I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
ISD1760 MODULE (75 sec)
₹549.00 Original price was: ₹549.00.₹499.00Current price is: ₹499.00. inc. GST
- On-board ISD1760 chip
- Operating voltage: 5v
- 75 sec of audio playback
- Onboard microphone for direct recording
- Frequency: 6KHz or 8KHz
- Recording time: 6K/75 sec, 8K/60 sec
- Output all pin for chip control
- Easy interface with microcontrollers using 2.54mm spaced male pin headers
- High-quality natural voice reduction
- LED status indication
- Long recording time and multiple messages
- Simple operation and better voice quality
- Control not only by buttons but also by SPI from a microcontroller
- Recording, erase, play, FT, fast forward, reset volume buttons
- Dimension: 49*41.5mm
- Weight: 22gm
Â
Out of stock
ISD1760 is a playback module consisting of an onboard microphone and a voice recording IC with 75 sec of audio playback. This module is is compatible with all ISD1760 series families that can be applied to all series chips, with simple and full functional characteristics. ISD1760 Module is defined as highly integrated and high-performance chips with multi-segment recording at an adjustable sampling rate from 4k to 12k at a varying power supply of 2.4V to 5.5V. The LED indication is provided every few seconds to alert the user for new recordings. Apart from it, there are 4 modes of sound to prompt user operating results.ie start reading, stop reading, erase, and erase all next to one, and so on.
Flash chip is used to store data without any compression. In SPI mode, the user function more on-chip address and power are less consumed by automatically entering to power-down mode. Analog channel configuration register used for reading and writing memory addresses on the playback. Moreover, the recording data is stored without any compression in the FLASH chip. Hence offers better sound quality and power storage.
This playback module chip consists of two independent audio signal input channels, microphone input, and analogue signal inputs. In the independent key mode, as soon as the operation is completed, a functional chip automatically enters the power-down mode to reduce power consumption. And also the 2.54mm spaced male pin headers in the module allow easy interfacing with the microcontroller.

Related products
16 CHANNEL 12V RELAY
- 16 channel 12V relay board
- Operating voltage: 12V
- Supply current: 0.2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- LED status indicates relay ON/OFF state.
- The 10-16 road can be any full-on/off or any road
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Normally closed or normally open with each port
- Strong anti-jamming ability and stable performance
- The on-board power supply module doesn’t need any external power
- Dimension: 180*90*20mm
- Weight: 100gm
3.3V/5V MB102 Breadboard Power Supply Module
- Input voltage: 6.5V to 12V
- Output voltage: 3.3V to 5V
- Output current: 700Ma
- Apply to MB102 breadboard
- Sorting jumpers used to switch voltage between 3.3V and 5V
- Onboard LED indicator to show the presence of power
- Short circuit protection
- Fits securely on standard 400 and 830 points on the breadboard
- Dimensions: 53*32*23mm
- Weight: 10gm
4*3 MATRIX KEYPAD
- Operating voltage: 12V DC
- The maximum voltage across each button: 24v
- The maximum current across each button: 3mA
- Ultra-thin design
- Adhesive backing provides easy integration
- Easy communication with any microcontroller
- Flexible
- Only 7 microcontroller pins required to access 12 keys
- High price-performance ratio
- Allows microcontroller to scan 8 output pins to check which 16 button
- Long life
