I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-11%
BH1750
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
DHT11 MODULE
Original price was: ₹250.00.₹150.00Current price is: ₹150.00. inc. GST
CJMCU Guva S12SD Sunlight Ultraviolet UV Ray Intensity
Original price was: ₹650.00.₹580.00Current price is: ₹580.00. inc. GST
- Power supply voltage of 2.5 V ~ 5 V
- Low power consumption
- Wide detection range: 240 nm to 370 nm
- Wide Angle: 130 degrees
- Schottky type photosensitive diode
- Good linear response
- High sensitivity
- Low power consumption
- Power supply voltage of 2.5 V ~ 5 V
- Working current is microamps.
- High sensitivity
- High stability
- Wide detection range: 240 nm to 370 nm
- Wide Angle: 130 degrees
- Schottky type photosensitive diode
- Dimension: 11 mm x 27 mm
Description
The GUVA-S12SD UV Sensor chip is a microcontroller-compatible module used for detecting the intensity of UV radiation in sunlight. These are widely used in any application where we want to monitor the amount of UV light and is simple to connect to any microcontroller through one ADC channel.
This module operates with a typical UV detection wavelength of 200 – 370nm, then outputs a calibrated analogue voltage that varies with the UV light intensity. The UV Sensor module is based on the renowned sensor GUVA-S12SD. This is a Gallium Nitride material based Schottky-type photodiode, designed for photovoltaic mode operation. The other main component is an Op-Amp IC SGM8521 which is a rail-to-rail input and output voltage feedback amplifier offering low cost. Thus Op-Amp offers a wide input common-mode voltage range and output voltage swing. It also takes the minimum operating supply voltage down to 2.1V and the maximum recommended supply voltage to 5.5V. Moreover, SGM8521 provides 150 kHz bandwidth at a low current consumption of 4.7 µA.
The module provides a standard, right-angled, 3-pin male-header interface connection:
- GND: 0V (Ground connection)
- VCC: 3.3V to 5.5V (5mA current consumption)
- OUT: 0V to 1V ( 0 to 10 UV Index)
Application:
- Uv tester
- UV watches
- outdoor sports equipment
- mobile phone, etc
Reviews (0)
Shipping & Delivery
Related products
1 CHANNEL 5V RELAY
- 1 channel relay board
- Operating voltage: 5V
- Maximum current: 2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- configured as SINGLE POLE DOUBLE THROW( SPDT)
- LED status indicates relay ON/OFF state.
- Standard TTL level logic controlled
- One normally closed and one normally opened contact
- Compatible with any 5V microcontroller
- Dimension: 43*17*17mm
- Weight: 150gm
4*3 MATRIX KEYPAD
- Operating voltage: 12V DC
- The maximum voltage across each button: 24v
- The maximum current across each button: 3mA
- Ultra-thin design
- Adhesive backing provides easy integration
- Easy communication with any microcontroller
- Flexible
- Only 7 microcontroller pins required to access 12 keys
- High price-performance ratio
- Allows microcontroller to scan 8 output pins to check which 16 button
- Long life
- Maximum operating temperature: 0 degrees to 50 degrees Celsius
- Dimension: 70*77*1mm
- Weight: 7.5gm
DC-DC BOOST MODULE 0.9V-5V/5V 600MA USB MOBILE Power Supply Module
- Ultra-compact PFM chip
- Module properties: nonisolated step-up module
- Input voltage: 1v-5v
- Output voltage: 5.1v-5.2V
- Output current: rated 1A-1.5A
- Efficiency: 96%
- Output ripple: 30mv for 20M bandwidth
- Switching frequency: 500khz
- Voltage indication for led lights with load( for less than 2.7v led indicator off)
- Operating temperature:-40 degrees to 85 degrees Celsius
- Full load temperature rise: 30 degrees Celsius
- Quiescent current: 130ua
- Load regulation: +/-1%
- Voltage regulation: +/-0.5%
- Dynamic response speed: 5% 200Us
- Short circuit protection
- Reverse polarity protection
- Dimension: 2.5*1.8*1.8gm
- Weight: 400gm
LDR SENSOR 5mm
MOQ: 2 nosÂ
- Â No. of Pins: 2
- Â Type of Mounting: PCB Through Hole
- Â Maximum Operating Temperature: +800C (Approx.)
- Â Dark resistance:1-20M ohm
- Good reliability
- High sensitivity
- Fast response
- Good spectrum characteristic
- Size: 5mm (50-paise size)
- .Coated with epoxy
- Miniature open frame package.
- Proxy coated.
- Moisture resistant.
- Spectral response is similar to the human eye.
PH Tester Soil Water Moisture Light Test Meter Sensor
- Three different soil test meters in one device; Measures moisture, pH/Acidity, and light.
- Detector shape: Needle ( 1pc Copper needle, 1pc Silver needle)
- Needle length: approx. 210mm/8.26'
- Moist value (1-10RH): 1-3(Red): need water, 4-7(Green): favorable moisture, 8-10(Blue): too wet
- pH value (8-3.5): Neutral solution : =7, Acid reaction : <7, Alkaline reaction : >7
- Light value (0-2000 Lux)
- Higher values mean the greater the intensity of the light
- Help you to determine if the plant getting adequate light
- Total Length:250 mm
- Probe Length:170 mm
- Probe Diameter:5 mm
- Material: Body: Plastic
- Probe: Stainless Steel & Aluminium
- 100% Accuracy; Easy to read moisture, pH, and light levels;
- No battery is required, simple and convenient to use.
- Working temperature: 5 degrees -50 degrees C
- Dimension: 285*50*30mm
- Weight: approx. 57g
Reviews
There are no reviews yet.