I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-11%
BH1750
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
DHT11 MODULE
Original price was: ₹250.00.₹150.00Current price is: ₹150.00. inc. GST
CJMCU Guva S12SD Sunlight Ultraviolet UV Ray Intensity
Original price was: ₹650.00.₹580.00Current price is: ₹580.00. inc. GST
- Power supply voltage of 2.5 V ~ 5 V
- Low power consumption
- Wide detection range: 240 nm to 370 nm
- Wide Angle: 130 degrees
- Schottky type photosensitive diode
- Good linear response
- High sensitivity
- Low power consumption
- Power supply voltage of 2.5 V ~ 5 V
- Working current is microamps.
- High sensitivity
- High stability
- Wide detection range: 240 nm to 370 nm
- Wide Angle: 130 degrees
- Schottky type photosensitive diode
- Dimension: 11 mm x 27 mm
Description
The GUVA-S12SD UV Sensor chip is a microcontroller-compatible module used for detecting the intensity of UV radiation in sunlight. These are widely used in any application where we want to monitor the amount of UV light and is simple to connect to any microcontroller through one ADC channel.
This module operates with a typical UV detection wavelength of 200 – 370nm, then outputs a calibrated analogue voltage that varies with the UV light intensity. The UV Sensor module is based on the renowned sensor GUVA-S12SD. This is a Gallium Nitride material based Schottky-type photodiode, designed for photovoltaic mode operation. The other main component is an Op-Amp IC SGM8521 which is a rail-to-rail input and output voltage feedback amplifier offering low cost. Thus Op-Amp offers a wide input common-mode voltage range and output voltage swing. It also takes the minimum operating supply voltage down to 2.1V and the maximum recommended supply voltage to 5.5V. Moreover, SGM8521 provides 150 kHz bandwidth at a low current consumption of 4.7 µA.
The module provides a standard, right-angled, 3-pin male-header interface connection:
- GND: 0V (Ground connection)
- VCC: 3.3V to 5.5V (5mA current consumption)
- OUT: 0V to 1V ( 0 to 10 UV Index)
Application:
- Uv tester
- UV watches
- outdoor sports equipment
- mobile phone, etc
Reviews (0)
Shipping & Delivery
Related products
1 CHANNEL 12V RELAY
- 1-Channel relay interface board
- Operating voltage: 12V DC
- Provide high current relay of 15A
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances
- LED status indicates relay ON/OFF state.
- High current relay of 10A @250 V AC/10A@ 30V DC
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 43*17*17mm
- Weight: 150gm
16 CHANNEL 12V RELAY
- 16 channel 12V relay board
- Operating voltage: 12V
- Supply current: 0.2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- LED status indicates relay ON/OFF state.
- The 10-16 road can be any full-on/off or any road
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Normally closed or normally open with each port
- Strong anti-jamming ability and stable performance
- The on-board power supply module doesn’t need any external power
- Dimension: 180*90*20mm
- Weight: 100gm
16 CHANNEL 5V RELAY
- 16 channel 5V relay board
- Operating voltage: 5V
- Supply current: 500mA
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- Low state voltage: 0V to 0.5V (relay is ON)
- High state voltage: 3.7V to 5V(relay is OFF)
- Single-chip design with reliable performance
- Strong anti-interferences
- Strong anti-jamming ability and stable performance
- The on-board power supply module doesn’t need any external power
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Dimension: 180*90*20mm
- Weight: 100gm
4*3 MATRIX KEYPAD
- Operating voltage: 12V DC
- The maximum voltage across each button: 24v
- The maximum current across each button: 3mA
- Ultra-thin design
- Adhesive backing provides easy integration
- Easy communication with any microcontroller
- Flexible
- Only 7 microcontroller pins required to access 12 keys
- High price-performance ratio
- Allows microcontroller to scan 8 output pins to check which 16 button
- Long life
- Maximum operating temperature: 0 degrees to 50 degrees Celsius
- Dimension: 70*77*1mm
- Weight: 7.5gm
LDR Module
- Operating Voltage:3V to 5V DC
- Operating Current: 15milli amps
- LED indicating output and power
- LM393 comparator chip
- Can detect ambient brightness and light intensity.
- Output Type :Â - Digital switching outputs (0 and 1) -D0
- Output Digital: 0V to 5V, Adjustable trigger level from preset
- Power indicator (red) and the digital switch output indicator (green)
- It can detect ambient brightness and light intensity.
- Adjustable sensitivity (via blue digital potentiometer adjustment).
- Output Digital – 0V to 5V, Adjustable trigger level from preset.
- Fixed bolt hole for easy installation
- PCB size: 3cm * 1.6cm
TEMT6000 Ambient Light Sensor
- Adapted to human eye responsivity
- Wide-angle of half sensitivity ϕ = ± 60°
- SMD style package on PCB technology
- Suitable for IR reflow soldering
- Lead-free component
- Package type: surface mount
- High photosensitivity
- Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC
- Dimensions: 4 x 2 x 1.05mm
Reviews
There are no reviews yet.