I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-11%
BH1750
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
DHT11 MODULE
Original price was: ₹250.00.₹150.00Current price is: ₹150.00. inc. GST
CJMCU Guva S12SD Sunlight Ultraviolet UV Ray Intensity
Original price was: ₹650.00.₹580.00Current price is: ₹580.00. inc. GST
- Power supply voltage of 2.5 V ~ 5 V
- Low power consumption
- Wide detection range: 240 nm to 370 nm
- Wide Angle: 130 degrees
- Schottky type photosensitive diode
- Good linear response
- High sensitivity
- Low power consumption
- Power supply voltage of 2.5 V ~ 5 V
- Working current is microamps.
- High sensitivity
- High stability
- Wide detection range: 240 nm to 370 nm
- Wide Angle: 130 degrees
- Schottky type photosensitive diode
- Dimension: 11 mm x 27 mm
Description
The GUVA-S12SD UV Sensor chip is a microcontroller-compatible module used for detecting the intensity of UV radiation in sunlight. These are widely used in any application where we want to monitor the amount of UV light and is simple to connect to any microcontroller through one ADC channel.
This module operates with a typical UV detection wavelength of 200 – 370nm, then outputs a calibrated analogue voltage that varies with the UV light intensity. The UV Sensor module is based on the renowned sensor GUVA-S12SD. This is a Gallium Nitride material based Schottky-type photodiode, designed for photovoltaic mode operation. The other main component is an Op-Amp IC SGM8521 which is a rail-to-rail input and output voltage feedback amplifier offering low cost. Thus Op-Amp offers a wide input common-mode voltage range and output voltage swing. It also takes the minimum operating supply voltage down to 2.1V and the maximum recommended supply voltage to 5.5V. Moreover, SGM8521 provides 150 kHz bandwidth at a low current consumption of 4.7 µA.
The module provides a standard, right-angled, 3-pin male-header interface connection:
- GND: 0V (Ground connection)
- VCC: 3.3V to 5.5V (5mA current consumption)
- OUT: 0V to 1V ( 0 to 10 UV Index)
Application:
- Uv tester
- UV watches
- outdoor sports equipment
- mobile phone, etc
Reviews (0)
Shipping & Delivery
Related products
16 CHANNEL 5V RELAY
- 16 channel 5V relay board
- Operating voltage: 5V
- Supply current: 500mA
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- Low state voltage: 0V to 0.5V (relay is ON)
- High state voltage: 3.7V to 5V(relay is OFF)
- Single-chip design with reliable performance
- Strong anti-interferences
- Strong anti-jamming ability and stable performance
- The on-board power supply module doesn’t need any external power
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Dimension: 180*90*20mm
- Weight: 100gm
2 CHANNEL 5V RELAY
- High current relay
- Two LED S to indicate relays ON/OFF status
- Low-level trigger expansion board
- Opto isolation circuitry
- Works with logic level signal 3.3V or 5V devices
- Can be used as normally open (NO) or normally closed (NC)
- Back EMF protection
- Ensures diode current protection
- AC control voltage: 250v @mx10A
- DC control voltage: 30V @max 10A
- Easy installation and fixing
4 CHANNEL 12V RELAY
- 4-Channel relay interface board
- Relay input voltage: 12V DC
- Relay output: 5A/250V AC
- Signal input:5V DC from the microcontroller
- High current relay of 10A @250 V AC/10A@ 30V DC
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances such as DC motors, solenoid valves, lamps, etc.
- LED status indicates relay ON/OFF state.
- Power battery terminal for relay output and aux power connection
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- Relay can directly control all equipment’s and loads
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 165*65*1mm
- Weight: 7gm
DS3231 RTC MODULE
- Operating voltage of DS3231: 2.3 v to 5.5v
- 400Khz I2C interface
- Automatic power failure battery switch circuitry
- RTC counts seconds, minutes, hours, and year
- High precision clock chip DS3231
- Programmable square-wave output
- Chip temperature sensor accuracy:+/_3 degree Celsius
- Memory chip: AT24C32 with 32K storage capacity
- CR2032 battery backup with a high life span
- Low power consumption
- Register for ageing trim
- Dimension: 38mm*22mm*14mm
LDR SENSOR 5mm
MOQ: 2 nosÂ
- Â No. of Pins: 2
- Â Type of Mounting: PCB Through Hole
- Â Maximum Operating Temperature: +800C (Approx.)
- Â Dark resistance:1-20M ohm
- Good reliability
- High sensitivity
- Fast response
- Good spectrum characteristic
- Size: 5mm (50-paise size)
- .Coated with epoxy
- Miniature open frame package.
- Proxy coated.
- Moisture resistant.
- Spectral response is similar to the human eye.
Reviews
There are no reviews yet.