I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
BD135 NPN Transistor 45V 1.5A
₹11.00 Original price was: ₹11.00.₹6.00Current price is: ₹6.00. inc. GST
- Collector-base Voltage:Â 45V
- Collector Current:Â 1.5A
- Transistor Polarity:Â NPN
- Total Power Dissipation:Â 12.5W
- Current Gain max. :Â 250
- Package:Â T0-126
This BD135 NPN bipolar transistor designed explicitly for use in general-purpose low power silicon NPN bipolar junction transistors. The BD135 offers exceptional high gain performance along with a very low saturation voltage. BD135 comes in a three terminal NPN device within the working range. The collector current IC is a function of the base current IB. Any change in the base current cause corresponding amplified change in collector current for a given collector emitter voltage VCE.
The most crucial component in an electrical circuit is the transistor. Two pieces of P-type silicon (the base) are placed between two pieces of N-type silicon in an NPN transistor (the collector and emitter). The main purpose of these transistors was to transport electrons from the emitter to the collector (so conventional current flows from collector to emitter). The emitter “emits” electrons into the base, and the base controls the amount of electrons the emitter emits. These electrons are transferred to the collector after mixing with the holes in the base. The collector “collects” and sends the bulk of the liberated electrons to the next section of the circuit.
The purpose of the NPN transistor is to amplify weak signals that enter the base and create powerful amplify signals at the collector end. The travel of an electron in an NPN transistor is from the emitter to the collector area, resulting in current in the transistor. Because the bulk of charge carriers in such transistors are electrons, which have a higher mobility than holes, they are commonly utilised in circuits. The emitter, collector, and base of an NPN transistor are the three terminals. The centre part of an NPN transistor is weakly doped, and it is the most critical factor in the transistor’s operation. Meanwhile, the emitter was little doped, whereas the collector was extensively doped.

Related products
1/4W 5% Assorted Value Carbon Film Resistor Assortment Kit Set pack electronic diy kit
- 100% brand new and high quality.
- Fine workmanship and long service life.
- 1/4W carbon film resistor package.
- High precision and stability.
- Easy to use.
- Precision: 5%
- Error: 5%
- Values
- 10Ω, 15Ω, 22Ω, 33Ω, 47Ω, 68Ω, 100Ω, 220Ω, 330Ω, 470Ω, 1k, 1k5, 2k2, 3k3, 4k7, 5k6, 6K8, 8K2, 10K, 15K, 22K, 33K, 47K, 56K, 68K, 100K, 150K, 220K, 330K, 470K
- Package included: 150pcs
120pcs 12 values 0.22UF-470UF Aluminum electrolytic capacitor assortment kit set pack
25pcs Button Switch Kit
- Relative Humidity: 95%
- Rated Voltage: 12V
- Rated Current: 50 mA
- Contact resistance: 50M Ohm Max (initial)
- The insulation resistance: 100M Ohm minDC (250V)
- The compressive strength: AC250V (50/60Hz for 1 minute)
- Mechanical life: 100000 cycles
- The environment temperature: 25° ~ + 105°
- The operating strength: 180/250 (plus or minus 30gf)
- Dimension: 12 * 12 * 7.3 round convex type
- Total Buttons: 25pcs
- Colours: 5 (Black, Red, White, Blue, Yellow)
AP Extension pigtail SMA female socket jack to UFL IPX Connector
GSM Antenna
IR LED Sensor
- Size: 5mm LED
- Wavelength: 940nm wavelength (most commonly used)
- Forward current (IF) is 100mA (normal condition) and 300mA (max.)
- 5A of surge forward current
- 24v to 1.4v of forward voltage
- Temperature : -40 to 100 ℃
- Soldering Temperature should not exceed 260 ℃
- Power Dissipation of 150mW at 25℃ (free-air temperature) or below
- Spectral bandwidth of 45nm
- Viewing angle: 30 to 40 degree
- High Reliability
- Excessive radiant intensity
- Having lead spacing of 2.54mm
- Easy to use with breadboard or perf board
TP5100 4.2v 8.4v Single Double Lithium Battery Charge Management Li-ion Battery Compatible 2A Charging Board
- Input voltage: 5-15V DC power supply.
- Charge status: full and unloaded blue lights, charging red.
- Double 8.4v / 4.2v lithium rechargeable single .
- Programmable charge current. 0. 1A-2A .
- Programmable steady precharge current 10% -100%.
- Wide operating voltage, maximum reach I8V.
- Red and green LED charge status indicator.
- Chip temperature protection, overcurrent protection, under voltage protection.
- Battery temperature protection, reverse battery shutdown, short circuit protection.
- Switching frequency 400Khz, usable inductance 20uH and more.
- PWR_ON Power battery for switching control.
XT60 Connector
- Manufacturer: AMASS
- Connector Series: XT60H
- Rated Voltage: DC 500V
- Metal Material: Brass Gold Plated
- Rated Current: 30A
- Momentary Current: 60A
- Number of pins: 2
- Colour: Yellow
- Contact Resistance: 0.55mΩ
- FR Level: UL94 V0
- Use Times: 1000 TIMES
- Temperature: -20℃ to 120℃
- Spatial Orientation Straight
- Compatible for Wire size up to 12AWG
- Mechanical mounting for cable
- Electrical mounting soldered
- Contact plating Gold flash

Reviews
There are no reviews yet.