I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-17%
LM3915 Dot or Bar Display Driver IC
Original price was: ₹60.00.₹50.00Current price is: ₹50.00. inc. GST
TNY254PN Off-line Switcher IC
Original price was: ₹65.00.₹55.00Current price is: ₹55.00. inc. GST
LM4250 Programmable Operational Amplifier IC
Original price was: ₹60.00.₹50.00Current price is: ₹50.00. inc. GST
- Input Offset Voltage (max): 6mV
- Input Offset Current (max): 20nA
- Input Bias Current (max): 75nA
- Operating temperature (max): 700C
- Output Current (max): 0.1mA
- CMRR (min): 70dB
- Programmable Operational Amplifier
- ±1V to ±18V power supply operation
- 3 nA input offset current
- Standby power consumption as low as 500 nW
- No frequency compensation required
Description
LM4250 designed as a highly versatile monolithic operational amplifier. These IC comes with a single external programming resistor that determines the quiescent power dissipation, input offset and bias currents, slew rate, gain-bandwidth product, and input noise characteristics of the amplifier. These IC works perfectly with most CMOS, NMOS, and PMOS devices. Moreover, the LM4250 features short circuit protection, ESD barring, and low thermal dissipation.
A programmable operational amplifier defined as an industry standard, frequency compensated operational amplifier, whose gain controlled by external digital or analog signals. The LM4250C is nearly just like the LM4250 except that the LM4250C has its performance guaranteed over 0ËšC to +70ËšC temperature range rather than the −55ËšC to +125ËšC temperature range of the LM4250. Since the device is in effect a special op amp for every externally programmed set current, it’s possible to use one stock item for a spread of circuit functions during a system. The LM4250 has two special features in comparison with other monolithic operational amplifiers. First of all, its ability to externally set the bias current levels of the amplifiers. Secondly, the utilization of PNP transistors because the differential input pair.
These programmable op-amps are widely utilized in the experimental design phase, where final specification’s are yet to be determined and also range of adjustment of key parameter’s is vital . These IC also utilized in variable frequency active filters, current controlled oscillators, and modulators.
PIN DESCRIPTION:
- Pin 1: OFFSET NULL 1: Offset Null Pin 1
- Pin 2: INV-INPUT: Inverting Input Pin
- Pin 3: NON-INV-INPUT: Non Inverting Input Pin
- Pin 4: Â V-: Negative Power Supply
- Pin 5: Â OFFSET NULL 2: Offset Null Pin 2
- Pin 6: OUTPUT: Output Pin
- Pin 7: Â V+: Positive Power Supply
- Pin 8: QUS-CURRENT: Quiescent Current Set Pin/Quiescent State
Reviews (0)
Shipping & Delivery
Related products
25pcs Button Switch Kit
- Relative Humidity: 95%
- Rated Voltage: 12V
- Rated Current: 50 mA
- Contact resistance: 50M Ohm Max (initial)
- The insulation resistance: 100M Ohm minDC (250V)
- The compressive strength: AC250V (50/60Hz for 1 minute)
- Mechanical life: 100000 cycles
- The environment temperature: 25° ~ + 105°
- The operating strength: 180/250 (plus or minus 30gf)
- Dimension: 12 * 12 * 7.3 round convex type
- Total Buttons: 25pcs
- Colours: 5 (Black, Red, White, Blue, Yellow)
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
Dual Micro USB 3.7v to 5V 2A Power Bank DIY 18650 LiPo Charger
- 4-level LED lamp display power, not working state intelligent automatic shutdown;
- The built-in lithium battery protection IC, over-current, under-voltage protection;
- Dual USB output ports.
- Dimensions: 68 x 34 x 9 mm (LxWxH)
- Weight: 10 gm
- Input port: MicroUSB (Andro)
- Input requirements: 5V constant voltage power supply can do charge input power, the most matching charger for 5v1a above
- Output port: USB
- Output parameters: 5V1A/5V2A
- Requirements for rechargeable batteries:
- Compatible Batteries: 18650 batteries, cell phone batteries, flat-panel batteries, MP3 batteries, etc. 3.7v-4.2V polymer Lithium battery,
Solid State Relay Module DC To AC SSR-40DA 3-32VDC/24-380VAC 40A
- Control mode: DC-AC
- Input voltage: 3-32V DC.
- Output voltage: 24-380V AC.
- Output current: 40A.
- Working voltage: 250V.
- Material: plastic + metal.
- Loading current: 40A
- Control current: 3-25mA DC
- On voltage: ≤1.5V AC
- One-off Time: ≤10ms
- Off Leakage Current: ≤2mA
- Dielectrics voltage-resistance: 2500VAC
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
Reviews
There are no reviews yet.