I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-9%
Flex Sensor 4.5”
Original price was: ₹1,100.00.₹1,000.00Current price is: ₹1,000.00. inc. GST
Force Sensor 14.7MM
Original price was: ₹700.00.₹600.00Current price is: ₹600.00. inc. GST
Force Sensor 5.08mm
Original price was: ₹550.00.₹500.00Current price is: ₹500.00. inc. GST
- Two pins extend from the bottom of the sensor with 0.1″ pitch making it bread friendly.
- Device Rise Time: <3 microseconds
- Easily customizable to a wide range of sizes
- Actuation Force: 0.1 Newtons
- Cost-effective
- Ultra-thin; 0.45 mm
- Robust; up to 10 million actuation
- Force Sensitivity Range: 0.1 – 10.02 Newtons
- Simple and easy to Integrate.
- Non-Actuated Resistance: 10M W
- Temp Operating Range: 30 – +70 ºC
- 16MHz Clock Speed
- 32 KB Flash Memory
Description
This is a small force sensitive resistor with a 0.16″ (4 mm) diameter active sensing area. The resistance of this force sensor changes depending on how much pressure is applied to the sensing area which can be measured using any microcontroller. Thus the Force sensor responds to the applied force and converts the value to a measurable quantity. The stronger the force, the lower the resistance will be. Under the condition, when no pressure is applied to the Force sensor, its resistance will be larger than 1MΩ. When the full pressure is applied the resistance will be 2.5kΩ.
Force Sensing Resistors (FSR) consists of a polymer thick film (PTF) device in which the resistance decreases with an increase in the force applied to the active surface. Even though the force sensor is accurate for sensing pressure, these are not suitable for precision measurements. This sensor contains two pins that extend from the bottom of the sensor with a 0.1″ pitch making it breadboard friendly and making installation quite easier. It should be considered that the base of the sensor is sensitive to bending and may get damaged. Hence care should be taken that you bend only the sensing area.
Applications:
- Testing and Measurement Equipment
- Embedded Electronics
- OEM Development Kit
- Consumer Electronics
- Multimeter
Reviews (0)
Shipping & Delivery
Related products
50Kg Pressure Micro Scale Weighing Sensor
- Capacity : 50.kg
- Output Sensitivity (mv/v): 1.0±0.1.
- Nonlinearity (%FS): 0.03.
- Repeatability (%FS): 0.03.
- Input Resistance: 1000. Ω
- Insulation Resistance : ≥5000.MΩ
- Alloy Steel wired weighing load cell
- High Accuracy
- Simple Structure & Easy Installation.
- Internal 1000 Ω half-bridge strain gauge load cell, the range is 50kg, half-bridge structure
- You can use multiple load sensors simultaneously to increase the capacity range, Parallel use to add additional capacity.
DS18B20 MODULE
- Resolution: 9bits to 12bits (Selectable)
- Supply Voltage (V): 3 to 5.5
- Temperature Range(°C): -55 to +125
- Measuring Accuracy(°C): ±0.5
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into the chip
- Multiple sensors can share one pin
- Maximum conversion time and response: 750 ms
- Multidrop capability simplifies distributed temperature sensing applications
- Requires no external components
- Digital signal output
- 18B20 Temperature Sensor Chip
- Send data via a pin
- User-definable nonvolatile (NV) alarm settings
- Dimension: 19*15*6cm
- Weight: 9gm
MQ2 Sensor
- Operating Voltage: +5V
- Can be used to Measure or detect LPG, Alcohol, Propane, Hydrogen, CO, and even methane
- Analogue output voltage: 0V to 5V
- Digital Output Voltage: 0V or 5V (TTL Logic)
- Preheat duration 20 seconds
- Can be used as a digital or analogue sensor
- Load resistance: 20 KΩ
- Heater resistance: 33Ω ± 5%
- Heating consumption: <800mw
- Sensing Resistance: 10 KΩ – 60 KΩ
- Detection range: 200 – 10000ppm
- Preheat Time: Over 24 hour
- High sensitivity to LPG, Propane, and Hydrogen
- The Sensitivity of a Digital pin can be varied using the potentiometer
MQ4 Sensor
- Power requirements: VCC - 5V±0.1
- DO output: TTL digital 0 and 1 (0.1 and 5V)
- AO output: 0.1-0 .3 V (relative to pollution), the maximum concentration of a voltage of about 4V
- Detection Gas: Natural gas/Methane
- Detection Concentration: 200-10000ppm (Natural gas / Methane)
- Interface: 1 TTL compatible input (HSW), 1 TTL compatible output (ALR)
- Heater consumption: less than 750mw
- Operating temperature: 14 to 122 °F (-10 to 50°C)
- Related humidity less than 95%Rh
- Load resistance: 20KΩ
- Sensing Resistance: 10KΩ- 60KΩ (1000ppm CH4)
- Preheat time: Over 24 hour
- Standard Encapsulation Bakelite, Metal cap
MQ8 GAS SENSOR
- Operating Voltage: 3.3 – 5V.
- Type: Analog Sensor.
- Detection range: 100~1000ppm(H2 gas)
- Heating voltage (high): 5V ± 0.1
- Heating voltage (low): 1.4V ± 0.1
- Load resistance: Adjustable
- Heating resistance: 31Ω ± 5%
- Heating consumption: less than 800mW
- Using temperature: -20°C-50°C
- Storage temperature: -20°C-50°C
- Relative humidity: 55%+-5%RH
- High Sensitivity for Hydrogen
- Small sensitivity to alcohol, LPG, cooking fumes
PIEZO Vibration Sensor
- Flexible PVDF Piezo Polymer Film
- Flex, Touch, Vibration and Shock measurements
- Voltage Sensitivity (open-circuit, baseline): 1.1 V/g.
- Charge Sensitivity (baseline): 260 pC/g.
- Upper Limiting Frequency (+3 dB): 42 Hz.
- Resonance Frequency: 75 Hz.
- Voltage Sensitivity (open-circuit, at resonance): 6 V/g.
- Wide dynamic range：001Hz~1000MHz
- Laminated for higher voltage output
- Breadboard friendly leads.
- Standard grove socket
- Adjustable sensitivity
- Withstands High Impact
- Operating Temperature: 0ºC to 85ºC
- Storage Temperature: -40ºC to 85 ºC
- Dimensions: 6.9 x 3.9 x 0.8 cm
- Weight: 10 Grams
Reviews
There are no reviews yet.