- Maximum operating temperature: 0 degrees to 50 degrees Celsius
- Dimension: 70*77*1mm
- Weight: 7.5gm
CURRENT SENSOR ACS712 30AMPS
- Current sensor chip: ACS712ELC-30A
- Supply voltage: 4.5V to 5.5V DC
- Current range: -30A to 30A
- Sensitivity: 66 millivolt/ampere
- Low noise analogue signal path
- Output rise time: 5 micro sec
- Extremely stable output offset voltage
- Zero magnetic hysteresis
- Factory trimmed for accuracy
- Easy to interface with a microcontroller, since it outputs an analogue voltage
- Onboard power indicator
- Dimension: 7*5*5cm
- Weight: 400gm
DC-DC BOOST MODULE 0.9V-5V/5V 600MA USB MOBILE Power Supply Module
- Ultra-compact PFM chip
- Module properties: nonisolated step-up module
- Input voltage: 1v-5v
- Output voltage: 5.1v-5.2V
- Output current: rated 1A-1.5A
- Efficiency: 96%
- Output ripple: 30mv for 20M bandwidth
- Switching frequency: 500khz
- Voltage indication for led lights with load( for less than 2.7v led indicator off)
- Operating temperature:-40 degrees to 85 degrees Celsius
- Full load temperature rise: 30 degrees Celsius
- Quiescent current: 130ua
- Load regulation: +/-1%
- Voltage regulation: +/-0.5%
- Dynamic response speed: 5% 200Us
- Short circuit protection
- Reverse polarity protection
- Dimension: 2.5*1.8*1.8gm
- Weight: 400gm
Fingerprint Scanner TTL GT511C3 – 3.3V to 6V
- Model: GT-511C3
- Operating Voltage(VDC): 3 to 6
- CPU: ARM Cortex M3 Core (Holtek HT 32F2755)
- Sensors: Optical
- Image Size: 202 x 258 Pixel
- Resolution: 450 DPi
- Effective Scanning Area(mm): 20 x 16
- False Acceptance Rate (FAR): 0.001%
- False Rejection Rate(FRR): < 0.1%
- Operating Temperature : -20°C ~ +60°C
- Default Baud Rate: 9600bps
- High-Speed, High-Accuracy Fingerprint Identification using the Smack Finger 3.0 Algorithm
- Read and Write Fingerprint Templates and Databases
- Simple UART protocol (Default 9600 baud)
- Capable of 1:1 Verification and 1:N Identification
- High-accuracy & high-speed fingerprint identification technology.
- Works well with dry, moist, or rough fingerprints.
- 200 fingerprints storage.
- Easy one-touch enrolment.
- Dimensions(mm): 37 x 17 x 9.5
- Weight: 6gm
R305 Optical Fingerprint Reader Sensor Module
- Power DC: 3.6V-6.0V
- Interface : UART (TTL logical level)/ USB 1.1)
- Working current: 100mA
- Peak Current: 150mA
- Matching mode (1: 1)
- Search method (1: N)
- Connecting cable length (cm): 8.5
- Baud rate (9600*N)bps, N=1-12 (default N=6 57600bps)
- Character file size: 256 bytes
- Image acquiring time: <0.5s
- Template size: 512 bytes
- Storage capacity: 256
- FAR : <0.001%; FRR: <0.1%
- Average searching time: < 0.8s (1:880)
- Working environment: Temp: -10degree to +40degree C
- Storage environment Temp: -40degree to +85degree C
- RH: 40%-85% RH: <85%
- Integrated image collecting and algorithm chip together, ALL-in-One.
- Low power consumption, low cost, small size, excellent performance.
- Professional optical technology, precise module manufacturing techniques.
- Good image processing capabilities can successfully capture an image up to a resolution of 500 dpi.
- Window dimension : 18mm*22mm
- Optical module: 49 x 20 x 21.20 mm
- Touch Sensors: 18 x 14.5 mm.
- Weight: 16gm
Sonar Range Finder -High Performance Ultrasonic Sensor Module
- Low-cost ultrasonic rangefinder
- Size less than 1 cubic inch with easy mounting
- Resolution of 1mm
- 100mS measurement cycle
- The free run operation uses a 2Hz filter, with 100mS measurement and output cycle
- Operating temperature range from -15°C to +65°C
- Operating voltage from 2.5V to 5.5V
- Nominal current draw of 2.5mA at 3.3V, and 3.1mA at 5V

Reviews
There are no reviews yet.