I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
LoRa SX1278 433M 10KM Wireless Spread Spectrum Transmission Module Ra-02 SX1278 Socket IOT
₹800.00 Original price was: ₹800.00.₹750.00Current price is: ₹750.00. inc. GST
- Lora Spread Spectrum Modulation Technology +20dBm-100mW
- Constant RF power output when voltage changes
- High sensitivity: low to -148dBm
- Half-duplex SPI communication Programmable bit rates up to 300kbps
- Supports FSK, GFSK, MSK, GMSK, LoRa and OOK modulation modes
- 127dB RSSI dynamic range
- Automatic RF signal detection
- CAD model and ultra-high-speed AFC With CRC, up to 256 bytes of the packet engine
- Small volume dual-row stamp-hole patch package
- With shielding shell Spring antenna (Ra-01) external antenna (Ra-02)
- Wireless standard 433MHz Frequency range: 420 ~ 450MHz
- Interface: SPI GPIO
- Operating Voltage:1.8 ~ 3.7V, the typical value is 3.3V
- Current: Receiver:≦ 10.8mA (LnaBoost off, band 1) Transimit: ≦ 120mA (+ 20dBm)
- Sleep mode: 0.2μA
- Working temperature: -40 to + 85 ° C
- Storage temperature: Normal
Ra-02 SX1278 was designed as a wireless transmission module based on SEMTECH’s SX1278 wireless transceiver. It Utilizes the advantages of advanced LoRa spread spectrum technology, offering a communication distance of 10,000 meters. It provides a strong ability of anti-jamming and has the function of air wake-up Consumption. The SX1278 RF module is widely used for long-range spread spectrum communication. And can also resist Minimizing current consumption. The SX1278 offers a high sensitivity of -148 dBm with an influence output of +20 dBm. And an extended transmission distance and high reliability. At a similar time, compared with the normal modulation technology, LoRa â„¢ modulation technology has obvious advantages in anti-blocking and selection, Thus solving the matter that the normal design scheme. Which can’t consider the distance, interference and power consumption at an equivalent time.
It often covers thousands of people in the district environment, particularly suitable for meter reading, smart home, burglar alarm equipment. This product was designed based on the WIFI Kit 32 added SX1278 chip, i.e. LoRa remote modem, 433MHz frequency, about -148dBm high sensitivity, +20 dBm power output. And also offers high reliability, transmission distance (measured open area communication distance 2.6Km).

Related products
1 CHANNEL 12V RELAY
- 1-Channel relay interface board
- Operating voltage: 12V DC
- Provide high current relay of 15A
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances
- LED status indicates relay ON/OFF state.
- High current relay of 10A @250 V AC/10A@ 30V DC
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 43*17*17mm
- Weight: 150gm
16 CHANNEL 12V RELAY
- 16 channel 12V relay board
- Operating voltage: 12V
- Supply current: 0.2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- LED status indicates relay ON/OFF state.
- The 10-16 road can be any full-on/off or any road
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Normally closed or normally open with each port
- Strong anti-jamming ability and stable performance
- The on-board power supply module doesn’t need any external power
- Dimension: 180*90*20mm
- Weight: 100gm
2 CHANNEL 5V RELAY
- High current relay
- Two LED S to indicate relays ON/OFF status
- Low-level trigger expansion board
- Opto isolation circuitry
- Works with logic level signal 3.3V or 5V devices
- Can be used as normally open (NO) or normally closed (NC)
- Back EMF protection
- Ensures diode current protection
- AC control voltage: 250v @mx10A
- DC control voltage: 30V @max 10A
- Easy installation and fixing
4 CHANNEL 12V RELAY
- 4-Channel relay interface board
- Relay input voltage: 12V DC
- Relay output: 5A/250V AC
- Signal input:5V DC from the microcontroller
- High current relay of 10A @250 V AC/10A@ 30V DC
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances such as DC motors, solenoid valves, lamps, etc.
- LED status indicates relay ON/OFF state.
- Power battery terminal for relay output and aux power connection
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- Relay can directly control all equipment’s and loads
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 165*65*1mm
- Weight: 7gm
4*4 MATRIX KEYPAD
- The maximum current across each button: 3mA
- Easy communication with any microcontroller
- Ultra-thin design
- Adhesive backing provides easy integration
- High price-performance ratio
- Allows microcontroller to scan 8 output pins to check which 16 button
- Long life
- Maximum operating temperature: 0 degrees to 50 degrees Celsius
- Dimension: 70*77*1mm
- Weight: 7.5gm
8 CHANNEL 5V RELAY
- Relay operating voltage: 5V
- 8 channel
- High impedance controller pin
- One normally closed contact and one normally opened
- Useful for appliances control
- Power supply indicator and control indicator lamp
- Pull-down circuit to avoid malfunction
- Can control both DC and AC to 220v AC load
- Works with both 3.3 V and 5 V logic with the less current drive
- 3 terminals per SPDT relay
- Standard interface can be directly controlled by a microcontroller like Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic
- Dimension: 7*6.4*1 inch
ADXL345
- Supply voltage: 3.3V/5V
- Communication type: I2C/SPI
- Sensing range: +/-2G to +/-16G
- Sensitivity
- X: 28.6 LSB/G
- Y: 31.2 LSB/G
- Z:34.5 LSB/g
- On-board LDO voltage regulator
- Resolution: 13 bit
- Single tap/double-tap detection
- Embedded memory management system with FIFO
- 10000g shock survival
- Low power consumption as low as 23 µA in measurement mode and 0.1 µA in standby mode at VS = 2.5 V (typical)
- 3-axis MEMS accelerometer
- Ideal for noisy power environment
- Operating temperature: -40 degrees to 85 degrees Celsius
- Dimension: 28*14mm
Ethernet Shield
- Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
- Stackable Design, can directly be supported by Arduino official Ethernet Library.
- Supports up to four simultaneous socket connections
- Can be used to store files for serving over the network.
- Compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560).
- Can be accessed using the Mini SD TF library.
- The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted-pair Category 5 Ethernet cable.
- IEEE802.3af compliant
- Low output ripple and noise (100mVpp)
- Overload and short-circuit protection
- 1500V isolation (input to output)

Reviews
There are no reviews yet.