I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-6%
650nm RED LASER DOT DIODE MODULE
Original price was: ₹200.00.₹175.00Current price is: ₹175.00. inc. GST
2 Wires 0.28 inch Digital Voltmeter DC 0-100V Red Light LED Panel Voltage Meter
Original price was: ₹200.00.₹150.00Current price is: ₹150.00. inc. GST
L293D MOTOR DRIVER
Original price was: ₹160.00.₹150.00Current price is: ₹150.00. inc. GST
- Can be used to run two dc motors with the same IC
- Speed and direction control is possible
- Supply voltage: 4.5 V to 7V
- Motor voltage: 4.5 v to 36v
- Maximum peak motor current: 1.2 A
- Maximum continuous motor current: 600 milli ampere
- Screw terminal connectors for easy connection
- Transition time: 300 ns (at 5v and 24v)
- High noise immunity inputs
- Automatic thermal shutdown
- Available in 16 pin DIP, TSSOP, SOIC package
- Dimension: 48*34*14mm
- Weight: 15gm
Description
A motor driver designed as an integrated circuit chip basically used to control motors in autonomous robots. Motor drivers function as an interface between Arduino and the motors.L293 D Motor Driver is one of the most commonly used motor driver IC’s in the electronics system. L293D motor driver defined as a 16 pin, monolithic integrated, high power driver for driving DC motor. The L293D designed as a dual H bridge motor driver capable of driving a pair of DC motors or a single stepper motor. It uses the popular L293 motor driver IC. Hence, It can drive 4 DC motors on and off, or drive 2 DC motors with direction and speed control independently. The H-bridge is the most basic circuit for controlling a motor with a low current rating. It can drive up to two motors independently, making it perfect for developing two-wheel robot platforms.
L293D is the optimum choice for motors with an operating voltage less than 36V and an operational current less than 600mA that will be controlled by digital circuits like as Op-Amps, 555 timers, digital gates, or even Micron rollers such as Arduino, PIC, ARM, and others. The driver considerably simplifies and improves the simplicity with which microcontrollers may operate motors, relays, and other devices. It has a total DC current of up to 600mA and can drive motors up to 12V.
Reviews (0)
Shipping & Delivery
Related products
40A DC MOTOR SPEED REGULATOR PWM CONTROLLER 2000W
- Speed controller model: 40A PWM DC motor speed regulator
- Operating voltage: 10V TO 50V
- Peak current: 40A
- Control power: 0.01-2000W
- Quiescent current: 0.025A
- PWM regulation: 5-100%
- PWM frequency: 12KHz
- Operating temperature: -20 degree to 40 degree Celsius
- Stability in working
- High efficiency
- potentiometer used for speed adjustability
- Dimension: 9*5.1mm
- Weight: 95gm
48v 500W BM1418ZXF Motor Controller
- Rated Voltage: 48 Volt DC.
- Rated Power: 500W.
- Maximum Current: 30 Amps.
- Level Brake: low.
- Current limited: 30A±0.5A.
- Efficiency: ≥83%.
- Consumption: <1.5W.
- Turn The Voltage: 1-4.2V.
- Phase Angle: 120 degrees.
- Includes attachments for motor, accelerator, brake, battery, battery charging, brake light, power lock
5V-12V DC Brushless Motor Driver Board Controller
- Type: Voltage Regulator
- Drive voltage: DC 5-l2V
- Work current: ≤ 1.2A
- Speed range: from 0% to 100%
- Phase inversion Control
- Offers Voltage polarity protection and Overcurrent Protection
- Suitable for hard brushless motor, brushless motor drive and other miniature 3 / 4 wire brushless motor without hall
A4988 Stepper Motor
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Logic Voltage supply: 3.3 V to 5 V
- Compatible with 3V3 and 5V microcontrollers
- Our Board comes with 0.1 Ohm Sensor resistors
- Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
- The Correct current decay mode (fast decay or slow decay) is selected by chopping the control
- Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
- Short-to-ground and shorted-load protection
- 4-layer, 2 oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
A4988 STEPPER MOTOR DRIVE CONTROLLER BOARD
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor; Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
IRF520 MOSFET DRIVER MODULE SENSOR
- Operating Voltage: 3.3v & 5v
- Digital level port
- Output load voltage: 0-24v
- Output load current: <5A
- The heat sink is added for currently more than 1A
- Compatible with Arduino, MCU, ARM, Raspberry pi
- PWM dimming LED used to step-less dimming, variable-speed motor
- Output PWM can be adjusted by the original IFR520 MOS
- Arduino can drive up to 24V, such as led lights, dc motors, miniature pumps, solenoid valves etc.
- Dimension:34*30*18mm
- Size: 10gm
Leadshine DM542
- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Extremely cost-effective
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology
- TTL compatible and optically isolated input
- 15 selectable resolutions in decimal and binary, up to 25,600 steps/rev
- Suitable for 2-phase and 4-phase motors
- DIP switch current setting with 8 different values
- Support PUL/DIR and CW/CCW modes
- Short-voltage, over-voltage, over-current protection
Leadshine DMA860E Stepper Motor Driver
- Model: DMA860E.
- Control Mode: Step & Direction.
- Max Input Frequency: 200 kHz.
- Input Voltage Range: 18 - 80 VAC / 24 - 110 VDC.
- Suggested Power Supply Voltage Range: 36-90 VDC /24-60 VAC.
- Number of DIP Switch Resolution Configurations: 16.
- 16 selectable micro-step resolutions of 400-51,200 via DIP switches.
- 8 selectable output current settings of 2.4 – 7.2A via DIP switches.
- Logic Current Range: 7-16mA (10mA typical).
- Logic Voltage Range: 4-5 VDC for pulse active high (default), or 0-0.5V for pulse active low.
- Pulse enabled at: Rising edge.
- Idle Current Percentage: 50 %.
- Number of Digital Inputs: 3.
- Step Width: 2,500 ns.
- Minimal Direction Setup Time: 5,000 ns.
- Isolation Resistance: 500M Ohm..
- Ambient Temperature: 0-50°C.
- Humidity: 40–95% RH.
- Operating Temperature: 0-70°C.
- Vibration: 5.9 m/s2 Max.
- Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors.
- Step & direction (PUL/DIR) and CW/CCW (via internal jumper set) control. Step & direction by default Multi-Stepping for smooth motor movement.
- Opto Isolation for input control signals.
- Soft-start with no “jump” when powered on.
- Protections for over-voltage and over-current.
- Dimension: 5.94 X 3.82 X 2.24 Inches.
- Weight: 1.13 lbs.
Reviews
There are no reviews yet.