supports automatic reset for even easier programming.
- The back side of the LilyPad is now completely flat!
HC-06 4Pin Bluetooth Module Without Reset Switch
- Working current: matching for 30 mA, matching the communication for 8 mA.
- Dormancy current: no dormancy.
- Used for a GPS navigation system, water, and electricity gas meter reading system.
- With the computer and Bluetooth adapter, PDA, seamless connection equipment.
- Bluetooth module HC-08 Master and slave Two in one module.
- Use the CSR mainstream Bluetooth chip, Bluetooth V2.0 protocol standards.
- Potter default rate of 9600, the user can be set up.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- Security: Authentication and encryption.
- Profiles: Bluetooth serial port.
TB6560 4 Axis Cnc Controller 4 Axis Stepper Motor Driver DSP Controlled 3.5A 24V
- Rated maximum output: ± 4.5A, 40V, Peak 5A, low output impedance, source 0.5?,
- the receiving end of 0.4?, low voltage shutdown, thermal parking and circulation.
- circuit protection. After I design, you can set the current output of 0.5A 1A 1.8A 2.5A.
- 3.3A 4A 4.5A to accommodate more and different motor Current.
- The drive is suitable software mach2, mach3, (mach3 have support WIN7 system), KCAM4 like.
Reviews
There are no reviews yet.