I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-13%
5000W Thyristor Voltage Regulator, Adjust Light Speed Temperature
Original price was: ₹1,500.00.₹1,250.00Current price is: ₹1,250.00. inc. GST
10000W Original Chips Thyristor Super Power Electronic Regulator can Change Light Speed and Temperature
Original price was: ₹1,700.00.₹1,600.00Current price is: ₹1,600.00. inc. GST
5000W Super Power Thyristor Electronic Voltage Regulator, Adjust Light Speed Temperature
Original price was: ₹800.00.₹700.00Current price is: ₹700.00. inc. GST
- Operating Voltage: AC 220 VDC
- Maximum Power: 10000W
- Voltage Range: AC 0-220V (adjust temperature or light)
- Controller Size: 95.7*56.7*53.8mm
- Panel Size: 74.6*59.8*2.3mm
- Cable Length: 287mm
- New two-way high-power SCR, max current up to 80A.
- Voltage regulator with the peak voltage absorption circuit effectively protects the high-power SCR and has a longer service life.
- Built-in heat sink, thickened to increase the heat sink, good heat dissipation, easy to install.
- 57A high current terminal block, simple wiring, strong button adjustment stability.
- Omron original tact switch, Fairchild original photoelectric coupler, all metal film resistors are stable and durable.
- The value is automatically saved. After power-on, it will automatically start to the last adjusted value.
- Weight: 200gm
Description
5000W Super Power Thyristor Electronic Voltage Regulator designed specifically for Adjusting Light Speed Temperature. It comes with a new two-way large power silicon-controlled rectifier and offers a current up to 80A. Thus it is a good solution to the over-current of electric stove wire caused by low resistance during cooling. It can easily adjust the output voltage on a scale of 0-100% (nonlinear) to power electric device. These power thyristor designed with large and thick heat sink that would enhance heat dissipation. This voltage regulator adjusted with button which is much more stable than potentiometer.
The peak voltage absorption circuit that can protect the high power thyristor ensures long-life for this voltage regulator. These are very prominent and convenient devices, with 2-way high-power silicon controlled. And thus need not add any external components. SCR Voltage Regulator mainly used in water heater heat transfer, lighting dimming, small motor speed, electric iron thermostat and so on.
Application:
- The new two-way high-power SCR, with a maximum current of 80A, is an ideal solution to the problem of over-current electric wire when cooling is insufficient to generate resistance.
- For the usage of electrical appliances, easily modify the output voltage mains in any adjustment range from 0-100 percent (220V 100 adjustment points, non—). Electric furnaces, water heater heating, lights dimming, tiny motor speed control, and electric iron temperature control are just a few examples. As a result, the effects of dimming, temperature regulation, and pressure regulation can be achieved.
- Used in big appliances with fewer than 10,000 watts of electric power. Because the power has been abundant, common household appliances or small factories are suitable for usage. (Power from inductive or capacitive loads should be minimised; this regulator has a two-way high-power SCR that can be utilised without any additional components, making it highly handy and practical.)
Reviews (0)
Shipping & Delivery
Related products
40A DC MOTOR SPEED REGULATOR PWM CONTROLLER 2000W
- Speed controller model: 40A PWM DC motor speed regulator
- Operating voltage: 10V TO 50V
- Peak current: 40A
- Control power: 0.01-2000W
- Quiescent current: 0.025A
- PWM regulation: 5-100%
- PWM frequency: 12KHz
- Operating temperature: -20 degree to 40 degree Celsius
- Stability in working
- High efficiency
- potentiometer used for speed adjustability
- Dimension: 9*5.1mm
- Weight: 95gm
5pcs x NFC Sticker tags 13.56MHz ISO14443A 25mm Ntag213 RFID NFC tag
- Chip: Ntag213.
- Physical capacity: 180 bytes.
- Usable capacity: 144 bytes.
- Protocol: ISO14443A.
- Working frequency: 13.56 MHZ.
- Reading and writing distance: 1 to 5 cm.
- Reading and writing time: 1 to 2 ms.
- Working temperature: -20 to 55 degrees, the humidity of 90%.
- Erase times : > 100000 times.
- Data storage: > 10 years.
- Reading time: 100000 times.
- Diameter: 25mm.
- Materials: PE self-adhesive + coated paper.
