I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-10%
SC10UU 10mm Linear Motion Bearing Slide Bushing Block
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
Black PLA 1.75 mm 1 Kg Filament For 3D Printer Wanhao
Original price was: ₹1,800.00.₹1,500.00Current price is: ₹1,500.00. inc. GST
100K ohm NTC 3950 Thermistor/Temperature Sensor for Reprap 3D printer Extruder
Original price was: ₹100.00.₹90.00Current price is: ₹90.00. inc. GST
- High-temperature Teflon wire temperature: 200 degrees
- Nominal resistance R25 (25 ℃): 100k
- Resistance accuracy: ± 1%
- B value R25 / 50: 3950k
- B value accuracy: ± 1%
- Operating temperature range: -40 ℃ ~ +300 ℃
- Dissipation power factor: ≥ 5 mW / ℃ (static air)
- Thermal time constant: ≤ 7S (static air)
- Maximum rated power: 45mW
- Wiring length: 1 meter
- Material: glass glaze film
Description
This 100K ohm NTC 3950 Thermistor/Temperature Sensor designed specifically for Reprap 3D printer Extruder or Heated Bed. This thermistor Conviniently pre-wired with 1 meter long high-temperature PTFE insulated wiring. Moreover, this offers a wide range of applications in 3d printing and often used with a heated bed or extruder. The Stainless steel tube encapsulation protects the probe from waterproof moistureproof thus prevents rust. This compact-sized, easy to install temperature sensor fairly precise ±0.5°C over much of the range.
Hence the temperature can be measured with a precision of 0.0625 C. It can give output is digitally accurate to 12 bits of precision from the onboard digital-to-analog converter. Here the NTC thermistor made up of think material with the heating rod made up of high-quality material. This temperature sensor module offers high sensitivity, and has a swift response, 1 percent, with a resistance value at 25°c= 100k. It uses adaptive thermosensitive material with high-quality wiring insulation with high temperature Teflon/ PTFE
Reviews (0)
Shipping & Delivery
Related products
AM2302 WIRED MODULE
- Low cost
- 3V to 5V power and I/O
- 5mA max current use during conversion (while requesting data)
- Good for 0-100% humidity readings with 2-5% accuracy
- Good for -40 to 80°C temperature readings ±0.5°C accuracy
- No more than 0.5 Hz sampling rate (once every 2 seconds)
- 3 wires 23cm long (9")
- Dimensions: 27x 58.75 x 13.30mm
DHT21 AM2301 Digital Temperature Humidity Sensor module SHT11 SHT15 Arduino
- Power: DC 3.3-5.2V
- Humidity: 0~99.9% RH
- Temperature: -20 ~ 60℃
- Precision: ±3% RH, ±0.5 ℃
- Output: Digital (1 wire)
- Accurate, durable and high quality
- 4 pin package
- Ultra-low power
- No additional components
- Excellent long-term stability
- All calibration, digital output
- Completely interchangeable
- Long distance signal transmission
- Relative humidity and temperature measurement
- Dimension: 60 x 27 x 14mm
DS18B20 PROBE
- Usable temperature range: -55 to 125°C (-67°F to +257°F)
- 9 to 12-bit selectable resolution
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into a chip
- Multiple sensors can share one pin
- ±0.5°C Accuracy from -10°C to +85°C
- Temperature-limit alarm system
- Query time is less than 750ms
- Usable with 3.0V to 5.5V power/data
- Each pin uses a heat-shrinkable tube to prevent short circuit, internal sealing glue.
- Stainless steel tube encapsulation waterproof moistureproof prevents rust.
- Stainless steel tube 6mm diameter by 30mm long.
- Contains DS18B20 temperature sensor.
- Uses 1-Wire interface- requires only one digital pin for communication.
- Unique 64 bit ID burned into the chip.
- Multiple sensors can share one pin.
- Temperature-limit alarm system.
- Without the external components, the unique single bus.
GY-906 MLX90614ESF Contactless Temperature Sensor Module
- Small size, low cost
- Mounted on a breakout board with two types of pins
- 10k Pull up resistors for the I2C interface with optional solder jumpers
- Easy to integrate
- Factory calibrated in wide temperature range:
- Sensor temperature: -40...+125°C
- Object temperature: -70...+380°C
- High accuracy of 0.5°C over the wide temperature range
- (0...+50°C for both Ta and To) High (medical) accuracy calibration
- The measurement resolution of 0.02°C
- Single and dual-zone versions
- SMBus compatible digital interface
- Customizable PWM output for continuousreading
- Simple adaptation for 8...16V applications
- Sleep mode for reduced power consumption
GY-906-BCC MLX90614ESF-BCC IR TEMPERATURE MODULE
- Input supply: 3V-5V
- Input current: 2mA
- Small size, low cost.
- Mounted on a breakout board with two types of pins.
- 10k pull up resistors for the I2C interface with optional solder jumpers.
- Easy to integrate
- Factory calibrated in a wide temperature range
- Mounted on a breakout board with two types of pins
- -40 degrees to 125 degrees C for sensor temperature
- -70 degrees to 380 degrees C for object temperature.
- High accuracy of 0.5C over a wide temperature range
- The measurement resolution of 0.02C
- Single and dual-zone versions
- SMBus compatible digital interface
- Customizable PWM output for continuous reading
- Simple adaptation for 8v to 16V applications
- Sleep mode for reduced power consumption
- Different package options for applications and measurements versatility
XH-W1401 12V Digital Led Thermostat Module Temperature Controller With Display
- Model: XH-W1401
- Power Supply: DC12V
- Thermostat Range: -9℃ to 99℃
- Thermostat Accuracy: 1℃
- Output : Electric relay output ,capacity 220V 10A/12V 10A
- For cooling or heating temperature control
- Simple Temperature Sensor Module with 12V Relay
- Imported High-Speed single-chip microcomputer.
- Three Display output status indicator.
- Automatically judge heating and cooling according to set temperature.
- Used in various temperature control, water temperature control, incubators, etc.
- Refresh Rate: 0.5 Sec
- Dimension:” 78*55mm
- Weight: 0.040 kg
Reviews
There are no reviews yet.