I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
16*2 ORANGE (LCD DISPLAY MODULE)
₹350.00 Original price was: ₹350.00.₹250.00Current price is: ₹250.00. inc. GST
- Input voltage: 4.7V TO 5.3V
- Operating voltage: 5V
- Current consumption is 1mA without backlight
- Consist of 2 rows and each row can print 16 characters
- Can display alphabets and numbers, i.e. alphanumeric
- Viewing area: 99*24mm
- Character size: 5.2*9.55mm
- Each character build by5*8 pixels
- Works on both 8 bit and 4 bit
- Used in industrial applications such as audio, automotive control panels, medical devices, and home automation products, etc.
- Operating temperature:0 degree to 50 degree Celsius
- Storage temperature: -10 degrees to 50 degree Celsius
- 1/16 duty cycle
Displaying information is one of the crucial steps in electronic projects. So using LCDs has always been one of the most popular ways to display information. 16*2 LCD module is yellow with an orange backlight display module. These are brand new and high-quality displays with orange backlight. It ensures high contrast and a wide viewing angle. This display is larger than a normal LCD display. These are big character LCD display modules with black text on the Orange background. LCD modules are the most prominent as they are low cost and program friendly, hence these modules are commonly used in the embedded system.
16*2 LCD module consists of 16 columns and 2 rows, so it has 32 (16*2) characters in total. Each character has 40pixels (5*8) and thus for 32 characters there 1280 pixels (32*40). LCD modules are the most prominent as they are low cost and program friendly, hence these modules are commonly used in the embedded system. An interface IC HD44780 is attached to the backside of the LCD module to determine the position of the pixel. This IC gets commands and data from the microcontroller and processes it, thus display it on the screen. Using a resistor or PWM the color can be dimmed easily.
It is quite simple to work with these LCDs s and they have full compatibility with all microcontrollers and processor boards. This display module works on 5V and has a white backlight which can be on or off as per requirement. This module consists of a minimum of 6 I/O pins to interface this LCD screen. Moreover, it can work in both 4 bit and 8-bit MCU interfaces.

Related products
16×2 (1602) LCD Keypad Shield
- Operating Voltage:5V
- 5 Push buttons.
- RST button to reset Arduino program.
- Integrate a potentiometer for adjusting the backlight.
- Expanded available I/O pins.
- Blue light with white characters.
- Uses 4 Bit Arduino LCD Library
- Screen contrast adjustment
- Arduino Reset button
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
20/4 GREEN (LCD DISPLAY MODULE)
- Operating voltage: 5V
- Display format: 20 characters * 4 line
- Display mode: STN or FSTN
- Dot-matrix: 5*8 dots
- Character size: 2.95 * 4.75mm
- Character pitch: 3.55 * 5.35mm
- LCD driver IC: ST7066U
- 1/16 duty cycle
- Wide viewing angle and high contrast
- Works on both 8-bit parallel interface
- Operating temperature: -20 degree to 70 degree Celsius
- Low Current consumption
- Dimension: 98*60*13.6mm
- Compact size and lightweight
3.5 Inch Raspberry Pi Display
3D printer 128×64 Smart LCD controller for ramps 1.4
- RAMPS 1.4 LCD 12864 intelligent controller.
- With an SD card base on back.
- Large screen display 128×64 LCD (3.2″)
- SD card slot at the back, able to directly select a file and print
- The product comes encoder parameter adjustment can be achieved, and the file selection print
- Plug & play on the RAMPS, but need to modify the firmware to support.
- LCD 12864 Smart Controller fully supported by Marlin Firmware.
- Large screen display 128×64 LCD (3.2″)
- SD card slot at the back, able to directly select a file and print
- The product comes encoder parameter adjustment can be achieved, and the file selection print
- Plug & play on the RAMPS, but need to modify the firmware to support.
- LCD 12864 Smart Controller fully supported by Marlin Firmware.
5” TFT for Raspberry PI
- Display Size: 5″
- Resolution: 800 x 480 pixel
- Supply Voltage: 5V @1A
- Touch: 4-wire resistive touch
- LCD DRIVER IC: ILI9486L
- Refresh rate:60HZ
- Good touch response
- Large viewing angle
- Fast response time
- Support backlight control for low power consumption
- Compatible with Raspberry Pi 3, Pi2, Model B/B+
- Not only for Raspberry Pi
- Not only for mini-PCs, it can also work as a computer monitor
- The monitor can work with standard HDMI devices (adjust output resolution to 800*480),
- Touch function is only available for Raspbian and Ubuntu systems.
- Touch panel function not supported---Retropie, Windows 10
- LCD Size:11mm*77.93mm
- Weight:175g
6 PIN 128*64 OLED 0.96” BLUE-YELLOW
- Resolution: 128*64
- Driver IC: SSD1306
- Visual angle>160
- Input voltage: 3.3V to 5V
- Power: 0.04W
- Pixel color: Yellow(16 Rows) and Blue
- No backlight, OLED self light
- Communication via I2C
- Works with ESP8266, Arduino, Raspberry Pi, 8051, MSP420, STM32
- Module volume: 27*27*4.1mm
- Working temperature: -30 degree to 80 degree
- Configured for SPI protocol and can be easily changed to IIC
6 PIN 128*64 OLED 0.96” WHITE
- Super high brightness
- Super high contrast
- Visual angle>160
- Input voltage: 3.3V to 6V
- Compatible I/O level:3.3v, 5v
- Communication mode: SPI, only need 2 I/O port to control
- Driver IC: SSD1306
- Module volume:27*27*4.1mm
- Working temperature: -40 degree to 70 degree
- Full compatible with Arduino
- Configured for SPI protocol and can be easily changed to IIC
- Weight: 7gm
PR34 2004 LCD Display Smart Controller W or Adapter for RAMPS1.4 Reprap 3D Printer
- RAMPS 1.4 2004 LCD Display intelligent controller.
- LED background light control circuit, a small function of the intelligent controller,
- With pin short time to decide on all LED turn or steering 30 seconds
- You can turn on the light time to do the long or short form of the adjustment TRIMM R4100K from 10 seconds to 2 minutes.
- Plug and play on the RAMPS, but need to modify the firmware to support.
- The product comes encoder parameter adjustment can be achieved, and the file selection print.
- With an SD card base on the back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Reviews
There are no reviews yet.