I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-11%
BH1750
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
DHT11 MODULE
Original price was: ₹250.00.₹150.00Current price is: ₹150.00. inc. GST
CJMCU Guva S12SD Sunlight Ultraviolet UV Ray Intensity
Original price was: ₹650.00.₹580.00Current price is: ₹580.00. inc. GST
- Power supply voltage of 2.5 V ~ 5 V
- Low power consumption
- Wide detection range: 240 nm to 370 nm
- Wide Angle: 130 degrees
- Schottky type photosensitive diode
- Good linear response
- High sensitivity
- Low power consumption
- Power supply voltage of 2.5 V ~ 5 V
- Working current is microamps.
- High sensitivity
- High stability
- Wide detection range: 240 nm to 370 nm
- Wide Angle: 130 degrees
- Schottky type photosensitive diode
- Dimension: 11 mm x 27 mm
Description
The GUVA-S12SD UV Sensor chip is a microcontroller-compatible module used for detecting the intensity of UV radiation in sunlight. These are widely used in any application where we want to monitor the amount of UV light and is simple to connect to any microcontroller through one ADC channel.
This module operates with a typical UV detection wavelength of 200 – 370nm, then outputs a calibrated analogue voltage that varies with the UV light intensity. The UV Sensor module is based on the renowned sensor GUVA-S12SD. This is a Gallium Nitride material based Schottky-type photodiode, designed for photovoltaic mode operation. The other main component is an Op-Amp IC SGM8521 which is a rail-to-rail input and output voltage feedback amplifier offering low cost. Thus Op-Amp offers a wide input common-mode voltage range and output voltage swing. It also takes the minimum operating supply voltage down to 2.1V and the maximum recommended supply voltage to 5.5V. Moreover, SGM8521 provides 150 kHz bandwidth at a low current consumption of 4.7 µA.
The module provides a standard, right-angled, 3-pin male-header interface connection:
- GND: 0V (Ground connection)
- VCC: 3.3V to 5.5V (5mA current consumption)
- OUT: 0V to 1V ( 0 to 10 UV Index)
Application:
- Uv tester
- UV watches
- outdoor sports equipment
- mobile phone, etc
Reviews (0)
Shipping & Delivery
Related products
4 CHANNEL 12V RELAY
- 4-Channel relay interface board
- Relay input voltage: 12V DC
- Relay output: 5A/250V AC
- Signal input:5V DC from the microcontroller
- High current relay of 10A @250 V AC/10A@ 30V DC
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances such as DC motors, solenoid valves, lamps, etc.
- LED status indicates relay ON/OFF state.
- Power battery terminal for relay output and aux power connection
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- Relay can directly control all equipment’s and loads
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 165*65*1mm
- Weight: 7gm
8 CHANNEL 5V RELAY
- Relay operating voltage: 5V
- 8 channel
- High impedance controller pin
- One normally closed contact and one normally opened
- Useful for appliances control
- Power supply indicator and control indicator lamp
- Pull-down circuit to avoid malfunction
- Can control both DC and AC to 220v AC load
- Works with both 3.3 V and 5 V logic with the less current drive
- 3 terminals per SPDT relay
- Standard interface can be directly controlled by a microcontroller like Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic
- Dimension: 7*6.4*1 inch
TEMT6000 Ambient Light Sensor
- Adapted to human eye responsivity
- Wide-angle of half sensitivity ϕ = ± 60°
- SMD style package on PCB technology
- Suitable for IR reflow soldering
- Lead-free component
- Package type: surface mount
- High photosensitivity
- Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC
- Dimensions: 4 x 2 x 1.05mm
Reviews
There are no reviews yet.