I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-13%
Buck Boost Module
Original price was: ₹500.00.₹450.00Current price is: ₹450.00. inc. GST
4mm Banana Plug To Crocodile Clip
Original price was: ₹200.00.₹150.00Current price is: ₹150.00. inc. GST
14V 1.7Amp Battery Charger
Original price was: ₹400.00.₹350.00Current price is: ₹350.00. inc. GST
Related products
Dual Micro USB 3.7v to 5V 2A Power Bank DIY 18650 LiPo Charger
- 4-level LED lamp display power, not working state intelligent automatic shutdown;
- The built-in lithium battery protection IC, over-current, under-voltage protection;
- Dual USB output ports.
- Dimensions: 68 x 34 x 9 mm (LxWxH)
- Weight: 10 gm
- Input port: MicroUSB (Andro)
- Input requirements: 5V constant voltage power supply can do charge input power, the most matching charger for 5v1a above
- Output port: USB
- Output parameters: 5V1A/5V2A
- Requirements for rechargeable batteries:
- Compatible Batteries: 18650 batteries, cell phone batteries, flat-panel batteries, MP3 batteries, etc. 3.7v-4.2V polymer Lithium battery,
Dual USB 5V 1A 2.1A Mobile Power Bank Battery Charger
- Micro USB input: 5V 1A
- Charging voltage input: 5V-6V 1A.
- Step-up voltage output: 5V 1A/2.1A (Dual output, Total 2.5A).
- USB Output: 5V 2.1A / 5V 1A(Dual USB interface)
- Charging display: intelligent digital display
- Batteries Type: liquid lithium-ion batteries (18650)
- Best for Arduino, DIY Kits, Power bank, etc.
- Protection circuit: Overcharge protection: 4.250V Overcharge protection release: 4.100V.
- Protection circuit: Over-discharge protection: 2.900V Over-discharge protection release: 3.000V.
- Idle time before LCD switch off 60secs.
- Screen size:27mm x 17mm
- Dimension: 57mm x 28mm
Lipo Battery Charger B3
- Input voltage: AC 110V-240V, 50~60Hz
- Charge Current: 1.2A Max
- Cell Cut Off Voltage: 4.2V ± 0.02V
- Circuit Power: 11W ± 10%
- Balance charge current: 850mA
- Display: Green & Red LED
- Built-in power supply
- Case: Plastic
- Max charge power: 10W
- Only charge for 2~3 series LiPo battery
- Automatic charge start
- Simple, reliable, and safe to use
- Dimensions: 88x57x35mm
- Weight:103gm
Solar Charge Controller 12v/24v 40A
- High efficiency:Â your batteries are charged quickly.
- Capacity for solar panel configurations of up to 3600 Wp.
- Suitable for AGM, gel, wet and Mastervolt Lithium Ion batteries.
- Fast and flexible setting of battery type.
- Battery temperature sensor for long lifespan.
- Automatic 12 V/24 V/48 V detection.
- Switchable output.
- Noiseless operation.
- LCD display.
- Fully protected against overtemperature, overload, high/low battery voltage, high/low PV voltage, short circuit and reverse polarity.
TP4056 Li-ion 5V/1A 18650 BATTERY CHARGER
- Input interface: Micro USB
- Input voltage: 4.5V-5.5V
- Full charge voltage: 4.2V
- Current: 1A adjustable
- Charge precision: 1.5%
- Battery over-current protection: 3 A
- The battery Under-voltage protection: 2.5 V
- Linear charging mode
- Maximum charging current output: 1000 mA
- Use mature charging chip TD4056 for simple peripheral circuits
- Good performance & high charging accuracy
- Dimension: 25*19*10m
- Weight: 16gm
TP5100 4.2v 8.4v Single Double Lithium Battery Charge Management Li-ion Battery Compatible 2A Charging Board
- Input voltage: 5-15V DC power supply.
- Charge status: full and unloaded blue lights, charging red.
- Double 8.4v / 4.2v lithium rechargeable single .
- Programmable charge current. 0. 1A-2A .
- Programmable steady precharge current 10% -100%.
- Wide operating voltage, maximum reach I8V.
- Red and green LED charge status indicator.
- Chip temperature protection, overcurrent protection, under voltage protection.
- Battery temperature protection, reverse battery shutdown, short circuit protection.
- Switching frequency 400Khz, usable inductance 20uH and more.
- PWR_ON Power battery for switching control.
USB for DIY charger 5V Step-Up Power Module Lithium Battery Charging Board
- Input Voltage:3.7V~5.5V
- Charging Current:1A(max)
- Output Current:1A(max)
- Output voltage:5V
- BAT Discharging Stop Voltage: 2.9V.
- Discharging Efficiency:85%(input 3.7V output 5V/1A).
- Charging and discharging indication.
- Internally installed charging and discharging power MOS.
- Preset 4.2V charging voltage, precision ±1%.
- Max 8uA standby current.
- Integration charging management and discharging management.
- Intelligent temperature control and overtemperature protection.
- Integration output overvoltage protection, short circuit protection, overload protection.
- Integration overcharging and over-discharging protection.
- Support trickle mode and zero voltage charging.
- When charging: red light flashing.
- Fully charged: Red light glows for a long time
Reviews
There are no reviews yet.