I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
TEA1062A Low Voltage Transmission Circuits with Dialer Interface IC
₹30.00 Original price was: ₹30.00.₹20.00Current price is: ₹20.00. inc. GST
- Low Voltage Transmission Circuits with Dialer Interface
- Line Voltage: 4V
- Internal Supply Current Max: 1.35mA
- Microphone Amplifier Voltage Gain: 52dB
- Receiving Amplifier Voltage Gain: 31dB
- Common Mode Rejection Ratio (Mic): 82dB
- Package: DIP-16
aria-labelledby=”at-3a0221cb-4417-4921-a94d-04561afb5bc2″>
 </div>
The TEA1062A is an integrated circuit that performs all voice and line interface tasks in fully electronic telephone systems. These gadgets are designed to transition between dialling and speaking via electrical switching. To allow for the usage of several telephone sets linked in parallel, the ICs function at line voltages as low as 1.6 V DC (with decreased performance.
The telephone line provides the power necessary for the IC and its peripheral circuitry. The IC regulates the supply voltage, which is obtained from the line through a dropping resistor. External circuits, such as dialling and control circuits, are likewise powered by the supply voltage VCC. A capacitor between VCC and VEE is used to decouple the supply voltage. A capacitor between REG and VEE decouples the internal voltage regulator. Meanwhile, the exchange supply voltage Vexch, the feeding bridge resistance Rexch, and the DC resistance of the telephone line Rline define the DC current flowing into the set.
A 3.6 k resistor connected between STAB and VEE controls the amount of the circuit’s inbuilt current stabiliser (see Fig.9). The surplus current is shunted to VEE through LN when the line current (Iline) is more than 0.5 mA larger than the total of the IC supply current (ICC) and the current drawn by peripheral circuitry linked to VCC (Ip). Calculate the regulated voltage on the line terminal (VLN) as follows:
VLN = Vref + ISLPE × R9
VLN = Vref + {(Iline − ICC − 0.5 × 10−3 A) − Ip} × R9
Vref is an internally generated temperature compensated reference voltage of 3.7 V and R9 is an external resistor connected between SLPE and VEE.

Related products
120pcs 12 value 1uF-470uF Electrolytic Capacitor Kit 1UF 2.2UF 3.3UF 4.7UF 10UF 22UF 33UF 47UF 100UF 220UF
25pcs Button Switch Kit
- Relative Humidity: 95%
- Rated Voltage: 12V
- Rated Current: 50 mA
- Contact resistance: 50M Ohm Max (initial)
- The insulation resistance: 100M Ohm minDC (250V)
- The compressive strength: AC250V (50/60Hz for 1 minute)
- Mechanical life: 100000 cycles
- The environment temperature: 25° ~ + 105°
- The operating strength: 180/250 (plus or minus 30gf)
- Dimension: 12 * 12 * 7.3 round convex type
- Total Buttons: 25pcs
- Colours: 5 (Black, Red, White, Blue, Yellow)
5 Pin RMC Connector
ADXL 335 Accelerometer IC
- 3-axis sensing
- Small, low profile package
- 4 mm × 4 mm × 1.45 mm LFCSP
- Low power : 350 μA (typical)
- Single-supply operation: 1.8 V to 3.6 V
- 10,000 g shock survival
- Excellent temperature stability
- BW adjustment with a single capacitor per axis
- RoHS/WEEE lead-free compliant
- 8V- 3.6V single-supply operation
- Integrated X, Y, and Z axis accelerometer on a single chip
- X and Y axis has a 0.5Hz to 1600Hz bandwidth
- Z axis has a 0.5Hz to 550Hz bandwidth
- Hermetically sealed for temp and humidity resistance
GSM Antenna
IR LED Sensor
- Size: 5mm LED
- Wavelength: 940nm wavelength (most commonly used)
- Forward current (IF) is 100mA (normal condition) and 300mA (max.)
- 5A of surge forward current
- 24v to 1.4v of forward voltage
- Temperature : -40 to 100 ℃
- Soldering Temperature should not exceed 260 ℃
- Power Dissipation of 150mW at 25℃ (free-air temperature) or below
- Spectral bandwidth of 45nm
- Viewing angle: 30 to 40 degree
- High Reliability
- Excessive radiant intensity
- Having lead spacing of 2.54mm
- Easy to use with breadboard or perf board
SIM Card Holder
XT60 Connector
- Manufacturer: AMASS
- Connector Series: XT60H
- Rated Voltage: DC 500V
- Metal Material: Brass Gold Plated
- Rated Current: 30A
- Momentary Current: 60A
- Number of pins: 2
- Colour: Yellow
- Contact Resistance: 0.55mΩ
- FR Level: UL94 V0
- Use Times: 1000 TIMES
- Temperature: -20℃ to 120℃
- Spatial Orientation Straight
- Compatible for Wire size up to 12AWG
- Mechanical mounting for cable
- Electrical mounting soldered
- Contact plating Gold flash

Reviews
There are no reviews yet.