I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-17%Sold out
2A Push to ON Pushbutton Momentary Switch Small
Original price was: ₹20.00.₹10.00Current price is: ₹10.00. inc. GST
LM336 Precision 2.5V Shunt Regulator IC
Original price was: ₹20.00.₹15.00Current price is: ₹15.00. inc. GST
ANTENNA WIFI
Original price was: ₹780.00.₹650.00Current price is: ₹650.00. inc. GST
Antenna Specifications:
- Color: Black
- Radiation: Omni-directional
- Gain:8dBi
- Frequency Range(MHz): 2400-2500, 5150-5850MHz
- Connector Type: RP-SMA Male (Hole)
- Angle Adjustable: 90° 135° 180°
- Dimension: 16cm/ 6.3”(Unbend) / 13.5cm/ 5.31”(Bend)
- Wight: 13.5g / 0.48 oz per antenna
Pigtail Cable Specifications:
- Color: Black & Gold
- Length: 15cm / 5.9”
- Wight:4.4g / 0.17 oz per pigtail cable
- Connector Type: U.FL/ IPEX to RP-SMA Female
Out of stock
Description
This flexible uFL 2.4GHz antenna is 4″ / 100mm long and has a gain of around 4DBi and a 50 impedance. As a result, it’ll function great with almost any 2.4-2.5GHz wireless receiver/transmitter. Radio waves are used by wireless devices to communicate with one another. These wireless communications are electromagnetic waves (EM waves) that contain data packets. WiFi antennas transform electromagnetic waves into electrical impulses and vice versa.
Receiving and transmitting antennas are found in wireless networking devices such as routers, cellphones, laptops, tablets, and hotspots. Receiving antennas scavenge EM waves holding data packets and turn them into electrical signals that the device can handle. The transmitting antennas, on the other hand, transform electrical impulses into EM waves in order to send the knowledge packets.
Reviews (0)
Shipping & Delivery
Related products
Antenna GSM-6DBI (Spring)
- Gain:6dBi
- Lower VSWR ≤ 2.0
- Signal stability.
- Cable Length: 3m
- Antenna Height: 28cm
- Polarization Vertical Impedance- 50 Ω
- Material: Metal
- Colour: Black
- Magnetic base
- Operation Temperature: -30~60 degree C
- Humidity: 5% to 95%
- Connector type: SMA Male Plug
- Compact size.
- Good appearance.
- Strong adaptability of environment.
ESP8266 ESP – 03 WIFI Transreceiver Wireless Module
- Communication interface voltage: 3.3V
- Working current: 240mA(MAX)
- 802.11 b/g/n
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLLs, regulators, DCXO and power management units
- +19.5dBm output power in 802.11b mode
- Power down leakage current of <10uA
- Integrated low power 32-bit CPU could be used as application processor
- SDIO 1.1/2.0, SPI, UART
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
- SDIO 2.0, SPI, UART
- 32-pin QFN package
- Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
- Integrated RISC processor, on-chip memory and external memory interfaces
- Integrated MAC/baseband processors
- Quality of Service management
- I2S interface for high fidelity audio applications
- On-chip low-dropout linear regulators for all internal supplies
- Proprietary spurious-free clock generation architecture
- Integrated WEP, TKIP, AES, and WAPI engines
ESP8266 ESP-12F
- Communication interface voltage: 3.3V
- Working current: 240mA(MAX)
- Serial port baud rate: 115200 (default), can be modified to other values by AT command
- Serial communication format: 8N1
- Wireless Network Mode: station / softAP / SoftAP + station
- Wireless criteria: 802.11 b / g / n
- WIFI @ 2.4 GHz, support for WPA / WPA2 security mode
- +19.5dBm output power
- Compatible with ESP-12（ESP-202）
- It is very easy to develop projects with AT commands
- Surface Mount Package with 2mm Pitch Pads
- Mulitple GPIO’s for all your sensor needs
- Integrated TCP/IP protocol stac
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, DCXO and power management unit
- Power down leakage current of <10uA
- Integrated low power 32-bit CPU could be used as an application processor
- SDIO 1.1/2.0, SPI, UART
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
- Both SMD and Inline package are available, and the pin pitch is 2.0mm.
ESP8266 WIFI Shield
- Operating voltage 5V (supplied from the Arduino Board)
- Connection via: 802.11b/g networks
- Encryption types: WEP and WPA2 Personal
- Connection with Arduino on SPI port
- on-board micro SD slot
- ICSP headers
- FTDI connection for serial debugging of WiFi shield
- Mini-USB for updating WiFi shield firmware
- 32-bit RISC architecture
- The processor can operate at 80MHz / 160MHz
- 32MB flash memory
- 64kB for instructions
- 96kB for data
- Operates in AP, Station or AP + Station mode
- It has 11 digital pins
- It has 1 analogue pin with 10-bit resolution
- Digital pins except the D0 have interrupts, PWM, I2C and one wire
- Programmable through USB or WiFi (OTA)
- Compatible with Arduino IDE
- Compatible with modules and sensors used in Arduino
Mini ESP-M2 ESP8285 Serial Wireless WiFi Transmission Module SerialNET MODE Fully Compatible With ESP8266
ESP8285 M2 WiFi IoT Module :
- SOC characteristics.
