I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
TEA1062A Low Voltage Transmission Circuits with Dialer Interface IC
₹30.00 Original price was: ₹30.00.₹20.00Current price is: ₹20.00. inc. GST
- Low Voltage Transmission Circuits with Dialer Interface
- Line Voltage: 4V
- Internal Supply Current Max: 1.35mA
- Microphone Amplifier Voltage Gain: 52dB
- Receiving Amplifier Voltage Gain: 31dB
- Common Mode Rejection Ratio (Mic): 82dB
- Package: DIP-16
aria-labelledby=”at-3a0221cb-4417-4921-a94d-04561afb5bc2″>
 </div>
The TEA1062A is an integrated circuit that performs all voice and line interface tasks in fully electronic telephone systems. These gadgets are designed to transition between dialling and speaking via electrical switching. To allow for the usage of several telephone sets linked in parallel, the ICs function at line voltages as low as 1.6 V DC (with decreased performance.
The telephone line provides the power necessary for the IC and its peripheral circuitry. The IC regulates the supply voltage, which is obtained from the line through a dropping resistor. External circuits, such as dialling and control circuits, are likewise powered by the supply voltage VCC. A capacitor between VCC and VEE is used to decouple the supply voltage. A capacitor between REG and VEE decouples the internal voltage regulator. Meanwhile, the exchange supply voltage Vexch, the feeding bridge resistance Rexch, and the DC resistance of the telephone line Rline define the DC current flowing into the set.
A 3.6 k resistor connected between STAB and VEE controls the amount of the circuit’s inbuilt current stabiliser (see Fig.9). The surplus current is shunted to VEE through LN when the line current (Iline) is more than 0.5 mA larger than the total of the IC supply current (ICC) and the current drawn by peripheral circuitry linked to VCC (Ip). Calculate the regulated voltage on the line terminal (VLN) as follows:
VLN = Vref + ISLPE × R9
VLN = Vref + {(Iline − ICC − 0.5 × 10−3 A) − Ip} × R9
Vref is an internally generated temperature compensated reference voltage of 3.7 V and R9 is an external resistor connected between SLPE and VEE.

Related products
1/4W 5% Assorted Value Carbon Film Resistor Assortment Kit Set pack electronic diy kit
- 100% brand new and high quality.
- Fine workmanship and long service life.
- 1/4W carbon film resistor package.
- High precision and stability.
- Easy to use.
- Precision: 5%
- Error: 5%
- Values
- 10Ω, 15Ω, 22Ω, 33Ω, 47Ω, 68Ω, 100Ω, 220Ω, 330Ω, 470Ω, 1k, 1k5, 2k2, 3k3, 4k7, 5k6, 6K8, 8K2, 10K, 15K, 22K, 33K, 47K, 56K, 68K, 100K, 150K, 220K, 330K, 470K
- Package included: 150pcs
120pcs 12 values 0.22UF-470UF Aluminum electrolytic capacitor assortment kit set pack
25pcs Button Switch Kit
- Relative Humidity: 95%
- Rated Voltage: 12V
- Rated Current: 50 mA
- Contact resistance: 50M Ohm Max (initial)
- The insulation resistance: 100M Ohm minDC (250V)
- The compressive strength: AC250V (50/60Hz for 1 minute)
- Mechanical life: 100000 cycles
- The environment temperature: 25° ~ + 105°
- The operating strength: 180/250 (plus or minus 30gf)
- Dimension: 12 * 12 * 7.3 round convex type
- Total Buttons: 25pcs
- Colours: 5 (Black, Red, White, Blue, Yellow)
AP Extension pigtail SMA female socket jack to UFL IPX Connector
GSM Antenna Dlenp 2dbi/3dbi Patch Antenna with SMA Male Connector
- GSM Antenna
- Gain: 2 to 3dbi
- Wire Length: 3 metre
- 3dbi Sticker Antenna
- GSM Antenna
- SMA Male Connector
- Frequency Range(MHz): 824-960/1710-1990Mhz
- Bandwidth (MHz): 136/280
- VSWR≤1.5
- Gain(dB): 2-3dbi
- Max Input power(W): 60W
- Input Impedance: 50 Ω
- Polarization Type: Vertical
- Cable Type: RG174
- Mounting Adhesive
- Net weight: 47g
HX711–24 Bit Analog to Digital Converter (ADC)
- It is an ADC converter with two differential input channels
- An active-low noise PGA is integrated inside the chip which provides the gain of 32, 64 and 128
- It has a power-on-reset capability which simplifies digital interface initialization.
- All controls to the IC are made through the pins. Programming is not needed.
- You can select a data rate of 10SPS or 80SPS at the output.
- Provides simultaneous supply rejection of 50Hz and 60Hz supply.
- Built-in analog power supply regulator
- The voltage supply range is from 2.6V to 5.5V
- The temperature range is from -40 °C to +85℃
SIM Card Holder
Solid State Relay Module SSR-25DA 25A /250V 3-32V DC Input 24-380VAC Output
- Control mode: DC-AC
- Input voltage: 3-32V DC.
- Output voltage: 24-380V AC.
- Output current: 25A.
- Working voltage: 250V.
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Dimension: 6. 5Cm x 4. 5Cm x 2. 2Cm

Reviews
There are no reviews yet.