I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
434MHz/315Mz TX & RX
₹300.00 Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
Transmitter
- Working voltage: 3V – 12V for max. power use 12V
- Working current: max Less than 40mA max , and min 9mA
- Modulation mode: ASK
- Working frequency: 433MHz
- Transmission power: 25mW
Receiver
- Working voltage: 5.0VDC
- Working current:≤5.5mA max
- Modulation method: OOK/ASK
- Working frequency: 433.92MHz
- Bandwidth: 2MHz
- Sensitivity: excel –100dBm (50Ω)
- Transmitting velocity: <9.6Kbps (at 315MHz and -95dBm)
This RF module designed based on an RF Transmitter and an RF Receiver operates at a frequency of 434 MHz. An RF transmitter transmits serial data input wirelessly through its antenna connected at pin4. It transmits signals at the rate of 1Kbps – 10Kbps. The module consists of a SAW resonator tuned for 433.xx MHz operation. Moreover, there is a switching transistor and a few passive components to perform the functions.
This Radio Frequency (RF) module operates on Amplitude Shift Keying (ASK) with transmitter/receiver (Tx/Rx). The Transmitter transmits this serial input through RF. Then the Receiver module receives the transmitted signal placed away from the source of transmission. Thus these RF signals transmitted at a particular frequency and a baud rate. The RF receiver receives the transmitted data only if it operating at the same frequency as that of the transmitter. Moreover, this RF module has a wide range of applications in a Car security system, Remote key-less entry, Garage door controller, Home security, Wireless mouse, Automation system.
The transmitter module consists of an RF tuned circuit and a couple of OP Amps to amplify the received carrier wave from the transmitter. This amplified signal is further fed to a PLL (Phase Lock Loop) which enables the decoder to “lock” onto a stream of digital bits which gives better-decoded output and noise immunity.
The transmitter is powered by Vcc at a range of DC voltage between 3.5V to 12V. Since the RF output is proportional to the supply voltage. Thus higher the voltage, the greater the range will be. Finally, the antenna pin meant for an external antenna. This RF module is often used with a pair of encoder/decoder. Thus the encoder encodes parallel data for transmission feed, while the decoder decodes the receiving signal. So HT12E-HT12D, HT640-HT648, etc. are some commonly used encoder/decoder pair ICs.
Pin Description
Transmitter Module:
- Ground (0V): GND
- Serial Data Input Pin: DATA
- Supply Voltage (5V): VCC
- Antenna Output Pin: ANT
Receiver Module:
- Ground (0V): GND
- Serial Data Output Pin: DATA
- Linear Output Pin: Not Connected NC
- Supply Voltage (5V): VCC
- Supply Voltage (5V): VCC
- Ground (0V): GND
- Ground (0V): GND

Related products
1 CHANNEL 12V RELAY
- 1-Channel relay interface board
- Operating voltage: 12V DC
- Provide high current relay of 15A
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances
- LED status indicates relay ON/OFF state.
- High current relay of 10A @250 V AC/10A@ 30V DC
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 43*17*17mm
- Weight: 150gm
16 CHANNEL 5V RELAY
- 16 channel 5V relay board
- Operating voltage: 5V
- Supply current: 500mA
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- Low state voltage: 0V to 0.5V (relay is ON)
- High state voltage: 3.7V to 5V(relay is OFF)
- Single-chip design with reliable performance
- Strong anti-interferences
- Strong anti-jamming ability and stable performance
- The on-board power supply module doesn’t need any external power
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Dimension: 180*90*20mm
- Weight: 100gm
2 CHANNEL 5V RELAY
- High current relay
- Two LED S to indicate relays ON/OFF status
- Low-level trigger expansion board
- Opto isolation circuitry
- Works with logic level signal 3.3V or 5V devices
- Can be used as normally open (NO) or normally closed (NC)
- Back EMF protection
- Ensures diode current protection
- AC control voltage: 250v @mx10A
- DC control voltage: 30V @max 10A
- Easy installation and fixing
Antenna GSM-6DBI (Spring)
- Gain:6dBi
- Lower VSWR ≤ 2.0
- Signal stability.
- Cable Length: 3m
- Antenna Height: 28cm
- Polarization Vertical Impedance- 50 Ω
- Material: Metal
- Colour: Black
- Magnetic base
- Operation Temperature: -30~60 degree C
- Humidity: 5% to 95%
- Connector type: SMA Male Plug
- Compact size.
- Good appearance.
- Strong adaptability of environment.
GPS Modem SKG13C External Antenna
- Operating voltage: 3.0V to 4.2V
- Ultra high sensitivity: -165dBm
- Extremely fast TTFF (Time To First Fix) at the low signal level
- Low power consumption: Typical 45mA@3.3V
- NMEA-0183 compliant protocol or custom protocol
- Operating temperature range: -40 to 85℃
- SMD type with stamp holes
- Small form factor: 15x13x2.7mm
- RoHS compliant (Lead-free)
- Support walk model
GPS Modem with External Antenna
- SiRF Star IV™, GSD4e ROM version
- Tracking sensitivity -163dBm, autonomous Acquisition sensitivity -148dBm
- TTL interface output
- 48 track verification channels
- Power supply 3.3 voltage
- SMT type with stamp holes
- Small form factor with embedded SiRF star iv technology
- Removes in-band jumbers up to 80dB-Hz, track up to 8CW jammers
- Excellent sensitivity for urban canyon and foliage environments.
SIM28 GPS Module / Modem with GPS antenna
- Operating voltage: 12v dc.
- Compatible with TTL & serial.
- Frequency 1, 1575.42mhz
- 023mhz chip rate
- 16 channels all in view
- 6-channels GPS search engine
- Ultra-low-power design (38mA, typical)
- Compact size
- Built-in low noise, high gain active antenna
- Super-cohesive magnetic for installation
- High sensitivity (up to -152dBm typ)
- Apply to host devices with USB or RS232
Ublox NEO 7M GPS With Compass for APM 2.6/2.8 and Pixhawk 2.4.6/2.4.8
- Tracking sensitivity: 161 dBm
- Capture sensitivity : 148 dBm
- Cold start time: 38s average
- Warm start time: 35s average
- Hot start time: 1s average
- Capture time: 0.1s Average
- Locate performance
- Pre-configured, Flashed with the correct settings and tested
- Super Bright LED
- Backplane with Standard Mk style mounting holes 45mm X 45mm
- 38400 bps (Default) Changed to 115200bps!
- Output GGA, GSA and RMC frames
- 1Hz (Default) Changed to 5Hz!
- Permanent Configuration Retention
- Onboard compass
- 6 pin connector for EZ connect to MEGA BLACK
- 4 pin connector for only GPS use
- 4 pin connector for compass only use
- Can use both 4 pin at once

Reviews
There are no reviews yet.