I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-11%
BH1750
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
DHT11 MODULE
Original price was: ₹250.00.₹150.00Current price is: ₹150.00. inc. GST
CJMCU Guva S12SD Sunlight Ultraviolet UV Ray Intensity
Original price was: ₹650.00.₹580.00Current price is: ₹580.00. inc. GST
- Power supply voltage of 2.5 V ~ 5 V
- Low power consumption
- Wide detection range: 240 nm to 370 nm
- Wide Angle: 130 degrees
- Schottky type photosensitive diode
- Good linear response
- High sensitivity
- Low power consumption
- Power supply voltage of 2.5 V ~ 5 V
- Working current is microamps.
- High sensitivity
- High stability
- Wide detection range: 240 nm to 370 nm
- Wide Angle: 130 degrees
- Schottky type photosensitive diode
- Dimension: 11 mm x 27 mm
Description
The GUVA-S12SD UV Sensor chip is a microcontroller-compatible module used for detecting the intensity of UV radiation in sunlight. These are widely used in any application where we want to monitor the amount of UV light and is simple to connect to any microcontroller through one ADC channel.
This module operates with a typical UV detection wavelength of 200 – 370nm, then outputs a calibrated analogue voltage that varies with the UV light intensity. The UV Sensor module is based on the renowned sensor GUVA-S12SD. This is a Gallium Nitride material based Schottky-type photodiode, designed for photovoltaic mode operation. The other main component is an Op-Amp IC SGM8521 which is a rail-to-rail input and output voltage feedback amplifier offering low cost. Thus Op-Amp offers a wide input common-mode voltage range and output voltage swing. It also takes the minimum operating supply voltage down to 2.1V and the maximum recommended supply voltage to 5.5V. Moreover, SGM8521 provides 150 kHz bandwidth at a low current consumption of 4.7 µA.
The module provides a standard, right-angled, 3-pin male-header interface connection:
- GND: 0V (Ground connection)
- VCC: 3.3V to 5.5V (5mA current consumption)
- OUT: 0V to 1V ( 0 to 10 UV Index)
Application:
- Uv tester
- UV watches
- outdoor sports equipment
- mobile phone, etc
Reviews (0)
Shipping & Delivery
Related products
16 CHANNEL 12V RELAY
- 16 channel 12V relay board
- Operating voltage: 12V
- Supply current: 0.2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- LED status indicates relay ON/OFF state.
- The 10-16 road can be any full-on/off or any road
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Normally closed or normally open with each port
- Strong anti-jamming ability and stable performance
- The on-board power supply module doesn’t need any external power
- Dimension: 180*90*20mm
- Weight: 100gm
20mm LDR
- Diameter: 25mm
- Â No. of Pins: 2
- Â Type of Mounting: PCB Through Hole
- Â Maximum Operating Temperature: +800C (Approx.)
- Â Dark resistance:1-20M ohm
- Good reliability
- High sensitivity
- Fast response
- Good spectrum characteristic
- Size: 20mm (50-paise size)
- .Coated with epoxy
- Miniature open frame package.
- Proxy coated.
- Moisture resistant.
- Spectral response is similar to the human eye.
CURRENT SENSOR ACS712 30AMPS
- Current sensor chip: ACS712ELC-30A
- Supply voltage: 4.5V to 5.5V DC
- Current range: -30A to 30A
- Sensitivity: 66 millivolt/ampere
- Low noise analogue signal path
- Output rise time: 5 micro sec
- Extremely stable output offset voltage
- Zero magnetic hysteresis
- Factory trimmed for accuracy
- Easy to interface with a microcontroller, since it outputs an analogue voltage
- Onboard power indicator
- Dimension: 7*5*5cm
- Weight: 400gm
DC-DC BOOST MODULE 0.9V-5V/5V 600MA USB MOBILE Power Supply Module
- Ultra-compact PFM chip
- Module properties: nonisolated step-up module
- Input voltage: 1v-5v
- Output voltage: 5.1v-5.2V
- Output current: rated 1A-1.5A
- Efficiency: 96%
- Output ripple: 30mv for 20M bandwidth
- Switching frequency: 500khz
- Voltage indication for led lights with load( for less than 2.7v led indicator off)
- Operating temperature:-40 degrees to 85 degrees Celsius
- Full load temperature rise: 30 degrees Celsius
- Quiescent current: 130ua
- Load regulation: +/-1%
- Voltage regulation: +/-0.5%
- Dynamic response speed: 5% 200Us
- Short circuit protection
- Reverse polarity protection
- Dimension: 2.5*1.8*1.8gm
- Weight: 400gm
LDR Module
- Operating Voltage:3V to 5V DC
- Operating Current: 15milli amps
- LED indicating output and power
- LM393 comparator chip
- Can detect ambient brightness and light intensity.
- Output Type :Â - Digital switching outputs (0 and 1) -D0
- Output Digital: 0V to 5V, Adjustable trigger level from preset
- Power indicator (red) and the digital switch output indicator (green)
- It can detect ambient brightness and light intensity.
- Adjustable sensitivity (via blue digital potentiometer adjustment).
- Output Digital – 0V to 5V, Adjustable trigger level from preset.
- Fixed bolt hole for easy installation
- PCB size: 3cm * 1.6cm
PH Tester Soil Water Moisture Light Test Meter Sensor
- Three different soil test meters in one device; Measures moisture, pH/Acidity, and light.
- Detector shape: Needle ( 1pc Copper needle, 1pc Silver needle)
- Needle length: approx. 210mm/8.26'
- Moist value (1-10RH): 1-3(Red): need water, 4-7(Green): favorable moisture, 8-10(Blue): too wet
- pH value (8-3.5): Neutral solution : =7, Acid reaction : <7, Alkaline reaction : >7
- Light value (0-2000 Lux)
- Higher values mean the greater the intensity of the light
- Help you to determine if the plant getting adequate light
- Total Length:250 mm
- Probe Length:170 mm
- Probe Diameter:5 mm
- Material: Body: Plastic
- Probe: Stainless Steel & Aluminium
- 100% Accuracy; Easy to read moisture, pH, and light levels;
- No battery is required, simple and convenient to use.
- Working temperature: 5 degrees -50 degrees C
- Dimension: 285*50*30mm
- Weight: approx. 57g
Reviews
There are no reviews yet.