I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-17%
Vibrator Motor Button Type
Original price was: ₹80.00.₹70.00Current price is: ₹70.00. inc. GST
Attiny 5 Version 1
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
Micro DC 3-6V Submersible Pump Mini water pump
Original price was: ₹180.00.₹150.00Current price is: ₹150.00. inc. GST
- Operating Voltage : 3 ~ 6V
- Operating Current : 130 ~ 220mA
- Flow Rate : 80 ~ 120 L/H
- Maximum Lift : 40 ~ 110 mm
- Continuous Working Life: 500 hours
- Driving Mode: DC, Magnetic Driving
- Material: Engineering Plastic
- Outlet Outside Diameter: 7.5 mm
- Outlet Inside Diameter : 5 mm
Description
Micro DC 3-6V Submersible Pump Mini water pump is a low-cost and lightweight water pump. It is ideal for submersible pumps for a variety of liquid and air movement applications. As it provides enough pressure, used with nozzles to make the spray systems. This submersible mini water pump is highly resistant to heat. It operates at a voltage range of 3 ~ 6V power supply. It can take up to 120 liters per hour with a very low current consumption of 220mA. By simply connecting tube pipe to the motor outlet, submerge it in water and power it. It should be noted that the water level is always higher than the motor. In case of dry run, damage the motor due to heating and it will also produce noise.
Under the powered condition, the pump can suck water through the tube up to a maximum lift of 40-110cm. This pump runs very quietly with a sound level under 30db while pumping the liquid. Whereas it is also capable of pumping air, but pumping air is quite noisy compared with the liquid.
APPLICATIONS
- Small aquariums pumps
- Automatic plant watering systems
- Water priming pumps
- Music activated dancing water system, etc.
Reviews (0)
Shipping & Delivery
Related products
A2212 BRUSHLESS DC MOTOR 1000KV
- Motor KV: 1000
- Operating voltage: 7.2V to 12V (2 to 3Li-poly or 6to10 NiCad)
- LiPO Batteries: 2S-3S
- No-load Current: 10 V: 0.5 A.
- Current Capacity: 12A/60S
- Maximum current:13Amp for 60Sec
- Maximum Watts:150 Watt
- Efficiency Current: 4-10A
- Shaft Diameter: 3.17 mm
- Prop Adapter is quality tested
- Minimum ESC Specification: 18A (30A Suggested)
- Maximum operating temperature: + 80°C
- Complete speed control because of a three-phase connection.
- Long-life as there are no moving contact
- Thrust @ 3S with 1045 propeller: 800gms approx
- Thrust @ 3S with 0945 propellers: 475gms approx
- Thrust @ 3S with 0845 propellers: 475gms approx
- Motor Dimensions: 27.5 x 30mm
- Weight of motor:50-60 grams
A2212 BRUSHLESS DC MOTOR 1400KV
- Operating voltage: 7.2V to 12V
- LiPO Batteries: 2S-3S
- No-load Current: 10 V: 0.5 A.
- Current Capacity: 12A/60S
- Maximum current:13Amp for 60Sec
- Maximum Watts:150 Watt
- Efficiency Current: 4-10A
- Shaft Diameter: 3.17 mm
- Prop Adapter is quality tested
- Minimum ESC Specification: 18A (30A Suggested)
- Maximum operating temperature: + 80°C
- Complete speed control because of three-phase connection.
- Long-life as there are no moving contact
- Thrust @ 3S with 1045 propeller: 1000gms approx.
- Thrust @ 3S with 0945 propeller: 650gms approx.
- Thrust @ 3S with 0845 propeller: 550gms approx.
- Motor Dimensions: 27.5 x 30mm
- Weight of motor:50-60 grams
L298N MOTOR DRIVER
- Driver model: L298N 2A
- Driver chip: Double H bridge L298N
- Motor supply voltage: 46V(maximum)
- Motor supply current: 2A(maximum)
- Logic voltage: 5v
- Driver voltage: 5V-35V
- Driver current: 2A
- Logical current: 0-36mA
- Maximum power: 25W
- Current sensor for each motor
- LED indication for power status
- Heat sink for better performance
- Operating temperature: -25 degrees to 135 degrees Celsius
- Can be interfaced with simple manual switches, TTL logic gates, relays, etc.
- Dimension: 55*60*30mm
- Weight: 33gm
MARSPOWER MX1806 2280KV BLDC Motor
- VK: 2280
- Max thrust: 460g
- No of cells: 2-3S
- Framework: 12N14P
- Suitable Propeller: 5-6”
- Shaft: 2mm
- Minimum ESC Specification: 12A Suggested
- Durable with high quality
- The 0.2mm core to lower load temperature and increase efficiency
- Range of use for DJI F330 ZMR250 H250
- Do every single motor balancing test
- Japan NMB bearings provide low noise and long life
- 2mm spindle selection of Kawasaki, Japan, more efficient, less heat
- NdFeB magnets temperature selection
- MX1806 (positive thread motor)
- FPV all configurations life 7-8 minutes!
- Easy to loosen the nut bombing risk!
- Low centre of gravity design
- Long-endurance design
- Dimension: 26.7*23mm
- Weight: 18gm
NEMA 23 10.1 kg-cm
- Operating Voltage : 2.3 Volts
- Step Angle : 1.8°
- Holding Torque : 10.1 kg-cm
- Supply Current (A) : 2.8 Ampere/Phase
- Number of Leads : 4
- Inductance : 2.2 mH/Phase
- Resistance : 0.83 Ohm
- Rotor Inertia : 275 gm-cm2
- Weight (gm) : 650
- Detent Torque (kg-cm) : 0.36
- Frame Size (mm) : 57 x 57
- Inductance Accuracy : ±20%
- Resistance Accuracy : ±10%
- Shaft Diameter (mm) : 6.35
- Shaft Length (mm) : 20.6
- Step Angle Accuracy : ±5%
- Comparably more powerful than NEMA17 motors.
- The input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- It provides good starting, stopping, and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
Stepper Motor Nema 23 kg 7.2 kg Dual shaft
- Rated Voltage: 6.6 V
- Current/ phase: 1A
- Resistance/ phase: 6.6ohms
- Inductance/ phase: 8.2 mH
- Holding Torque: 7.2 kg-cm
- of Leads - 6
- Rotor Inertia - 275
- Weight: 0.65kg
- Detent Torque: 0.36 kg-cm
- Step Angle - 1.8°
- Step Angle Accuracy - ±5% (full step, no load)
- Resistance Accuracy - ±10%
- Inductance Accuracy - ±20%
- Frame Size (mm) - 57x57
- Shaft Length (mm) - 20.6
- Shaft Diameter (mm) - 6.35
- Comparably more powerful than NEMA17 motors.
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
Stepper Motor NEMA 34 122 kg-cm Hybrid Bipolar
- Rated Voltage:4.08V
- Phase: 2
- Current/ phase: 4A
- Holding Torque: 122 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 37mm
- Shaft Diameter: 13mm
- Long-lasting life
- Low cost for control achieved
- High torque at startup and low speeds
- Ruggedness
- Simplicity of construction
- Can operate in an open-loop control system
- Low maintenance
- Less likely to stall or slip
Stepper Motor NEMA 34 46 kg-cm Hybrid Bipolar
- Rated Voltage:4.2V
- Current/ phase: 4A
- Inductance/ phase: 7.3mH
- Resistance/ phase: 0.87ohms
- Holding Torque: 46 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 32mm
- Shaft Diameter: 12mm
- They are high torque stepper motors.
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing
Reviews
There are no reviews yet.