- Built-in Tensilica L106 ultra-low power 32-bit CPU, main frequency supports 80MHz and160MHz and RTOS.
- Built-in TCP/IP protocol.
- Built-in one-channel 10-bit high precision ADC.
- Outboard interface: HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO.
- The deep sleep current is 10uA, the cut-off current is smaller than 5uA.
- Wake, connect and transmit data package within 2ms.
- The consumer power is smaller 1.0Mw (DTIM3) when at standby status.
- Built-in 1M byte for SPI Flash.
- Ultra-small size.
- Support serial to WiFi.
- Wireless transparent transmission.
- Long-distance transmission with ultra-low power.
- Support outboard antenna.
- Bearing high temperature to 125 °C, compared to the 85°C for ESP8266.
- Support 802.11 b/g/n/e/I.
- Support Station, Soft AP, Soft AP+STA mode.
- Support WiFi Direct (P2P).
- Support CCMP (CBC-MAC, computation mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc., for hardware acceleration.
- P2P finding, P2P GO mode/ GC mode and P2P power management.
- WPA/PA2PSK and WPS.
- 11securitycertification: pre-certification and TSN.
- Support 802.11n (2.4GHz).
- 1h/RFC1042 frame encapsulation.
- Support seamless roaming.
- Support AT remote update and cloud update (OTA).
- Support Smart Config function (including Android and Ios device
Mini SMD NRF24L01 2.4G Wireless Data Transmission Module
- Maximum operating speeds up to 2Mbps
- GFSK modulation efficiency, Anti-interference ability,
- Built-in hardware CRC error detection, Multipoint communication address control.
- Low-power 1.9 to 3.6V, only 1uA on Power-down mode
- Built-in 2.4Ghz antenna
- Built-in voltage regulator
- 125 Channels, Multi-point communication, and frequency hopping to meet the communication needs
- Wireless transceiver including Frequency generator, enhanced type, SchockBurstTM, mode controller, power amplifier, crystal amplifier, modulator, demodulator
- The output power channel selection and protocol settings can be set extremely low current consumption, through the SPI interface
- In the transmit mode, the transmit power is 6dBm, the current is 9.0mA, the accepted mode current is 12.3mA, the current consumption of the power-down mode and standby mode are lower
- Standard DIP Pitch Interface for embedded applications.NRF24L01 SPI interface: hardware SPI port, MCU I/O ports
- Internal FIFO compatible with a variety of microprocessor interface, micro-controller is convenient
Mini Ultra-small Size ESP-M3 From ESP8285 Serial Wireless WiFi Transmission Module Fully Compatible With ESP8266
- Model: ESP8285 ESP-M3
- 32-bit Tensilica L106 microcontroller
- Ultra-low 16 bit RISC
- Fully Compatible with ESP8266
- Embedded TCP protocol
- channel high-precision 10-bit ADC
- Supporting the most commonly used networks (802.11 b / g / n)
- Support WPA, PA2PSK and WPS
- Working temperature: -40 ℃ - + 125 ℃
- Clock Speed: 80 MHz; (max 160 MHz)
- Flash memory: 1 MB
- Interface: HSPI, UART, I2C, I2S, Remote Control IR Control, PWM, GPIO
- Direct WiFi Support (P2P)
- Support mode: CCMP, TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc
- Low consumption
- Easy access to the pins
NODMCU Esp8266-12 USB CP2102
- 11 b/g/n Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- CP2102 Serial / USB Chip
- +19.5dBm output power in 802.11b mode
- 4MB Flash Memory
- Integrated low power 32-bit CPU
- SDIO 1.1 / 2.0, SPI, UART
- Dimensions – 49 x 24.5 x 13mm
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLLs, regulators, DCXO and power management units
- On board USB to serial chip to easily program and upload codes from the Arduino IDE
- Embeds logic level converter circuits
- Has on board 3.3V regulator to ensure enough power to function as your go-to WiFi chip!
- Easy access to the GPIO pins for easy prototyping
- ESP-12E Processor
- Easy to use breadboard friendly form factor
- Voltage Regulator / Converter, excellent DC to DC conversion, super efficientESP-12E Processor
- Easy to use breadboard friendly form factor
Reviews
There are no reviews yet.