- Manufacturer programmed 7-byte UID for each device
- Preprogrammed Capability container with one-time programmable bits
- Field programmable read-only locking function
- ECC-based originality signature
- 32-bit password protection to prevent unauthorized memory operations
- NFC Forum Tag 2 Type compliance
6-30V 1-Channel Power Relay Module with Adjustable Timing Cycle
- Operating voltage: 6 - 30V DC
- 1 Channel delay trigerred relay module
- Delay time: 0.1 second ~ 999 minutes
- Seven Segment Display
- Operating voltage: DC 6V-30V (supports micro USB 5V power supply)
- Trigger signal source: high-level trigger (3V-24V) signal ground and system to improve the system's anti-jamming capability (also short-circuit altogether)
- Output capability: it can control the device within DC 30V 5A or within AC 220V 5A
- Quiescent current: 20mA
- Operating current: 50mA
- Service life: more than 100,000 times
- Working temperature: -40°C-85°C
- With optocoupler isolation, enhanced anti-jamming capability, industrial grade circuit board, set parameters for memory after power failure.
- Dimension: 6.2 * 3.8 * 1.7cm
LOAD CELL 10 Kg
- Capacity: 10Kg
- Rated output(MV/V): 2.0±0.15
- Accuracy class: C2
- Maximum number of load cell verification intervals(N max): 2000
- Minimum number of load cell verification intervals(Vmin): E Max/5000
- Combined error(%RO): <±0.030
- Creep(%RO/30min): 0.03
- Temperature effect on sensitivity(%RO/°C): 0.0016
- Temperature effect on zero(%RO/°C): 0.003
- Zero balance(%RO): 1.0
- Input resistance(O): 402±6
- Output resistance(O): 350±3
- Insulation resistance(MO<50V>): 5000
- Recommended excitation voltage(V): 10~15
- Compensated temperature range(°C): -10~+40
- Operating temperature range(°C): -35~+80
- Safe overload(%RO): 150
- Ultimate overload(%RO): 200
- Load cell material: Aluminium
- Connecting cable: ø4.2*350mm
- Dimensions : 15.9 x 14.1 x 2.7 cm
- weight: 190gm
RFID 13.56MHz Card
- Contactless transmission of data and supply energy (no battery needed)
- Operating distance: Up to 100mm (depending on antenna geometry)
- Operating frequency: 13.56MHz
- Data transfer: 106 kbit/s
- Data integrity: 16 Bit CRC, parity, bit coding bit counting
- Typical ticketing transaction: <100 ms ( including backup management)
- User-definable access conditions for each memory block
- Data retention of 10 years.
- Write endurance 100 000 cycles
- Reading and writing distance: 2.5-10CM
- Reading and writing time: 1-2MS
- Working temperature: -20 ° -85 °
- Packaging materials: PVC, PET, 0.13 coins
- Packaging technology: ultrasonic automatic line / automatic welding
- Production standards: ISO 14443, ISO 10536
Speech Recognition System HM2007
- Input Voltage:9 to 15 V DC
- Use a commonly available 12V 500ma DC Adapter
- Output Data :8 bits at 5V Logic Level
- Any microcontroller like 8051, PIC or AVR can be interfaced to data port to interpret and implement specialized applications
- Self-contained standalone speech recognition circuit
- User-programmable
- Up to 20-word vocabulary of duration two-second each
- Multi-lingual
- Non-volatile memory back up with 3V battery on board. Will keep the speech recognition data in memory even after power off.
- Easily interfaced to control external circuits & appliances
TEC1-12715
- Model number: TEC1-12715
- Operating Voltage: 12V
- Maximum Voltage- Vmax (V) : 15V
- Maximum Current- Imax (A) : 15A
- Maximum Power : 230 W
- Power Cord: 100mm
- Internal resistance: 1.98 Ohm +/- 10%
- Life expectancy: 200,000 hours
- Failure rate based on long-time testing: 0.2%.
- Easy transition between the hot side to the cool side and vice-versa just by reversing the polarity of the supply.
- Quality tested cooling cells.
- Solid-state, vibration-free, noise-free.
- Simple to install and operate.
- Should use with a heat sink
- Temperature: 138°C
- Wire Insulation Material: Teflon
- Dimension: 40x40x4.0mm
- Weight: 29g
Reviews
There are no reviews yet.