I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-42%
ADC0808 8-Bit A/D Converter with 8-Channel Multiplexer IC DIP-28 Package
Original price was: ₹180.00.₹140.00Current price is: ₹140.00. inc. GST
PCF8583 IC
Original price was: ₹100.00.₹65.00Current price is: ₹65.00. inc. GST
PCF8582E-2 IC DIP-8
Original price was: ₹60.00.₹35.00Current price is: ₹35.00. inc. GST
- Low power CMOS
- Non-volatile storage of 2 kbits organized as 256 × 8-bitÂ
- Â Single supply with full operation down to 2.5 VÂ
- Â On-chip voltage multiplierÂ
- Â Serial input/output I2C-busÂ
- Write operations:Â
- Â Â Â Â Â Â Â Â Â Â Â Â Â –Â byte write modeÂ
                          – 8-byte page write mode (minimizes total write time per byte)
- Â Read operations:Â
                         – sequential readÂ
                         – random readÂ
- Â Internal timer for writing (no external components)Â
- Â Internal power-on resetÂ
- Â 0 kHz to 100 kHz clock frequency
- High reliability by using a redundant storage code
Description
The PCF8582 is a 256×8 CMOS EEPROM with an I2C interface. It comes in a range of plastic 8- and 16-pin units. The 16-pin Dual In-Line package is utilized in this specific arrangement. A 128×8 CMOS EEPROM, PCF8581. Philips television sets that utilize I2C EEPROMs can have their default setup parameters programmed with this Gang Programmer. In addition to demonstrating how to build an I2C interfaced programmer, the design is offered here as an illustration of how to use the 87C751 I2C interface. The data is copied into ten slave EEPROMs by the programmer after being read from a source EEPROM.
The programmer is powered by a 9V @ 300mA wall-mounted source. On the board, there is a 5V regulator. A yellow LED is used to show that the board has received power. There are red LEDs at each socket to signal a failure in the programming procedure for that IC, and green and pink LEDs to indicate the status of the programming operation. If everything goes according to plan, a buzzer will sound and a green LED will show that the programming procedure was successful. If there are any EEPROM faults, the pink LED will illuminate, and the relevant red LED will flash to show which IC is malfunctioning. The I2C communication link has malfunctioned if the pink LED is on but none of the red LEDs are lit.
Reviews (0)
Shipping & Delivery
Related products
5-36v Switch Drive High-power MOSFET Trigger Module
- Operating Voltage: DC 5V - 36V;
- The trigger source: digital high-low (DC3.3V - 20V), can be connected microcontroller IO port, PLC interfaces, DC power, you can access the PWM signal, the signal frequency 0--20KHZ perfect support.
- Output capacity: DC 5V - 36V, at room temperature, continuous current 15A, power 400W! Lower auxiliary cooling conditions, the maximum current up to 30A.
- Applications: You can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, etc.. You can enter
- PWM, motor speed control, lamp brightness.
- Availability: unlimited switch
- Operating temperature: -40-85
- Dimension: 34mm x 17mm x 12mm
- The use of imported dual-MOS parallel active output, lower resistance, more current, strong power at room temperature, 15A, 400W, to meet the most use of the equipment
- Wide voltage, the perfect support for PWM
- Easily control high power devices
- Input PWM to achieve motor speed control, lamp brightness control
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
Solid State Relay SSR-40DD 40A 3-32V DC to 5-60V DC SSR 40DD Relay Solid State
- Model: SSR-40 DD.
- Control mode: DC-DC
- Input voltage: 3-32V DC.
- Output voltage: 5-60V DC.
- Output current: 40A.
- On voltage: ≤1v.
- One-off time: ≤10ms.
- Off leakage current: ≤2ma.
- Loading current: 40A
- Control current: 3-25mA DC
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Weight: 0. 106Kg.
TP5100 4.2v 8.4v Single Double Lithium Battery Charge Management Li-ion Battery Compatible 2A Charging Board
- Input voltage: 5-15V DC power supply.
- Charge status: full and unloaded blue lights, charging red.
- Double 8.4v / 4.2v lithium rechargeable single .
- Programmable charge current. 0. 1A-2A .
- Programmable steady precharge current 10% -100%.
- Wide operating voltage, maximum reach I8V.
- Red and green LED charge status indicator.
- Chip temperature protection, overcurrent protection, under voltage protection.
- Battery temperature protection, reverse battery shutdown, short circuit protection.
- Switching frequency 400Khz, usable inductance 20uH and more.
- PWR_ON Power battery for switching control.
XT60 Connector
- Manufacturer: AMASS
- Connector Series: XT60H
- Rated Voltage: DC 500V
- Metal Material: Brass Gold Plated
- Rated Current: 30A
- Momentary Current: 60A
- Number of pins: 2
- Colour: Yellow
- Contact Resistance: 0.55mΩ
- FR Level: UL94 V0
- Use Times: 1000 TIMES
- Temperature: -20℃ to 120℃
- Spatial Orientation Straight
- Compatible for Wire size up to 12AWG
- Mechanical mounting for cable
- Electrical mounting soldered
- Contact plating Gold flash
Reviews
There are no reviews yet.